Homelite UT20024B User's Manual
Contents
1. PROBLEM POSSIBLE CAUSE SOLUTION Engine will not start 1 No spark 1 Check spark Remove spark plug Reattach the spark plug cap and lay spark plug on metal cylinder Pull the starter rope and watch for spark at spark plug tip If there is no spark repeat test with a new spark plug 2 No fuel 2 Push primer bulb until bulb is full of fuel If bulb does not fill primary fuel delivery system is blocked Contact a servicing dealer If primer bulb fills engine may be flooded proceed to next item 3 Engine is flooded 3 Remove spark plug turn trimmer so spark plug hole is aimed at the ground Move choke lever to RUN C position and pull starter cord 10 to 15 times This will clear excess fuel from engine Clean and reinstall spark plug Pull starter three times with choke lever at RUN If engine does not start move choke lever to FULL CHOKE A position and repeat normal starting procedure If engine still fails to start repeat procedure with a new spark plug 4 Starter rope pulls harder now than 4 Contact a servicing dealer when new Engine starts but will not Engine requires approximately three Allow engine to completely warm up If engine accelerate minutes to warm up does not accelerate after three minutes contact a servicing dealer Engine starts but will only Carburetor requires adjustment Contact a servicing dealer run at high speed at half choke Engine does not reach full 1 Check oil fuel mixt2. Keep a firm grip with both hands while in operation Trimmer should be held at a com fortable position with the rear handle about hip height Always operate trimmer at full throttle Cut tall grass from the top down This will prevent grass from wrapping around the shaft housing and string head which may cause damage from overheating If grass becomes wrapped around the string head STOP THE ENGINE disconnect the spark plug wire and remove the grass Prolonged cutting at partial throttle will result in oil dripping from the muffler STARTING AND STOPPING See Figures 8 9 Trimmer should be on a flat bare surface for starting mM Slowly press the primer bulb seven 7 times E Set the choke lever to the FULL CHOKE position A mM Squeeze the throttle trigger fully and pull starter handle sharply until engine attempts to run Do not pull the starter handle more than eight 8 times NOTE Keep throttle trigger squeezed fully E Set the choke lever to the HALF CHOKE position B Pull the starter handle until the engine runs Do not pull the starter handle more than six 6 times E Allow the engine to run for 15 seconds then set the choke lever to the RUN position C TO STOP THE ENGINE See Figure 9 To stop the engine push and hold the STOP button until the engine stops IF ASSISTANCE IS REQUIRED FOR THIS PRODUCT Do not return this product to the retail store where it was purchased Please call our Cus
3. and dampness diet smoking and work practices are all thought to contribute to the development of these symptoms It is presently unknown what if any vibrations or extent of exposure may contribute to the condition There are measures that can be taken by the operator to possibly reduce the effects of vibration a Keep your body warm in cold weather When operating the unit wear gloves to keep the hands and wrists warm It is reported that cold weather is a major fac tor contributing to Raynaud s Syndrome b After each period of operation exercise to increase blood circulation c Take frequent work breaks Limit the amount of exposure per day d Keep the tool well maintained fasteners tightened and worn parts replaced If you experience any of the symptoms of this condition immediately discontinue use and see your physician about these symptoms Mix and store fuel in a container approved for gasoline Mix fuel outdoors where there are no sparks or flames Wipe up any fuel spillage Move 9 m 80 ft away from refueling site before starting engine Stop the engine and allow to cool before refueling or storing the unit Allow the engine to cool empty the fuel tank and secure the unit from moving before transporting in a vehicle SPECIFIC SAFETY RULES SPECIFIC SAFETY RULES FOR TRIMMER USE Replace string head if cracked chipped or damaged in any way Be sure the string head or blade is properly installed and se
4. or missing please call CURVED SHAFT GRASS DEFLECTOR WITH PE ene etre aesieenee OUT EDGER GUIDE TRIMLITE AND TRIM N PACKING LIST EDGE Trimmer Assembly See Figure 3 Operator s Kit E Remove wing nut flat washer lock washer and bolt from Front Handle the operator s kit Curved Shaft Grass Deflector Trim n Edge and Trimlite Straight Shaft Grass Deflector Easy Reach m Place curved shaft grass deflector over shaft and bracket E install bolt through the slots in the tabs on grass deflector Edger Guide Trim n Edge and bracket on shaft housing Hardware Bags 2 Trimlite and Easy Reach E Install flat washer lock washer and wing nut Hardware Bags 3 Trim n Edge E Tighten securely Bottle of 2 Cycle Oil Operator s Manual FRONT HANDLE Bee GE ATS EOS VES Sy s ie ar taal t cS A NF TA Cee eae e fh ssp eS tat os A WARNING If any parts are missing do not operate this tool until the missing parts are replaced Failure to do so could result in possible serious personal injury A WARNING Do not attempt to modify this tool or create accesso ries not recommended for use with this tool Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal Injury DEFLECTOR A WARNING To prevent accidental starting that could cause serious personal injury always disconnect the engine spark plug wire from the spark plug w
