Hoist Fitness HS1225 User's Manual
Contents
1. 0056 HS1225 LOW BACK SS Note Both Serial Number and Model Number Required when Ordering Parts Customer Service 800 548 5438 858 578 7676 RECORD SERIAL NUMBER HERE TIVOINVIA SHANMO 858 578 9558 OWNERS MANUAL CONTENTS INSTRUCTIONS Step 1 FRAME ASSEMBLY Step 2 PRE ASSEMBLY PART LISTING GENERAL MAINTENANCE INFORMATION LIMITED WARRANTY Page 1 275 7 51225 Assembly OWNERS MANUAL Step 1 INSTRUCTIONS Before beginning assembly please take the time to read the instructions thoroughly Please use the various lists in this manual to make sure that all parts have been included in your shipment When ordering use the part number and description from the lists Use only Hoist replacement parts when servicing Failure to do so will void your warranty and could result in personal injury Hoist equipment is designed to provide the smoothest most effective exercise motion possible After assembly you should check all functions to ensure correct operation If you experience problems first recheck the assembly instructions to locate any possible errors made during assembly If you are unable to correct the problem call your authorized Hoist dealer Be sure to have your serial number and this manual when calling When all parts have been accounted for continue TOOLS REQUIRED Socket Wrench2. 9 16 and 3 4 Sockets Crescent Wrench Rubber Mallet Tape Measure HS1225 Assembly 0757 Page 2 OWNERS MANUAL Page 3 OLST HS1225 Assembly OWNERS MANUAL 7 2 3 Page 4 HS1225 Assembly OWNERS MANUAL Step 2a FRAME ASSEMBLY In step 8 1 start assembly by bolting 22 s to 23 Wrench tighten bolts In step 2 bolt 3 and 6 to 23 Wrench tighten Lift machine to position CA s Part Descriptions Hardware Descriptions 3 Rear Upright Assembly A 1 2 13UNC x 3 HHB WZ 6 Main Base Assembly AA 1 2 SAE Flat Washer WZ 22 Weight frame Upright BA 1 2 Nylok Nut WZ 23 Cross Brace Assembly CA Rubber Foot Plate Mn Page 5 OLST HS1225 Assembly OWNERS MANUAL HS1225 Assembly HOIS 7 6 OWNERS MANUAL Step 2b FRAME ASSEMBLY Start by sliding both 28 5 through both and slide 28 s into 23 Tilt both 28 s forward enough to allow room to slide the weights on Next Slide all 27 s 25 26 and 21 onto both 28 s Tilt 28 s back to vertical position At the same time slide 21 up and attach 2 to 22 s as shown in detail A 1 Wrench tighten bolts Part Descriptions Hardware Descriptions 2 Top Weight Mount Assembly A 1 2 13UNC x 3 HHB WZ 3 Rear Upright Assembly 1 2 13UNC x 3 1 4 HHB WZ 21 Guide Rod Top Mount C 5 16 18 x 5 1 6 Socket Set Screw
3. 51225 Assembly FITNESS SYSTEMS OWNERS MANUAL WEIGHT RATIOS 12112 O 2 50 1212 6 3 76 50 1210 0 4 12112 O 5 124 1212 160 1212 7 474 212 O8 200 12 12 9 224 1212 O40 250 12112 O4 274 1212 2 300 12 1 2 3 324 5 42 1 2 44 850 1210 O45 374 12 1 2 016 400 NS 5 897 AALAIT LHOISA TVNLOV The above chart shows the standard weight stack for this unit The weights listed are approximate and have been rounded off to the nearest poind To find the actual weight you are lifting you would come down