Hoshizaki DCM-300BAH(-OS) User's Manual
Contents
1. E MLA 2 a u Il E j os Tp me uu NEN ED ele H 4 ul amp E m A E 1 1 pon 1 E m z E a A 1 E zi H m oS E al s E3 Il Installation and Operating Instructions WARNING 1 This icemaker must be installed in accordance with applicable national state and local codes and regulations 2 CHOKING HAZARD Ensure all components fasteners and thumbscrews are securely in place after installation Make sure that none have fallen into the storage bin A Checks Before Installation Visually inspect the exterior of the shipping container and immediately report any damage to the carrier Upon opening the container any concealed damage should also be immediately reported to the carrier Remove the shipping carton tape and packing material If any are left in the icemaker it will not work properly Remove the panels to prevent damage when installing the icemaker See II B How to Remove Panels Remove the package containing the accessories Remove the protective plastic film from the panels If the icemaker is exposed to the sun or to heat remove the film after the icemaker cools Check that the refrigerant lines do not rub or touch lines or other surfaces and that the fan blade if applicable turns freely Check that the compressor is snug on al2. ELECTRICAL CONNECTION THIS UNIT MUST BE GROUNDED Failure to properly ground or wire this unit could result in death serious injury or severe damage to the icemaker The white lead must be connected to the neutral conductor of the power source See diagram below 115 120 60 1 JUNCTION BOX L BROWN 115 120V F Water Supply and Drain Connections See Fig 4 WARNING 1 Water supply and drain connections must be installed in accordance with applicable national state and local codes and regulations 2 Normal operating water temperature should be within 45 F to 90 F 7 C to 32 C Operation of the icemaker for extended periods outside of this normal temperature range may affect icemaker performance 3 To prevent damage to equipment do not operate the icemaker when the water supply is off or if the pressure is below 10 PSIG Do not run the icemaker until the proper water pressure is reached A plumbing permit and services of a licensed plumber may be required in some areas External filters strainers or softeners may be required depending on water quality Contact your local Hoshizaki distributor for recommendations Water supply pressure should be a minimum of 10 PSIG and a maximum of 113 PSIG If the pressure exceeds 113 PSIG the use of a pressure reducing valve is required The storage bin drain line and drip tray drain line must be run separately Drain lines must have
3. Model Number Serial Number Complete and detailed explanation of the problem This manual should be read carefully before the icemaker is installed operated Only qualified service technicians should install service and maintain the icemaker Read the warnings contained in this booklet carefully as they give important information regarding safety Please retain this booklet for any further reference that may be necessary CONTENTS Important Safety Information 4 Bicis re 5 5 1 DEM 300BAH air cooled Fr erreen 5 2 DCM 300BAH OS lt lt 6 B Dimensions Connections 7 1 DOM 300BAH air cooled 7 2 DCM 300BAH OS 8 Il Installation and Operating Instructions 444404240 0 9 A Checks Before 2 4 44040000 9 How to Remove Panels p COE 10 C Locations ETT I UTERE 11 BE tv Y Y 11 E Electrical
4. 7 C to 32 C Operation of the icemaker for extended periods outside of these normal temperature ranges may affect icemaker performance 2 This icemaker will not work at sub freezing temperatures To prevent damage to the water supply line drain the icemaker if the air temperature is going to go below 32 F 0 C See Preparing the Icemaker for Long Storage IMPORTANT Opti Serve Models OS Sunlight direct and indirect can have an effect on the operation of the dispense sensors If a problem is noticed the icemaker should be moved out of direct sunlight and or farther away from any outside windows For best operating results The icemaker should not be located next to ovens grills or other high heat producing equipment e The location should provide a firm and level foundation for the equipment Allow 6 15 cm clearance at rear and sides for proper air circulation and ease of maintenance and or service should they be required Allow 24 61 cm clearance at top to allow for removal of the auger D Setup 1 Position the icemaker in the selected permanent location If applicable attach optional 6 legs or attach to an optional stand If attaching to a stand refer to the instructions included with the stand 2 Level the icemaker in both the left to right and front to rear directions If using optional 6 legs or an optional stand adjust the legs to make the icemaker level 3 If mounting flat