5. the drive shaft near the gear head m Place the mounting bracket over the drive shaft so the square tab on the mounting bracket fits into the slot in the straight shaft grass deflector E Rotate the mounting bracket so the screw on the grass deflector goes into the slot on the mounting bracket E Install the wing nut and tighten securely LOCATOR HOLE WING NUT MOUNTING BRACKET DEFLECTOR OPERATION AY WARNING Do not allow familiarity with tools to make you care less Remember that a careless fraction of a second is sufficient to inflict serious injury A WARNING Always wear safety goggles or safety glasses with side shields when operating tools Failure to do so could result in objects being thrown into your eyes resulting in possible serious injury A WARNING Do not use any attachments or accessories not recom mended by the manufacturer of this tool The use of attachments or accessories not recommended can result in serious personal injury FUELING AND REFUELING THE TRIMMER FUEL MIXTURE This product is powered by a 2 cycle engine and requires pre mixing gasoline and 2 cycle oil Pre mix unleaded gasoline and 2 cycle engine oil in a clean 1 gallon container approved for gasoline Recommended fuel This engine is certified to operate on unleaded gasoline intended for automotive use Mix Homelite Premium Exact Mix oil with gasoline according to the instructions on the package If Premium Ex
6. Be sure to provide all relevant information when you call or visit Forthe location of the authorized service dealer nearest you please call 1 800 242 4672 or visit us online at www homelite com REPAIR PARTS The model number of this tool is found on a plate or label attached to the housing Please record the serial number in the space provided below MODEL NUMBER SERIAL NUMBER HOMELITE CONSUMER PRODUCTS INC 1428 Pearman Dairy Road Anderson SC 29625 Post Office Box 1207 Anderson SC 29622 Phone 1 800 242 4672 www homelite com 983000 771 4 05
7. EPHONE OR TELEGRAM CHARGES RENTAL OF A LIKE PRODUCT DURING THE TIME WARRANTY SERVICE IS BEING PERFORMED TRAVEL LOSS OR DAMAGE TO PERSONAL PROPERLY LOSS OF REVENUE LOSS OF USE OF THE PRODUCT LOSS OF TIME OR INCONVENIENCE SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU This warranty gives you specific legal rights and you may also have other rights which vary from state to state This warranty applies to all HOMELITE products manufactured by HOMELITE and sold in the United States and Canada To locate your nearest service dealer dial 1 800 242 4672 or log on to our website at www homelite com Page 19 WARRANTY THE FOLLOWING CALIFORNIA AIR RESOURCES BOARD CARB STATEMENT ONLY APPLIES TO MODEL NUMBERS REQUIRED TO MEET THE CARB REQUIREMENTS HOMELITE CONSUMER PRODUCTS INC LIMITED WARRANTY FEDERAL AND CALIFORNIA EMISSION CONTROL SYSTEMS NONROAD AND SMALL OFF ROAD ENGINES The U S Environmental Protection Agency EPA the California Air Resources Board CARB and Homelite Consumer Products Inc are pleased to explain the Emission Control System Warranty on your nonroad or small off road engine In California new small off road engines must be designed built and equipped to meet the state s stringent anti smog standards In other states new 2000 and later model year nonroad engines must be designed built and equipped at t
8. HT SHAFT GRASS DEFLECTOR STRING HEAD KNOW YOUR STRING TRIMMER See Figures 1a 1b Before attempting to use this product familiarize yourself with all operating features and safety rules ERGONOMIC DESIGN The design of the trimmer provides for easy handling It is designed for comfort and ease of grasp when operating in different positions and at different angles GRASS DEFLECTOR The trimmer includes a grass deflector that helps protect you from flying debris TOP MOUNTED MOTOR The top mounted motor improves balance and is located away from the dust and debris of the cutting area EZ LINE TAP ADVANCE SYSTEM The EZ Line Tap Advance System allows easy line advance during trimmer operation Page 7 ASSEMBLY UNPACKING FRONT HANDLE This product requires assembly See Figure 2 E Carefully remove the tool and any accessories from the Remove the front handle bolt and wing nut from the box Make sure that all items listed in the packing list are operator s kit included E Install the front handle onto the top side of the drive shaft E Inspect the tool carefully to make sure no breakage or housing and move it to a comfortable position damage occurred during shipping E Place the bolt through the front handle as shown then E Do not discard the packing material until you have care install the wing nut fully inspected and satisfactorily operated the tool Tighten wing nut securely E f any parts are damaged