from the ratio being used and across from the number of the weight plate you have pinned Hoist reserves the right to modify the weight stack from the one shown without prior notice HS1225 Assembly OST Page 32 OWNERS MANUAL TP Page 33 7 HS1225 Assembly FITNESS SYSTEMS OWNERS MANUAL WEIGHT TRAINING TIPS Always consult your physician before starting any exercise program Hoist equipment is designed to maximize your time spent working out Having an exercise routine planned out in advance will allow you to get the most benefit out of the time spent exercising and will also
4. particular purpose There are no warranties which extend beyond the description on the face hereof ALTERATION NEGLECT ABUSE MISUSE NORMAL WEAR amp TEAR ACCIDENT DAMAGE DURING TRANSIT OR INSTALLATION FIRE FLOOD ACTS OF GOD Hoist is not responsible for the repair or replacement of any parts that Hoist determines have been subjected after the date of manufacture to alteration neglect abuse misuse normal wear amp tear accident damage during transit or installation fire flood oran ACT OF GOD TRANSPORTATION COSTS Hoist will accept parts covered under this warranty freight collect provided that shipment has received prior approval Hoist is not responsible for any other transportation costs but will ship freight collect parts either repaired or replaced under these warranties WARRANTY CLAIMS All claims should include model number the serial number proof of purchase date of installation and all pertinent information supporting the existence of the alleged defect Hoist Fitness Systems 9990 Empire St 130 San Diego Calif 92126 800 548 5438 Web Site www hoistfitness com PLEASE KEEP THIS FOR YOUR RECORDS Ho Page 45 zz OST HS1225 Assembly
5. 001 026 01M0134 030 030310 019 0001001 06 0192 06 0193 016 0001001 026 01PL125 026 01PL372 016 0201017 014 0009007 014 0005001 026 018C277T 26 STD 06 0329 026 01PL290 026 01M760 r Description 1 2 13UNC x 3 HHB WZ 1 2 13UNC x 3 1 4 HHB WZ 5 16 18UNC x 5 16 Socket Set Screw WZ 1 2 13UNC x 4 HHB WZ 1 2 13UNC x 2 FHB WZ 1 2 13UNC x 3 3 4 HHB WZ 1 2 13UNC x 2 1 2 HHB WZ 5 16 18UNC x 1 1 4 FHB BZ 3 8 16UNC x 2 1 2 HHB WZ 3 8 16UNC x 3 HHB WZ 3 8 16UNC x 3 1 2 HHB WZ 3 8 16UNC x 2 HHB WZ 5 16 18UNC x 1 1 4 HHB WZ 1 4 20UNC x 5 BHB WZ 1 2 13UNC x 4 3 4 HHB WZ 1 2 13UNC x 4 1 2 HHB WZ 1 2 SAE Flat Washer WZ 3 8 USS Flat Washer WZ 1 4 USS Flat Washer WZ 5 16 USS Flat Washer WZ 5 16 Internal Tooth Lock Washer WZ 1 2 Split Washer WZ 5 16 SAE Flat Washer BZ 1 2 Nylok Nut WZ 3 8 Nylok Nut WZ 1 4 Nylok Nut WZ 5 16 Nylok Nut BZ Rubber Foot Plate Weight Stack Bumper Large Plastic Foot Plate 11 16 Flanged Pulley Spacer 1 Flanged Pulley Spacer 4 1 2 Cable Pulley 3 1 2 Cable Pulley Left Placard Right Placard Intermediate Weight Bushing Guide Rod Bushing Lanyard Selector Pin Stand off Lanyard Coil Selector Pin 97 16 x 2 3 4 Roll Pin Plug Bumper 2 4 Flat End Cap 2 x 3 Elliptical End Cap 1 1 2 x 1 1 2 End Glide Sleeve 61 96 LD x 8 00 Ig Closed End Grip 92 00 End Cap 01 00 Flanged Ball Beari