5. and thumbscrews are securely in place after installation Make sure that none have fallen into the storage bin 1 Is the icemaker level 2 Is the icemaker in a site where the ambient temperature is within 45 F to 100 F 7 C to 38 C and the water temperature within 45 F to 90 F 7 C to 32 C all year around 3 Is there at least 6 15 cm clearance at rear and sides and 24 61 cm at top for proper air circulation and ease of maintenance and service 4 Have the shipping carton tape and packing material been removed from the icemaker 5 If the icemaker is mounted flat to a counter has the perimeter where the icemaker contacts the counter been sealed with approved caulk compound If the icemaker is on a stand has it been secured to the stand as outlined in the stand s instructions 6 Have all electrical and water connections been made Do electrical and water connections meet all national state and local code and regulation requirements 7 Has the power supply voltage been checked or tested against the nameplate rating Has a proper ground been installed to the icemaker 8 Are the water supply line shut off valve and drain valve installed Has the water supply pressure been checked to ensure a minimum of 10 PSIG and a maximum of 113 PSIG Note The icemaker may stop running when the water supply is off or if the pressure is below 10 PSIG When the proper water pressure is reached the icemaker automatically starts running a
6. storage bin 13 Move the power switch to the ON position then replace the front panel in its correct position Turn on the power supply then move the control switch to the ICE position to start the automatic icemaking process Dispense Mode Switch The dispense mode switch has CONTINUOUS and PORTION positions When the dispense mode switch is in the CONTINUOUS position ice dispenses continuously for a maximum of 60 seconds per activation When the dispense mode switch is in the PORTION position ice dispenses for the amount of time determined by the ice dispense time setting The ice dispense time control is located on the control board The dial indicates dispense time in seconds See Fig 6 When shipped the ice dispense time control is set to the minimum dispense time of 0 6 sec At this setting approximately 0 72 oz of ice is dispensed The DCM 300BAH OS dispenses approximately 1 2 oz of ice per second Ill Cleaning and Maintenance This icemaker must be cleaned and maintained in accordance with the instruction manual and labels provided with the icemaker Consult with your local distributor about cleaning and maintenance service To obtain the name and phone number of your local distributor visit www hoshizaki com or call Hoshizaki Technical Support at 1 800 233 1940 in the USA WARNING 1 Only qualified service technicians should service this icemaker 2 CHOKING HAZARD Ensure all components
7. ERANT 404A 15 9 02 MOTOR COMPRESSOR THERMALLY PROTECTED NOT INTENDED FOR OUTDOOR USE Hoshizaki America Inc Peachtree City GA www hoshizaki com For certification marks see the nameplate on the rear panel The rating label and nameplate provide electrical and refrigerant data The rating label can be seen by removing the front panel The nameplate is located on the rear panel We reserve the right to make changes in specifications and design without prior notice 2 DCM 300BAH OS air cooled HOSHIZAKI ICE MAKER NUMBER DCM 300BAH OS AL NUMBER UPPLY VOLTAGE 115 120 60 1 RESSOR 120V 7 9RLA 39 0LRA MOTOR 120V 1 45FLA 80W MOTOR 115V 0 8FLA 16W ITATING MOTOR 120V 0 9FLA 55W PENSING MOTOR LA 55W M FUSE SIZE AMPS ACR BREAKER USA ONLY AMPS IRC BREAKER CANADA ONLY AMPS M CIRCUIT AMPACITY AMPS PRESSURE HI 460PSI LO 290PSI ERANT 404A 15 9 02 MOTOR COMPRESSOR THERMALLY PROTECTED NOT INTENDED FOR OUTDOOR USE Hoshizaki America Inc Peachtree City GA www hoshizaki com For certification marks see the nameplate on the rear panel The rating label and nameplate provide electrical and refrigerant data The rating label can be seen by removing the front panel The nameplate is located o