9. In addition this warranty does not cover A Tune ups Spark Plugs Carburetor Carburetor Adjustments Ignition Filters B Wear items Bump Knobs Outer Spools Cutting Lines Inner Reels Starter Pulleys Starter Ropes Drive Belts Tines Felt Washers Hitch Pins Mulching Blades Blower Fans Blower and Vacuum Tubes Vacuum Bags and Straps Guide Bars Saw Chains HOMELITE reserves the right to change or improve the design of any HOMELITE product without assuming any obligation to modify any product previously manufactured ALL IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE STATED WARRANTY PERIOD ACCORDINGLY ANY SUCH IMPLIED WARRANTIES INCLUDING MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE ARE DISCLAIMED IN THEIR ENTIRETY AFTER THE EXPIRATION OF THE APPROPRIATE TWO YEAR ONE YEAR OR NINETY DAY WARRANTY PERIOD HOMELITE S OBLIGATION UNDER THIS WARRANTY IS STRICTLY AND EXCLUSIVELY LIMITED TO THE REPAIR OR REPLACEMENT OF DEFECTIVE PARTS AND HOMELITE DOES NOT ASSUME OR AUTHORIZE ANYONE TO ASSUME FOR THEM ANY OTHER OBLIGATION SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU HOMELITE ASSUMES NO RESPONSIBILITY FOR INCIDENTAL CONSEQUENTIAL OR OTHER DAMAGES INCLUDING BUT NOT LIMITED TO EXPENSE OF RETURNING THE HOMELITE PRODUCT TO AN AUTHORIZED SERVICE DEALER AND EXPENSE OF DELIVERING IT BACK TO THE OWNER MECHANIC S TRAVEL TIME TEL
10. RANTY THIS PRODUCT WAS MANUFACTURED WITH A CATALYST MUFFLER Congratulations You have made an investment toward protecting the environment In order to maintain this product s original emission level please refer to the maintenance section below EMISSIONS MAINTENANCE SCHEDULE AND WARRANTED PARTS LIST Emissions Parts Inspect Before Clean Every Replace Clean Every Replace Every Each Use 5 Hours Every 25 Hours 25 Hours 50 Hours or Yearly or Yearly CATALYTIC MUFFLER ASSEMBLY AIR FILTER ASSY includes Filter SPARK SCREEN CARBURETOR ASSY includes Heat Dam Gaskets FUEL TANK ASSY includes Fuel Lines Fuel Cap Fuel Filter IGNITION ASSY includes Spark Plug ALL EMISSIONS RELATED PARTS ARE WARRANTED FOR TWO YEARS OR FOR THE PERIOD OF TIME PRIOR TO THE PARTS FIRST SCHEDULED REPLACEMENT WHICHEVER COMES FIRST CALL US FIRST For any questions about operating or maintaining your product call the Homelite Help Line Your product has been fully tested prior to shipment to ensure your complete satisfaction Page 21 OPERATOR S MANUAL 25cc String Trimmers Trimlite UT20004B Trim n Edge UT20024B Easy Reach UT20044B A WARNING The engine exhaust from this product contains chemicals known to the State of California to cause cancer birth defects or other reproductive harm CALIFORNIA PROPOSITION 65 SERVICE For parts or service contact your nearest Homelite authorized service dealer
11. Trim n Edge model UT20024B OPERATOR S MANUAL 25cc String Trimmers Trimlite model UT20004B Easy Reach model UT20044B Your trimmer has been engineered and manufactured to Homelite s high standard for dependability ease of operation and operator safety Properly cared for it will give you years of rugged trouble free performance A WARNING To reduce the risk of injury the user must read and understand the operator s manual before using this product Thank you for buying a Homelite product SAVE THIS MANUAL FOR FUTURE REFERENCE TABLE OF CONTENTS HEY FCO CUI OUT ae eaea Ene EEEE E EEE sceneries trac E AAE EE EAEE A E A A 2 General ately RUIS aeisi engein EnEn e EE Oe EEN EREEREER aE ENARE ONE ENEE 3 SPECIE UY PS acne sree ere ete cee ccs E ovsedecctainosseng oie e a tase lt esseneeento tueeeidaactene 3 MOON aaen EI E A EE E E E E A EE E E E E E 4 5 FOTU a E E E E cudnt tant coietnneteanetinvtaleiadamesinievatsenesaneies 6 7 PSS SOU a a E T T T curated qussiutei codeabestssanumee tons 8 10 DT OIA aea a te ee aan date tts esd ance ue eho E EE sale EE E E auandeadianeentoassuinet ua EE E E 10 13 MAIMON O e oneielosieecncts atane boomed aoomnnnstonsat and venskntastent ster pein slau eadateiy phan nstunsieecctmisimnunaietsan eden iehanagenencots 14 16 TOUTS SAO OC aero antes ett prance dota eeatds aa a 17 18 W ore core E cite nins E A E sendin iaoeattetvand dodwise ney E E E A E 19 21 Parts Ordening 7 Se WIG
12. act Mix oil is not available use a high quality 2 cycle engine oil mixed at 2 6 oz per gallon US Do not use automotive oil or 2 cycle outboard oil NOTE Premium Exact Mix fuel mix will stay fresh up to 30 days DO NOT mix quantities larger than usable in a 30 day period PREMIUM EXACT MIX 50 1 EJ GASOLINE OIL 1 gallon US 2 6 Oz 20 cc 20 ml 1 Liter Page 10 OPERATION FILLING TANK E Clean surface around fuel cap to prevent contamination m Loosen fuel cap slowly Rest the cap on a clean surface E Carefully pour fuel into the tank Avoid spillage E Prior to replacing the fuel cap clean and inspect the gasket E Immediately replace fuel cap and hand tighten Wipe up any fuel spillage NOTE It is normal for smoke to be emitted from a new engine after first use A WARNING Always shut off engine before fueling Never add fuel to a machine with a running or hot engine Move at least 30 ft 9 m from refueling site before starting engine Do not smoke OPERATING THE TRIMMER See Figure 8 A WARNING Always position the unit on the operator s right side The use of the unit on the operator s left side will expose the user to hot surfaces and can result in possible burn injury A WARNING To avoid burns from hot surfaces never operate unit with the bottom of the engine above waist level Hold the trimmer with your right hand on the rear handle and your left hand on the front handle
