Horizon Navigation NavMate Navigation System User's Manual
Contents
1. 0 9 VL max High level voltage VH min 4 0 VH min 5 Vehicle speed signal Green White Input pulse frequency 1 Hz to 200 Hz PCM square wave Input voltage range 13 to 26 Vmax 6 Not used 7 Not used 8 Not used s k 9 Not used 10 Not used 11 Not used gt gt 12 Not used gt 3 gt 13 Not used 14 Not used 15 Not used u 16 System power source Red 13 8 V DC nominal 3 Amp min Fuse battery plus block 3 3 Verify system starts and update software 1 Make sure ignition is OFF 3 Turn on ignition 4 Insert the CD ROM into the controller NavMate will update its software DO NOT TURN OFF THE IGNITION WHILE NAVMATE IS UPDATING 5 Verify that NavMate powers up correctly NOTE The Display should be connected before power is turned on 2 Connect wire harness to controller and video cable to controller and display unit MAORI TION 3 4 Mount components and tuck cables 1 Controller mounting Mount the controller to the vehicle using the brackets provided The controller must be firmly attached to the vehicle for the system to function properly Do not overtighten Do not mount the controller upside down The controller must be mounted level to within 5 degrees with the vehicle parked safely on reasonably level ground Use a bubble level to verify Follow the rules under the SAFTY INFORMATION AND PRECAUTIONS on page 3 Using a utility knife2. slit the carpeting as necessary Use double sided tape to secure the brackets underneath the carpet The two L shaped mounting brackets may be reversed for mounting to the floor NOTE Upon removal of the controller reverse procedure and seal carpet slit with double sided tape 2 GPS antenna mounting The GPS antenna must be mounted in a place that provides good visibility to the sky If a clear view cannot be obtained inside the vehicle due to a vertical windshield e g some delivery trucks the antenna may be mounted outside the vehicle The antenna has a magnet inside Using double sided tape mount the GPS antenna to the instrument panel or package shelf Plug the antenna cable into the controller 3 Display Unit Mounting Mount the display unit using the vehicle specific bracket or flex mount Do not overtighten See www panavise com for details 4 Tuck all cables into the vehicle sill Make sure the cables are not pinched or sharply bent 3 5 Setup Initialize and Calibrate The GPS should initialize in 7 15 minutes You do not need to be present during this time Take this opportunity to fill out the warranty registration for the system and place the User Manual and CD ROM case in the vehicle glove compartment When GPS is ready GPS icon on the map screen will change from Red to Green 1 Drive the vehicle approximately 10 15 miles to allow the system to find its current location and calibrate for the speed signal pulse rate
3. NavMate Navigation System Installation Manual Ver 1 0 1 0 COMPONENTS TABLE 1 Components COMPONENT LOCATION FUNCTION 1 Controller Mounts under a seat or in the trunk 2 Controller Brackets Mounts the controller to the vehicle 3 Display unit Mounts to the instrument panel 4 Display Bracket Mounts the display unit to the instrument panel 5 GPS Antenna Mounts on top of the instrument panel package shelf or outside Please refer to 2 GPS antenna mounting on page 6 6 Video Cable Connects the controller and display unit 7 Wire Harness Connects the controller to the necessary vehicle signals 8 User Manual 9 Map CD Contains the navigation software and map database Not included with kit Vehicle specific InDash brackets and an adapter for the NavMate display unit may be ordered from Panavise Refer to www panavise com for details Not included with kit The CD ROM for the appropriate geographic region must be ordered separately For more information please call 1 86NAVMATE1 1 866 286 2831 PLEASE VERIFY RECEIPT OF ALL COMPONENTS PRIOR TO ATTEMPTING TO INSTALL THE SYSTEM INTO A VEHICLE NavMate Installation Manual 2 0 SAFTY INFORMATION AND PRECAUTIONS 3 0 INSTALLATION 3 1 Determine system layout 1 Determine the location to connect to the vehicle speed signal Please call 1 86NAVMATE1 1 866 286 2831 for VSS help 2 Determine the location to connect to the remaining vehicle sign
4. als required by NavMate Please refer to Table 2 on pag e5 for signal requirements and NavMate wire colors 3 Determine general component layout e g where the controller will be mounted 3 2 Connect wires and route cables 1 Connect wire harness to vehicle using splice piggyback method Using a multimeter verify the battery ignition ground and backup connections The NavMate system wire harness has five wires which must be connected to the vehicle See Table 2 on pag e5 for requirements Ground Black Connect to a vehicle ground Maintain the shortest ground loop possible by connecting directly to a body ground point if available Ignition Pink Connect to a circuit which is powered only when the key is in the on run position An example is the turn signal circuit Battery Red Connect to a circuit which is powered constantly An example is the hazard signal circuit Reverse Light Green Connect to a circuit which is powered only when the vehicle is in reverse An example is the backup light Speed signal Green White OR Yellow The vehicle must have a vehicle speed signal VSS output in the form of a square wave or a sine wave Use the green white or the yellow wire depending on VSS type See Tabl e2 on pag e5 Connect to a circuit which carries the signal that drives the odometer Special attention must be given to the vehicle speed sensor VSS connection For vehicles with a digital signal square wave TTL co
5. and the gyroscope Verify the VSS connection Make sure that the vehicle icon is moving 2 After a few miles of driving verify that the vehicle icon position is close to the actual vehicle position Make several turns and verify that the system recognizes them 3 The system is now ready for use Please remember that the system is rough calibrated and that over the next 30 miles of driving the system will fine tune its calibration
6. nnecting to the green white striped wire will provide a proper signal In some vehicles e g certain Ford Lincoln Mercury the vehicle speed signal comes from a variable reluctance sensor which has a sine wave output Connecting to the yellow wire will provide a proper signal Some vehicles do not have a speed signal that is available to NavMate e g most vehicles built before 1982 and vehicles with speed signal carried on a bus Please call 1 86NAVMATE1 1 866 286 2831 for these vehicles 2 Route the video cable between the controller mounting location and the display mounting location NOTE Right angle connector mates to the controller TABLE 2 Signal Power 99999 QOOOOHOLO CONTROLLER CONNECTOR WIRE HARNESS VIEW Typical No Signal Power Wire Color Requirements location 1 Ground battery minus Black battery minus Chassis 2 Reverse gear signal Light Green 13 8V DC nominal when vehicle in reverse Backup Low level voltage VL max 1 0 VL min light High level voltage VH min 7 0 VH min 3 Ignition signal Pink 13 8V DC nominal when ignition on Fuse Low level voltage VL max 1 0 VL min block High level voltage VH min 7 0 VH min 4 Vehicle speed signal Yellow Input pulse frequency OHz to 2 5 KHz PCM sine wave Input voltage range 13 to 26 Vmax Low level voltage VL max
Download Pdf Manuals
Related Search