8. Remove the float switch assembly from the reservoir cover b Wipe down the float switch assembly with the cleaning solution c Rinse the float switch assembly thoroughly with clean water d Replace the float switch assembly in its correct position 10 Move the power switch to the ON position and replace the panels in their correct positions Turn on the power supply then move the control switch to the ICE position Make ice using the solution until the icemaker stops making ice Note This unit will not run if the safety switch is not engaged 11 Move the control switch to the DRAIN position Allow the water system to drain for 5 minutes 12 Move the control switch to the ICE position Open the icemaker water supply line shut off valve to supply water to the reservoir 13 After the gear motor starts move the control switch to the DRAIN position Allow the water system to drain for 5 minutes Note If you do not sanitize the unit move the control switch to the ICE position after the water system drains Allow the icemaker to run for 30 minutes then move the control switch to the OFF position Turn off the power supply then remove the front panel and storage bin cover Move the power switch to the OFF position Go to step 12 in 2 Cleaning and Sanitizing Procedure under Dispensing Components 14 Move the control switch to the OFF position then turn off the power supply 15 Close the icemaker water
9. to a counter seal the perimeter where the icemaker contacts the counter with approved caulk compound in a smooth and easily cleanable manner 4 Replace the panels in their correct positions 11 E Electrical Connection WARNING 1 Electrical connection must be hard wired and must meet national state and local electrical code requirements Failure to meet these code requirements could result in death electric shock serious injury fire or extensive damage to equipment 2 This unit requires an independent power supply See the nameplate for proper voltage and breaker fuse size Failure to use a proper breaker or fuse can result in a tripped breaker blown fuses or damage to existing wiring This could lead to heat generation or fire 3 THIS UNIT MUST BE GROUNDED Failure to properly ground this unit could result in death or serious injury 4 Electrical connection must be made in accordance with the instructions on the WARNING tag provided with the pig tail leads in the junction box See Fig 3 Usually an electrical permit and services of a licensed electrician are required The maximum allowable voltage variation is 10 percent of the nameplate rating The white lead must be connected to the neutral conductor of the power source CAUTION Miswiring may result in severe damage to the icemaker See Fig 3 The opening for the power supply connection is 7 8 DIA to fit a 1 2 trade size conduit A WARNING
10. 1 4 fall per foot 2 cm per 1 m on horizontal runs to get a good flow A vented tee connection is also required for proper flow Drain lines should not be piped directly to the sewer system An air gap of a minimum of 2 vertical inches 5 cm should be between the end of the drain pipes from the storage bin and drip tray and the floor drain 13 1 lcemaker cemaker water supply inlet is 1 2 female pipe thread FPT A minimum of 1 4 nominal ID copper water tubing or equivalent is required for the icemaker water supply line An icemaker water supply line shut off valve and drain valve should be installed e Storage bin and drip tray drain outlets are 3 4 A minimum of 3 4 nominal ID hard pipe or equivalent is required for the storage bin and drip tray drain lines Icemaker Icemaker Water Supply Icemaker Water Line Shut Off Valve Supply Inlet 1 2 Minimum 1 4 Nominal ID Copper Water Tubing Drip Tray Drain Outlet 3 4 FPT Vent Icemaker Water Supply Tube Line Drain Valve Storage Bin Drain Outlet 3 4 FPT sand Separate piping to approved drain Leave a 2 inch 5 cm vertical air gap between the end of each pipe and the drain Minimum 3 4 Nominal ID 2 inch 5 Hard Pipe air gap DCM 300BAH OS Floor prain Fig 4 14 Final Checklist WARNING CHOKING HAZARD Ensure all components fasteners
11. 12 F Water Supply and Drain 13 EE ENS qo NN UU T E T AT 15 uem i RTTT M 16 Dispense Mode Switch anna nm han 17 Cleaning and 18 A Cleaning and Sanitizing 40 4 0 0 enne 19 Doce ccu m 19 2 Dispensing Components RES een 21 MU cipe TP P 23 C Preparing the Icemaker for Long 2 2400 24 Important Safety Information Throughout this manual notices appear to bring your attention to situations which could result in death serious injury or damage to the unit A WARNING Indicates a hazardous situation which could result in death or serious injury CAUTION Indicates a situation which could result in damage to the unit IMPORTANT Indicates important information about the use and care of the unit WARNING This icemaker should be destined only to the use for which it has been expressly conceived Any other use should be considered improper and therefore dangerous The manufacturer cannot be held responsible for injury or damage resulting from improper incorrect and unreasonable use To reduce the risk of death electric shock serious injury or fire follow basic precautions including the following Only qualified servi