13. curely fastened Failure to do so can cause serious injury Make sure all guards straps deflectors and handles are properly and securely attached Use only the manufacturer s replacement string in the cutting head Do not use any other cutting attachment Page 3 To install any other brand of cutting head to this string trimmer can result in serious personal injury Never operate unit without the grass deflector in place and in good condition Maintain a firm grip on both handles while trimming Keep string head below waist level Never cut with the string head located over 76 cm 80 in or more above the ground SYMBOLS Some of the following symbols may be used on this tool Please study them and learn their meaning for safe operation of this product SYMBOL NAME EXPLANATION Safety Alert Symbol Precautions that involve your safety To reduce the risk of injury user must read and under Read the Operator s Manual stand operator s manual before using this product Wear eye protection which is marked to comply with Wear Eye and Hearing Protection ANSI Z87 1 as well as hearing protection when oper ating this equipment Keep Bystanders Away Keep all bystanders at least 50 ft 15 m away Ricochet Thrown objects can ricochet and result in personal injury or property damage No Blade Do not install or use any type of blade on a product displaying this symbol Use unleaded gasoline intended for motor vehicle use w
14. e keep air filter clean E Remove the air filter cover by pushing down on the latch with your thumb while gently pulling on the cover E Remove the filter clean it in warm soapy water Rinse and let dry completely For best performance replace annually m Install the filter align tabs push in and make sure the latch snaps and latches into place PULL COVER FUEL CAP Ja TO OPEN A WARNING A leaking fuel cap is a fire hazard and must be replaced immediately The fuel cap contains a non serviceable filter and a check valve A clogged fuel filter will cause poor engine perfor mance If performance improves when the fuel cap is loos ened check valve may be faulty or filter clogged Replace fuel cap if required SPARK PLUG This engine uses a NGK BPMR7A spark plug with 025 in 0 63 mm electrode gap Use an exact replacement and replace annually or more frequently if necessary STORING THE TRIMMER 1 MONTH OR LONGER E Drain all fuel from tank into a container approved for gasoline Run engine until it stops AIR FILTER E Clean all foreign material from the trimmer Store it in a well ventilated place that is inaccessible to children Keep away from corrosive agents such as garden chemicals and de icing salts E Abide by all Federal and local regulations for the safe storage and handling of gasoline Excess fuel should be used up in other 2 cycle engine powered equipment Page 16 TROUBLESHOOTING
15. ents caused by the failure of a warranted part still under warranty The California Air Resources Board s Emission Warranty Parts List specifically defines the emission related warranted parts EPA s regulations do not include a parts list but EPA considers emission related warranted parts to include all the parts listed below These warranted parts are Carburetor Spark Plug Ignition Air Filter and Fuel Filter MAINTENANCE REQUIREMENTS The operator is responsible for the performance of the required maintenance as defined by Homelite Consumer Products Inc in the operator s manual LIMITATIONS The Emission Control Systems Warranty shall not cover any of the following a repair or replacement required because of misuse or neglect lack of required maintenance repairs improperly performed or replacements not conforming to Homelite Consumer Products Inc specifications that adversely affect performance and or durability and alterations or modifications not recommended or approved in writing by Homelite Consumer Products Inc and b replacement of parts and other services and adjustments necessary for required maintenance at and after the first scheduled replacement point The Emissions Compliance Period referred to on the Emissions Compliance label indicates the number of operating hours for which the engine has been shown to meet Federal emission requirements Category C 50 hours B 125 hours and A 300 hours Page 20 WAR
16. gine owner you are responsible for the performance of required maintenance listed in your operator s manual Homelite Consumer Products Inc recommends that you retain all receipts covering maintenance on your nonroad or small off road engine but Homelite Consumer Products Inc cannot deny warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance Any replacement part or service that is equivalent in performance and durability may be used in non warranty maintenance or repairs and shall not reduce the warranty obligations of the engine manufacturer b As the nonroad or small off road engine owner you should be aware however that Homelite Consumer Products Inc may deny you warranty coverage if your nonroad or small off road engine or a part has failed due to abuse neglect improper maintenance or unapproved modifications c You are responsible for presenting your nonroad or small off road engine to a Homelite Consumer Products Inc service dealer as soon as a problem exists The warranty repairs should be completed in a reasonable amount of time not to exceed 30 days If you have any questions regarding your warranty rights and responsibilities you should contact a Homelite Consumer Products Inc Customer Representative at 1 800 242 4672 COVERAGE Homelite Consumer Products Inc warrants to the ultimate purchaser and each subsequent purchaser that your nonroad or small off
