Honeywell W8600A User's Manual
Contents
1. ElectronicAirCleaners com Honeywell W8600A AIRWATCH Indicator APPLICATION The W8600A is available for use with Honeywell media or electronic air cleaners The W8600A function indicator panel has four liquid crystal display LCD arrowheads that point to Battery Air Cleaner UV Air Treatment and Humidifier See Fig 1 A blinking arrowhead indicates service is needed A AIRWA CH fattery LCD Air Cleaner UV Air Treatment Humidifier Honeywell com yourhome FUNCTION INDICATOR PANEL Ge J RESET BUTTON M14696 Fig 1 W8600A AIRWATCH Indicator features INSTALLATION Location The W8600A is designed to blend with the latest T8600 family of Honeywell Chronotherm IV Thermostats The W8600A can also be mounted at any other convenient location in the living area of the home See Fig 2 U S Registered Trademark Copyright 2000 Honeywell H e All Rights Reserved INSTALLATION INSTRUCTIONS M14697 Fig 2 W8600A mounting location Mounting These mounting instructions assume that the W8600A is mounted next to a T8600 Thermostat When installing at another location modify the procedure to fit the installation 1 Remove the W8600A from the base 2 Mark the holes for the mounting screws provided using the base as a template See Fig 3 3 Drill the holes 4 Position the base over the holes and install the screws 5 Tighten the screws un2. is correctly powered needs replacing reset button for 10 b Flashing indicates battery requires replacing seconds or until arrow is no longer displayed Honeywell Home and Building Control Home and Building Control Honeywell 1985 Douglas Drive North Golden Valley MN 55422 69 1448 G H 9 00 Honeywell Limited Honeywell Limit e 35 Dynamic Drive Scarborough Ontario MIV 4Z9 Printed in U S A on recycled paper containing at least 10 post consumer paper fibers www honeywell com your home
3. til the base is mounted firmly on the wall 6 Replace the W8600A onto the base s W6800A BASE A WIRING HOLE MOUNTING HOLES 2 M14695 Fig 3 Using base as mounting template 69 1448 THERMOSTAT L WALLPLATE W8600A AIRWATCH INDICATOR Set DIP Switches 1 Set the DIP switches according to equipment installed in the home a Use default position set at the factory when all devices air cleaner UV air treatment system humidifier are installed in the home b Move DIP switch to left off position when a 1 device is not installed in the home SERVICE The unit beeps every fifteen minutes to indicate an LCD is flashing This means that service or a replacement part is required Replace or service the part corresponding with the LCD flashing 2 Replace the batteries within 30 seconds of removal NOTE to maintain the correct indication time The UV air treatment system and the humidifier settings are for one year The 3 Within 30 seconds after replacing the batteries if air cleaner settings are selectable accord the LCD is blank remove and install new batteries ing to homeowner activities and needs 4 Press and hold the black button on the bottom of the device to reset the timer after servicing or Determine the air cleaner filter run time you desire and set the DIP switches accordingly a If air cleaner filter is used select desired filter time of 3 6 9 or 12 months Follow the set
4. tings on the back of the W8600A to set the DIP switches for the desired number of months b If air cleaner filter is not used move the filter time DIP switches 4 and 5 to the left off replacing parts TROUBLESHOOTING c Use factory default settings to change the nasha cocci aah Ma wash the electronic filter every LCD is beeping Reset by Battery Batteries need Changing batteries 3 changing within 30 seconds of Install Batteries removing old batteries 1 Remove the back cover by pressing in on the tab to maintain correct on the bottom edge top is hinged indication time 2 Install two AAA alkaline batteries provided in the Air Cleaner Media filter needs Pressing and holding harness on the back of the unit replacing or reset button for 10 3 Observe that the W8600A performs a self test electronic filter seconds or until arrow beeping and flashing the LCD display individually needs washing __ is no longer displayed for each device air cleaner UV air treatment sys i z tem humidifier installed in the home UV Air UV lamps need Pressing and holding 4 Press and hold the black reset button on the bot Treatment replacing in UV air reset button for 10 tom of the device for five seconds or until the dis treatment system seconds on until ATOW play stops flashing to start the timers is no longer displayed 5 Observe Battery LCD Humidifier Humidifier pad Pressing and holding a On solidly means unit
Download Pdf Manuals
Related Search