12. Hoshizaki America Inc Cubelet Icemaker Dispenser Models DCM 300BAH OS INSTRUCTION MANUAL A Superior Degree of Reliability www hoshizaki com Issued 3 2 2011 Only qualified service technicians should install service and maintain the icemaker No installation service or maintenance should be undertaken until the technician has thoroughly read this Instruction Manual Likewise the owner manager should not proceed to operate the icemaker until the installer has instructed them on its proper operation Failure to install operate and maintain the equipment in accordance with this manual may adversely affect safety performance component life and warranty coverage Hoshizaki provides this manual primarily to assist qualified service technicians in the installation maintenance and service of the icemaker Should the reader have any questions or concerns which have not been satisfactorily addressed please call write or send an e mail message to the Hoshizaki Technical Support Department for assistance HOSHIZAKI AMERICA INC 618 Highway 74 South Peachtree City GA 30269 Attn Hoshizaki Technical Support Department Phone 1 800 233 1940 Technical Support 770 487 2331 Fax 1 800 843 1056 770 487 3360 E mail techsupport 9 hoshizaki com Web Site www hoshizaki com NOTE To expedite assistance all correspondence communication MUST include the following information
13. ce technicians should install service and maintain the icemaker Electrical connection must be hard wired and must meet national state and local electrical code requirements Failure to meet these code requirements could result in death electric shock serious injury fire or severe damage to equipment This unit requires an independent power supply See the nameplate for proper voltage and breaker fuse size Failure to use a proper breaker or fuse can result in a tripped breaker blown fuse or damage to existing wiring This could lead to heat generation or fire THIS UNIT MUST BE GROUNDED Failure to properly ground this unit could result in death or serious injury Move the control switch and the power switch to the OFF position and turn off the power supply before servicing Lockout Tagout to prevent the power supply from being turned back on inadvertently Do not make any alterations to the unit Alterations could result in electric shock injury fire or damage to the unit Specifications Electrical Data 1 DCM 300BAH air cooled HOSHIZAKI ICE MAKER NUMBER DCM 300BAH AL NUMBER UPPLY VOLTAGE 115 120 60 1 PRESSOR 120V 7 9RLA 39 0RLA MOTOR 120V 1 45FLA 80W MOTOR 115V 0 8FLA 16W ITATING MOTOR 120V 0 9FLA 55W PENSING MOTOR 120V 0 9FLA 55W 120V 0 2A M FUSE SIZE 20 AMPS ACR BREAKER USA ONLY 20 AMPS IRC BREAKER CANADA ONLY 20 AMPS M CIRCUIT AMPACITY 20 AMPS PRESSURE HI 460PSI LO 290PSI
14. eaning Procedure 1 Close the icemaker water supply line shut off valve 2 Move the control switch to the DRAIN position See Fig 7 Allow the water system to drain for 5 minutes 3 Move the dispense mode switch to the CONTINUOUS position then dispense all of the ice from the storage bin Note Ice dispenses continuously for a maximum of 60 seconds per activation 4 Move the control switch to the OFF position then turn off the power supply Remove the front and top panels then move the power switch to the OFF position 5 Remove the storage bin cover Remove spout B then remove spout A 6 Pour the cleaning solution over the extruding head until the evaporator assembly and the reservoir are full and the solution starts to overflow into the drain pan Note If there is excess scale on the extruding head fill the evaporator assembly and reservoir as described above then use a clamp on the reservoir hose between the reservoir and evaporator assembly to block flow Pour additional cleaning solution over the extruding head until the evaporator assembly is completely full 7 Replace spout A spout B and the storage bin cover in their correct positions 8 Allow the icemaker to sit for 10 minutes before operation If you placed a clamp on the reservoir hose in step 6 remove it before operation 19 9 In bad or severe water conditions clean the float switch assembly as described below Otherwise continue to step 10 a