17. he strings and pull sharply to release them from the slots in the spool Push down and turn the spool counterclockwise until it no longer turns Hold the spool down and rotate clockwise a small amount Release the spool The spool should be locked down in the string head If not hold down and rotate until locked Make sure the string head and the spool retainer are installed on the drive shaft MAINTENANCE To install the spool retainer Turn the spool retainer clockwise for Trimlite and Trim n Edge Turn the spool retainer counterclockwise for Easy Reach Pull the strings again to rotate the spool into cutting position Push the spool retainer down while pulling on string s to manually advance the string and to check for proper assembly of the string head STRING REPLACEMENT See Figures 16 19 E Stop the engine and disconnect the spark plug wire Hold the string head and unscrew the spool retainer To remove the spool retainer Turn the spool retainer counterclockwise for Trimlite and Trim n Edge Turn the spool retainer clockwise for Easy Reach E Remove the spool from the string head NOTE Keep the spring attached to the spool Remove any old string remaining on the spool Cut two pieces of string each being approximately 9 ft 2 7 m long Use only 080 in 2 0 mm diameter mono filament string E Insert the first string into the anchor hole in the upper part of the spool Wind the first string a
18. he time of sale to meet the U S EPA regula tions for small nonroad engines The nonroad engine must be free from defects in materials and workmanship which cause it to fail to conform with U S EPA standards for the first two years of engine use from the date of sale to the ultimate purchaser Homelite Consumer Products Inc must warrant the emission control system on your nonroad or small off road engine for the period of time listed above provided there has been no abuse neglect or improper maintenance of your nonroad or small off road engine Your emission control system may include parts such as the carburetor or fuel injection system the ignition system and the catalytic converter Also included may be hoses belts and connectors and other emission related assemblies Where a warrantable condition exists Homelite Consumer Products Inc will repair your nonroad or small off road engine at no cost to you including diagnosis if the diagnostic work is performed at an authorized dealer parts and labor MANUFACTURER S WARRANTY COVERAGE The 1995 and later small off road engines are warranted for two years in California In other states 1997 and later model year non road engines are also warranted for two years If any emission related part on your engine is defective the part will be repaired or replaced by Homelite Consumer Products Inc free of charge OPERATOR S WARRANTY RESPONSIBILITIES a As the nonroad or small off road en
19. hen assembling parts BRACKET WASHER KK WING NUT Fig 3 WASHER Page 8 ASSEMBLY CURVED SHAFT GRASS DEFLECTOR WITH EDGER GUIDE TRIM N EDGE ONLY EDGER GUIDE ASSEMBLY i WING NUT See Figure 4 K m Assemble the two plastic pieces of the edger guide together using the short bolt flat washer lock washer LOCK and wing nut WASHER ia length EDGER GUIDE E Slide the edger guide to adjust it to the desired trimming PIECES hy E Tighten the wing nut securely CURVED SHAFT GRASS DEFLECTOR WITH EDGER GUIDE TRIM N EDGE ONLY See Figures 5 6 E Remove the wing nut flat washer lock washer and bolt from the Operator s Kit FLAT WASHER E Place the curved shaft grass deflector over the shaft and bracket E Slide the assembled edger guide over the tabs on the grass deflector and bracket E Place the bolt through the slots in the tabs on the grass deflector and trimmer NOTE Ensure the slots are aligned before installing the bolt E Install the flat washer lock washer and wing nut E Tighten the wing nut securely ASSEMBLED EDGER GUIDE WING NUT a LOCK a i WASHER FLAT WASHER Page 9 ASSEMBLY STRAIGHT SHAFT GRASS DEFLECTOR EASY REACH See Figure 7 E Remove the wing nut and clamp from the grass deflector E Assemble straight shaft grass deflector to drive shaft so that the pin in the grass deflector fits in the locator hole in the lower side of
20. hich can glasses with side shields or a full face shield when needed We recommend Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side shields Always use eye protection which is marked to comply with ANSI 287 1 result in severe eye damage Before beginning power tool operation always wear safety goggles safety a SAVE THESE INSTRUCTIONS Page 5 FEATURES Weight without fuel Bia an UE EE A E EET E EOE E E EA EEA T EE AATE AE EE A N 9 6 Ibs 4 4 kg AES UGGS spaa AE E a ia E E EE E EAE EE EE A 10 Ibs 4 5 kg Ee lg cc E pA EN S PO AI TAN OEA AE TE AAEE ee ee PENE ETA A EEA 10 6 Ibs 4 8 kg E CUNT O a E E E E N O 17 in 432 mm ECU CSI eE A EE EEE EOE EE E EN E EE E I N E 250C NEE ae aE E A E vedantmavaciesateatwedatuen dune catioendennenens 080 in 2 0 mm TRIMLITE MODEL PRIMER BULB STARTER GRIP CHOKE LEVER FRONT HANDLE STOP BUTTON DRIVE SHAFT REAR HOUSING HANDLE THROTTLE TRIGGER CURVED SHAFT TRIM N EDGE MODEL GRASS DEFLECTOR i PRIMER I oe LAY oa Ger BULB T STRING AAN CHOKE LEVER HEAD STARTER GRIP STOP BUTTON FRONT HANDLE REAR HANDLE DRIVE SHAFT HOUSING THROTTLE TRIGGER CURVED SHAFT GRASS DEFLECTOR EDGER ATTACHMENT TRIM N EDGE ONLY STRING HEAD SI Fig la FEATURES EASY REACH MODEL STARTER GRIP FRONT HANDLE DRIVE SHAFT HOUSING PRIMER BULB CHOKE LEVER STOP BUTTON REAR HANDLE THROTTLE TRIGGER STRAIG
21. ith an octane rating of 87 R M 2 or higher This product is powered by a 2 cycle engine and requires pre mixing gasoline and 2 cycle oil Gasoline and Oil Page 4 SYMBOLS The following signal words and meanings are intended to explain the levels of risk associated with this product SYMBOL SIGNAL MEANING A DANGER Indicates an imminently hazardous situation which if not avoided will result in death or serious injury 1 WARNING Indicates a potentially hazardous situation which if not avoided could result in death or serious injury CAUTION Indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury CAUTION Without Safety Alert Symbol Indicates a situation that may result in property damage SERVICE Servicing requires extreme care and knowledge and should A WARNING be performed only by a qualified service technician For service we suggest you return the product to your nearest AUTHORIZED SERVICE CENTER for repair When servic ing use only identical replacement parts To avoid serious personal injury do not attempt to use this product until you read thoroughly and understand completely the operator s manual Save this operator s manual and review frequently for continuing safe opera tion and instructing others who may use this product A WARNING The operation of any power tool can result in foreign objects being thrown into your eyes w
22. ke fluids gasoline petroleum based products penetrating oils etc come in contact with plastic parts Chemicals can damage weaken or destroy plastic which may result in serious personal injury You can often make adjustments and repairs described here For other repairs have the trimmer serviced by an authorized service dealer SPOOL REPLACEMENT EZ LINE TAP ADVANCE SYSTEM NEW PREWOUND SPOOL See Figures 14 15 If replacing string only refer to String Replacement later in this manual Use only 080 in 2 0 mm diameter monofilament string Use original manufacturer s replacement string for best performance E Stop the engine and disconnect the spark plug wire Hold the string head and unscrew the spool retainer To remove the spool retainer Turn the spool retainer counterclockwise for Trimlite and Trim n Edge Turn the spool retainer clockwise for Easy Reach Page 14 SPOOL RETAINER SPRING Remove the empty spool from the string head Keep the spring attached to the spool To install the new spool make sure the two strings are captured in the slots opposite each other on the new spool Make sure the end of each string is extended ap proximately 6 in beyond each slot Thread the strings into the eyelets in the string head Carefully push the spool into the string head gently pull the strings to the outside if necessary When the spool is positioned in the string head grasp t
23. n threads and lubricate with grease if no improvement replace the spool retainer 1 Cut tall grass from the top down to prevent wrapping 2 Operate trimmer at full throttle 1 Operate trimmer at full throttle 2 Use fresh fuel and the correct 2 cycle oil mix 3 Clean per instruction in Maintenance Section IDLE SPEED WARRANTY LIMITED WARRANTY STATEMENT Homelite Consumer Products Inc warrants to the original retail purchaser that this HOMELITE product is free from defect in material and workmanship and agrees to repair or replace at Homelite Consumer Products Inc s discretion any defective product free of charge within these time periods from the date of purchase E One year for the following units Yard Broom Trimlite and Bandit E Two years for all other Homelite products ifthe product is used for personal family or household use E 90 days if any of the above products are used for any other purpose such as commercial or rental This warranty extends to the original retail purchaser only and commences on the date of the original retail purchase Any part of the HOMELITE product manufactured or supplied by HOMELITE and found in the reasonable judgment of HOMELITE to be defective in material or workmanship will be repaired or replaced by an authorized HOMELITE service dealer without charge for parts and labor The HOMELITE product including any defective part must be returned to an authorized se
24. oduct Wear heavy long pants boots and gloves Do not wear loose fitting clothing short pants or go barefoot Do not wear jewelry of any kind Product users on United States Forest Service land and in some states must comply with fire prevention regu lations This product is equipped with a spark arrestor however other user requirements may apply Check with your federal state or local authorities Never operate this unit on the operator s left side Secure long hair above shoulder level to prevent entan glement in moving parts Keep all bystanders children and pets atleast 50 ft away Do not operate this unit when you are tired ill or under the influence of alcohol drugs or medication Do not operate in poor lighting Keep firm footing and balance Do not overreach Over reaching can result in loss of balance or exposure to hot surfaces To avoid hot surfaces never operate the unit with the bottom of the engine above waist level carburetor adjustments Inspect the unit before each use for loose fasteners fuel leaks etc Replace any damaged parts before use The string head or blade will rotate during carburetor adjustments It has been reported that vibrations from hand held tools may contribute to acondition called Raynaud s Syndrome in certain individuals Symptoms may include tingling numbness and blanching of the fingers usually apparent upon exposure to cold Hereditary factors exposure to cold