15. fasteners and thumbscrews are securely in place after any cleaning or maintenance is done to the unit Make sure that none have fallen into the storage bin 3 The storage bin is for ice use only Do not store anything else in the storage bin 2 Agitator Float Switch 2 7 Assembly 18 Evaporator Assembly _ Dispensing 2 Auger Agitating Motor Dispensing Motor OFF DISPENSE MODE Ne SN A Spout Cover PORTION f 2 77 CONTINUOUS Safety Switch f Optical Sensors OS model Fig 7 18 Cleaning and Sanitizing Instructions Hoshizaki recommends cleaning and sanitizing this unit at least twice a year More frequent cleaning and sanitizing however may be required in some existing water conditions WARNING 1 To prevent injury to individuals and damage to the icemaker do not use ammonia type cleaners 2 Carefully follow any instructions provided with the bottles of cleaning and sanitizing solution 3 Always wear liquid proof gloves and goggles to prevent the cleaning and sanitizing solutions from coming into contact with skin or eyes 4 Do not use ice made from the cleaning and sanitizing solutions After cleaning and sanitizing be careful not to leave any solution on the parts or in the storage bin 1 Water System a Cleaning Solution Dilute 9 6 fl oz 0 29 I of Hoshizaki Scale Away with 1 6 gal 6 0 I of warm water b Cl
16. gain 9 Are the compressor hold down bolts snug Have the refrigerant lines been checked to make sure they do not rub or touch other lines or surfaces Has the fan blade been checked to make sure it turns freely 10 Are all components fasteners and thumbscrews securely in place 11 Has the end user been given the instruction manual and instructed on how to operate the icemaker and the importance of the recommended periodic maintenance 12 Has the end user been given the name and telephone number of an authorized service agent 13 Has the warranty card been filled out and forwarded to the factory for warranty registration 15 Startup WARNING 1 All parts are factory adjusted Improper adjustments may adversely affect safety performance component life and warranty coverage 2 If the icemaker is turned off wait for at least minutes before restarting the icemaker to prevent damage to the compressor 3 At startup confirm that all internal and external connections are free of leaks 1 Open the water supply line shut off valve 2 Move the control switch to the OFF position See Fig 5 3 Remove the front panel then move the power switch to the ON position Replace the front panel in its correct position then turn on the power supply Note This unit will not run if the safety switch is not engaged 4 Move the control switch to the ICE position to start the automatic icemaking process 5 Once
17. he Service Manual for details After Upper Bearing Inspect Replace both upper bearing and lower bearing if wear exceeds 3 Years extruding head recommendations Replace the mechanical seal if the seal s contact then Yearly Lower Bearing surfaces are worn cracked or scratched and O Ring lower housing Mechanical Seal Evaporator Oylinder Auger Yearly Inlet Water Valve Close the icemaker water supply line shut off valve and drain the water and Drain Valve system Clean the inlet water valve screen and clean and inspect the drain valve 23 C Preparing the Icemaker for Long Storage CAUTION When storing the icemaker for an extended time or in sub freezing temperatures follow the instructions below to prevent damage When the icemaker is not used for two or three days under normal conditions itis sufficient to only move the control switch to the OFF position When storing the icemaker for extended time or in sub freezing temperatures follow the instructions below 1 Remove the ice from the storage bin drain the water system and remove the water from the icemaker water supply line 1 Close the icemaker water supply line shut off valve and open the icemaker water supply line drain valve 2 Move the control switch to the DRAIN position Allow the water system to drain for 5 minutes 3 Move the dispense mode switch to the CONTINUOUS position then dispense all of the ice from the storage b