25. r in this manual for additional information E The edger guide allows the trimmer to be used as an edger for cutting along sidewalks driveways flower beds etc The edger guide is convenient to use and supports the trimmer as it is being used as an edger E Be extremely careful when tilting the trimmer to use as an edger The muffler and the exhaust from the muffler get very hot during operation Keep the muffler away from all body parts Fig 12 PROPER OPERATING POSITION wt M pee ne ied i ore err Vp Wey NY N i ee R we a Nyy POA ARS mee MAINTENANCE A WARNING When servicing use only identical Homelite replacement parts Use of any other parts may create a hazard or Cause product damage A WARNING Always wear safety goggles or safety glasses with side shields during tool operation If operation is dusty also wear a dust mask A WARNING Before inspecting cleaning or servicing the machine shut off engine wait for all moving parts to stop and disconnect spark plug wire and move it away from spark plug Failure to follow these instructions can result in serious personal injury or property damage GENERAL MAINTENANCE Avoid using solvents when cleaning plastic parts Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use Use clean cloths to remove dirt dust oil grease etc A WARNING Do not at any time let bra
26. road engine will be designed built and equipped at the time of sale to meet all applicable regulations Homelite Consumer Products Inc also warrants to the initial purchaser and each subsequent purchaser that your nonroad or small off road engine is free from defects in materials and workmanship which cause the engine to fail to conform with applicable regulations for a period of two years The 1995 and later small off road engines are warranted for two years in California In all other states for 1997 and later model years EPA requires manufacturers to warrant non road engines for two years These warranty periods will begin on the date the nonroad or small off road engine is purchased by the initial purchaser If any emission related part on your engine is defective the part will be replaced by Homelite Consumer Products Inc at no cost to the owner Homelite Consumer Products Inc shall remedy warranty defects at any authorized Homelite Consumer Products Inc engine dealer or warranty station Any authorized work done at an authorized dealer or warranty station shall be free of charge to the owner if such work determines that a warranted part is defective Any manufacturer approved or equivalent replacement part may be used for any warranty maintenance or repairs on emission related parts and must be provided free of charge to the owner if the part is still under warranty Homelite Consumer Products Inc is liable for damages to other engine compon
27. round the upper part of the spool counterclockwise as shown by the arrows on the spool Place string in the slot on upper spool flange leaving about 6 in 152 mm extended beyond the slot Do not overfill After winding the string there should be at least 1 4 in 6 mm between the wound string and the outside edge of the spool E Repeat above step with second string using the bottom part of spool Do not overfill E Replace the spool and the spool retainer Refer to Spool Replacement earlier in this manual CLEANING THE EXHAUST PORT AND MUFFLER NOTE Depending on the type of fuel used the type and amount of oil used and or your operating conditions the exhaust port and muffler may become blocked with carbon deposits If you notice a power loss with your gas powered tool you may need to remove these deposits to restore performance We highly recommended that only qualified service technicians perform this service SPARK ARRESTOR The muffler is equipped with a spark arrestor screen inside the muffler body Through normal use the screen can be come dirty and should be periodically cleaned or replaced by an anthorized service dealer Page 15 s SPRING x gt lt PER s SONNE ih a SEEN SSE ARROWS ON SPOOL ANCHOR A HOLE FIRST STRING FIRST STRING SLOT SECOND STRING MAINTENANCE REPLACING AND CLEANING AIR FILTER See Figures 20 21 For proper performance and long lif
28. rvice dealer within the warranty period The expense of delivering the HOMELITE product to the dealer for warranty work and the expense of returning it back to the owner after repair or replacement will be paid by the owner HOMELITE S responsibility in respect to claims is limited to making the required repairs or replacements and no claim of breach of warranty shall be cause for cancellation or rescission of the contract of sale of any HOMELITE product Proof of purchase will be required by the dealer to substantiate any warranty claim All warranty work must be performed by an authorized HOMELITE service dealer This warranty is limited to ninety 90 days from the date of original retail purchase for any HOMELITE product that is used for rental or commercial purposes or any other income producing purpose This warranty does not cover any HOMELITE product that has been subject to misuse neglect negligence or accident or that has been operated in any way contrary to the operating instructions as specified in the HOMELITE operator s manual This warranty does not apply to any damage to the HOMELITE product that is the result of improper maintenance or to any HOMELITE product that has been altered or modified The warranty does not extend to repairs made necessary by normal wear or by the use of parts or accessories which are either INCOMPATIBLE WITH THE HOMELITE product or adversely affect its operation performance or durability
29. serieen EAEra aE E Ee R ESEE e OEREO EEE EEE AIRES ROR SENERARE EaSI 22 INTRODUCTION This tool has many features for making its use more pleasant and enjoyable Safety performance and dependability have been given top priority in the design of this product making it easy to maintain and operate Page 2 GENERAL SAFETY RULES E Keep all parts of your body away from any moving part A WARNING E Do not touch area around the muffler or cylinder of the unit these parts get hot from operation m Always stop the engine and remove the spark plug wire before making any adjustments or repairs except for Read and understand all instructions Failure to follow all instructions listed below may result in electric shock fire and or serious personal injury READ ALL INSTRUCTIONS For safe operation read and understand all instructions before using this product Follow all safety instructions Failure to follow all safety instructions listed below can result in serious personal injury Do not allow children or untrained individuals to use this unit Never start or run the engine in a closed or poorly venti lated area breathing exhaust fumes can kill Clear the work area before each use Remove all objects such as rocks broken glass nails wire or string which can be thrown or become entangled in the cutting line or blade Wear safety glasses or goggles that are marked to comply with ANSI Z87 1 standard when operating this pr
30. tain best performance and keep string long enough to advance properly CUTTING TIPS See Figure 11 E Avoid hot surfaces by always keeping the tool away from your body Proper operating position shown in figure 10 E Keep the trimmer tilted toward the area being cut this is the best cutting area E The curved shaft trimmer cuts when passing the unit from right to left The straight shaft trimmer cuts when passing the unit from left to right This will avoid throwing debris at the operator Avoid cutting in the dangerous area shown in Figure 11 E Use the tip of string to do the cutting do not force string head into uncut grass E Wire and picket fences cause extra string wear even breakage Stone and brick walls curbs and wood may wear string rapidly E Avoidtrees and shrubs Tree bark wood moldings siding and fence posts can easily be damaged by the string PROPER OPERATING POSITION f se N i i E We OC Q EA A l NEA lt S J A NKI j VN iN IA Y l Fig 10 i DANGEROUS CUTTING AREA DIRECTION OF ROTATION SoS est CUTTING area M EASY REACH DANGEROUS CUTTING AREA DIRECTION OF BEST CUTTING AREA ROTATION Page 12 OPERATION EDGER GUIDE OPERATION TRIM N EDGE ONLY See Figures 12 13 m Loosen the wing nut and slide the edger guide to adjust WING NUT it to the desired trimming length then retighten the wing nut securely Refer to Edger Guide Assembly earlie
31. tomer Service Department for any issues you may have For Help Call 1 800 242 4672 PRIMER AN A RS IN d ERZ STARTING INSTRUCTION LABEL THROTTLE TRIGGER PRIMER BULB zz CEEE T S Fig 9 Page 11 OPERATION A WARNING Always hold the string trimmer away from the body keep ing clearance between the body and the product Any contact with the housing or string trimmer cutting head can result in burns and or other serious personal injury ADVANCING STRING USING THE EZ LINE TAP ADVANCE SYSTEM String advance is controlled by tapping string head on grass while running engine at full throttle E Run engine at full throttle E Tap string head on ground to advance string String ad vances each time the head is tapped E Several taps may be required until string strikes the cut off blade E Resume trimming NOTE If the string is worn too short you may not be able to advance the string by tapping it on the ground If so STOP THE ENGINE and manually advance the string ADVANCING THE STRING MANUALLY Push the spool retainer down while pulling on string s to manually advance the string CUT OFF BLADE This trimmer is equipped with a cut off blade on the grass deflector For best cutting advance string until it is trimmed to length by the cut off blade Advance string whenever you hear the engine running faster than normal or when trimming efficiency diminishes This will main
32. ure 1 Use fresh fuel and the correct 2 cycle oil mix speed and emits excessive 2 Air filter is dirty 2 Clean air filter Refer to Replacing and Clean smoke ing Air Filter earlier in this manual 3 Spark arrestor screen is dirty 3 Contact a servicing dealer Engine starts runs and ac Turn idle speed screw clockwise to increase idle celerates but will not idle Idle speed screw on carburetor needs speed adjustment Page 17 TROUBLESHOOTING PROBLEM String will not advance when using the EZ Line tap advance system Spool retainer hard to turn when using EZ Line tap advance system Grass wraps around drive shaft housing and string head Oil drips from muffler POSSIBLE CAUSE 1 String is welded to itself 2 Not enough string on spool 3 String is worn too short 4 String is tangled on spool 5 Engine speed is too slow Screw threads are dirty or damaged 1 Cutting tall grass at ground level 2 Operating trimmer at part throttle 1 Operating trimmer at part throttle 2 Check oil fuel mixture 3 Air filter dirty Page 18 SOLUTION o_o Lubricate with silicone spray 2 Install more string Refer to String Replace ment earlier in this manual 3 Pull strings while alternately pressing down on and releasing spool retainer 4 Remove string from spool and rewind Refer to String Replacement earlier in this manual 5 Advance string at full throttle Clea
Download Pdf Manuals
Related Search