18. in Note Ice dispenses continuously for a maximum of 60 seconds per activation 4 Attach a compressed air or carbon dioxide supply to the icemaker water supply line drain valve 5 While engaging the water dispense switch blow out the water dispense valve using the compressed air or carbon dioxide supply After blowing out the water dispense valve leave the compressed air or carbon dioxide supply flowing Move the control switch to the ICE position to open the inlet water valve and briefly blow out the inlet water valve After blowing out the inlet water valve move the control switch to the OFF position 6 Close the icemaker water supply line drain valve 7 Turn off the power supply then remove the front panel and move the power switch to the OFF position 8 Remove the storage bin cover Clean the storage bin liner and the storage bin cover using a neutral cleaner Rinse thoroughly after cleaning Replace the storage bin cover and the front panel in their correct positions 24 HOSHIZAKI AMERICA INC 618 Hwy 74 S Peachtree City GA 30269 USA TEL 770 487 2331 770 487 3360 www hoshizaki com 91A2AD10A
19. l mounting pads See the nameplate on the rear panel and check that your voltage supplied corresponds with the voltage specified on the nameplate This icemaker can be installed on a countertop or on an optional stand If using an optional stand Hoshizaki Stand SD 450 or SD 500 is recommended For further options contact your local Hoshizaki distributor How to Remove Panels See Fig 1 or Fig 2 Front Panel Remove the screw Lift up and towards you Disconnect the connector on push button models Top Panel Lift up at front slightly push rearward and lift off Apron Panel Remove the screws and pull towards you Disconnect the connectors on Opti Serve models e Side Panels Remove the screws and pull towards you e Storage Bin Cover Remove the thumbscrews and pull towards you DCM 300BAH Push Button Models Top Panel Storage Bin Cover _ IE Side Panel STS Side Panel 4 Front Panel Connector Apron Panel Fig 1 DCM 300BAH OS Opti Serve Models m Storage Bin PR Tp Panel Side Panel Cover m ae At Side Panel E Y Front Panel C Location CAUTION 1 This icemaker is not intended for outdoor use Normal operating ambient temperature should be within 45 F to 100 F 7 C to 38 C Normal operating water temperature should be within 45 F to 90 F
20. n the rear panel We reserve the right to make changes in specifications and design without prior notice B Dimensions Connections 1 DCM 300BAH air cooled TRA TLET 3 4 pay c l 1 E psu E zn E zx m MLL a wT da amp 9 m Se xn 2 i 121 158711 I 81 ELS 2 DCM 300BAH OS air cooled Unit mm in L E ELECTRICAL 1
21. ng turned back on inadvertently Maintenance Schedule FreaueneyJarea Task Every 2 Air Filter Inspect Wash with warm water and neutral cleaner if dirty Weeks Monthly External Water Check for proper pressure and change if necessary Filters Icemaker Exterior Wipe down with a clean soft cloth Use a damp cloth containing a neutral cleaner to wipe off oil or dirt build up Clean any chlorine staining rust colored spots using a non abrasive cleaner like Zud or Bon Ami Every 6 Icemaker and Clean and sanitize per the cleaning and sanitizing instructions provided in Months Storage Bin this manual Evaporator Wipe down with a clean cloth and warm water Slowly pour one cup of Condensate Drain sanitizing solution prepare as outlined in the sanitizing instructions in Pan and Gear this manual into the evaporator condensate drain pan Be careful not to Motor Drain Pan overflow the pan This solution will flow down to the gear motor drain pan and out the drain line to sanitize these areas Repeat with a cup of clean water to rinse Icemaker Storage Check to make sure they are clear Bin and Drip Tray Drains Condenser Inspect Clean if necessary by using a brush or vacuum cleaner Icemaker Inspect for oil spots loose components fasteners and wires Upper Bearing Check for wear using 02 round stock or pin gauge Replace both upper extruding head bearing and lower bearing if wear exceeds factory recommendations See t
22. ough 8 in the cleaning solution and then in the sanitizing solution for 15 minutes each Rinse the parts thoroughly with clean water On Opti Serve models OS wipe the optical sensors with cleaning solution and then with a clean damp cloth 10 Wipe the shutter located above the ice dispensing spout thoroughly with a clean cloth 11 Reassemble the bin control assembly and replace all parts in the reverse order of which they were removed 12 Pour warm water into the storage bin and melt any remaining ice Clean the storage bin liner and the storage bin cover using a neutral cleaner Rinse thoroughly after cleaning Replace the storage bin cover in its correct position 13 Move the power switch to the ON position then replace the panels in their correct positions Turn on the power supply then move the control switch to the ICE position to start the automatic icemaking process IE 1 2 pde y A SL Water Dispensing Nozzle Ice Dispensing Spout Spout Cover Fig 9 22 B Maintenance The maintenance schedule below is a guideline More frequent maintenance may be required depending on water quality the icemaker s environment and local sanitation regulations A WARNING 1 Only qualified service technicians should service this icemaker 2 Move the control switch and the power switch to the OFF position and turn off the power supply before servicing Lockout Tagout to prevent the power supply from bei
23. ove the control switch to the ICE position Allow the icemaker to run for 30 minutes then clean and sanitize the dispensing components as outlined below 2 Dispensing Components Perform after cleaning and sanitizing the water system as outlined above a Cleaning Solution Dilute 9 6 fl oz 0 29 I of Hoshizaki Scale Away with 1 6 gal 6 0 I of warm water b Sanitizing Solution Dilute 0 82 fl oz 25 ml of a 5 2596 sodium hypochlorite solution chlorine bleach with 1 6 gal 6 0 I of warm water c Cleaning and Sanitizing Procedure 1 Move the control switch to the OFF position then turn off the power supply 2 Remove the front and top panels then move the power switch to the OFF position 3 Remove the storage bin cover 4 Remove the motor bracket thumbscrews first from the vertical plane and then from the horizontal plane While holding on to the corresponding agitator or auger move the agitating motor or the dispensing motor towards you Remove the agitator and the dispensing auger from the storage bin See Fig 7 5 Remove the bin control assembly See Fig 8 6 Remove the snap pin shaft and actuator 7 Remove spout B spout A and their gaskets Spout B Spout A Bin Control Bracket Snap Pin Shaft Actuator 8 Remove the spout cover ice dispensing spout and water dispensing nozzle See Fig 9 9 Immerse the agitator dispensing auger and parts removed in steps 5 thr
24. supply line shut off valve c Sanitizing Solution Dilute 0 82 fl oz 25 ml of a 5 2596 sodium hypochlorite solution chlorine bleach with 1 6 gal 6 0 I of warm water d Sanitizing Procedure Following Cleaning Procedure 1 Make sure the control switch is in the OFF position the power supply is off and the icemaker water supply line shut off valve is closed 2 Remove the front and top panels then move the power switch to the OFF position 3 Remove the storage bin cover Remove spout B then remove spout A 4 Pour the sanitizing solution over the extruding head until the evaporator assembly and the reservoir are full and the solution starts to overflow into the drain pan 5 Replace spout A spout B and the storage bin cover in their correct positions 6 Allow the icemaker to sit for 10 minutes before operation 7 Move the power switch to the ON position and replace the panels in their correct positions Turn on the power supply then move the control switch to the ICE position Make ice using the solution until the icemaker stops making ice 8 Move the control switch to the DRAIN position Allow the water system to drain for 5 minutes 20 9 Move the control switch to the ICE position Open the icemaker water supply line shut off valve to supply water to the reservoir 10 After the gear motor starts move the control switch to the DRAIN position Allow the water system to drain for 5 minutes 11 M
25. the unit starts to produce ice allow it to run for another 30 minutes 6 Move the control switch to the DRAIN position Allow the water system to drain for 5 minutes 7 Move the dispense mode switch to the CONTINUOUS position then dispense all of the ice from the storage bin Note Ice dispenses continuously for a maximum of 60 seconds per activation 8 Remove the front panel then remove the storage bin cover 9 Move the control switch to the ICE position 10 Confirm bin control operation Engage the safety switch on the front frame See Fig 5 After the compressor starts press and hold the actuator paddle located inside the storage bin WARNING Keep hands hair and loose clothing clear of the agitator inside the storage bin The icemaker should shut down within 10 seconds TS Actuator Paddle EE re 2 th E as Storage Bin Cover Power Switch Control Box Cover Safety Switch CONTROL DISPENSE MODE A PORTION 77 CONTINUOUS 11 Disengage the safety switch Move the control switch to the OFF position then move the power switch to the OFF position Turn off the power supply 12 Clean the storage bin liner cover and components using a neutral cleaner Rinse thoroughly after cleaning Replace the storage bin cover in its correct position WARNING CHOKING HAZARD Ensure all components fasteners and thumbscrews are securely in place Make sure that none have fallen into the
Download Pdf Manuals
Related Search