6. 23 Hardware Descriptions CJ Intermediate Weight Bushing CK Guide Rod Bushing CL Lanyard Selector Pin Stand Off CM Lanyard Coil CN Selector Pin CO 07 16 x 2 3 4 Roll Pin CP Plug Bumper CQ 2 x 4 Flat End Cap CR 2 x 3 Elliptical End Cap CS 1 1 2 x 1 1 2 End Cap CT Glide Sleeve CU 01 96 LD x 8 00 Ig Closed End Grip CV 02 00 End Cap CW 01 00 Flanged Ball Bearing CX 00 75 Flanged Ball Bearing 51225 Assembly HS1225 Assembly OWNERS MANUAL 9 amp 9 lt CD THE BOTTOM OF THE SEAT PAD HOIST Page 25 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 2 1 1 1 2 1 1 1 1 1 2 1 2 2 1 OWNERS MANUAL PART LISTING Part Number 026 01X0185 026 01X0866 026 01X0865 026 01X1444 026 01X1445 026 01X1446 026 01X1447 026 01X1448 026 01X1449 026 01X1450 026 01X1451 026 01X1452 022 01PD0108 A 022 01PD0109 022 01PD0110 026 01M0779 026 01M0772 026 01M0773 026 01M0729 026 01T1451 026 01P0819 026 01X0864 026 01T0545 020 1100089 026 01W0111 026 1300034 026 01W0101 026 01G0159 026 01M0586 026 01M0519 026 01M0781 026 01X1601 HOIST FITNESS SYSTEMS Description 1 2 Short Pullpin Hex Head Assy Top Weight Mount Assembly Rear Upright Assembly Right Upright Assembly Left Upright Assembly Main Base Assembly Foot Mount Assembly Uprigh
7. BZ 23 Cross Brace Assembly Q 1 2 13UNC x 4 3 4 HHB WZ 25 16 Hole Weight Stem AA 1 2 SAE Flat Washer WZ 26 8 25 lbs Top Weight BA 1 2 Nylok Nut WZ 27 12 50 lbs Intermediate Weight Plate 28 00 75 x 60 69 Guide Rod Mn Page 7 OLST HS1225 Assembly OWNERS MANUAL SEE DETAIL A 1 FOR ASSEMBLY DETAIL A 1 NN Uf b Page 8 HS1225 Assembly OWNERS MANUAL Step 2c FRAME ASSEMBLY In step b 1 start by attaching 8 to 12 Wrench tighten bolts In step b 2 slide 18 s into both sides of 9 and attach 9 to 12 as shown Wrench tighten bolts then back nut off enough so 9 pivots freely Part Descriptions Hardware Descriptions 8 Upright Back Assembly D 1 2 13UNC x 4 HHB WZ 9 Seat Assembly E 1 2 13UNC x 2 FHB WZ 12 Movement Arm Assembly AA 1 2 SAE Flat Washer WZ 18 00 75 x 1 20 CRS BA 1 2 Nylok Nut WZ Page 9 AF 0 57 51225 Assembly OWNERS MANUAL STEP b 2 HS1225 Assembly HOIS J Page 10 OWNERS MANUAL Step 2d FRAME ASSEMBLY Start assembly by attaching 4 5 and 12 at the same time Wrench tighten bolis Next attach 16 in between 4 and 5 Wrench tighten bolt Make sure 12 bottom bumpers are aligned to 16 when 12 pivots to a stop Part Descriptions Hardware Descriptions 4 Right Upright Assembly B 1 2 13UNC x 3 1 4 HHB WZ 5 Left Upright Assembly AA 1 2 SAE Flat Washer WZ 6 Main Base As
8. Flat Washer WZ AG 5 16 SAE Flat Washer BZ BA 1 2 Nylok Nut WZ BD 5 16 Nylok Nut BZ CC Large Plastic Footplate Page 15 7 1225 Assembly OWNERS J MANUAL HS1225 Assembly Page 16 OWNERS MANUAL Step 2g CABLE ASSEMBLY Part Descriptions Hardware Descriptions 2 Top Weight Mount Assy 3 8 16UNC x 3 1 2 HHB WZ 6 Main Base Assembly J 3 8 16UNC x 2 1 2 HHB WZ 8 Upright Back Assembly K 3 8 16UNC x 3 HHB WZ 29 Cable Adaptor M 3 8 16UNC x 2 HHB WZ AB 3 8 USS Flat Washer WZ BB 3 8 Nylok Nut WZ CD 11 16 Flanged Pulley Spacer CF 4 1 2 Cable Pulley CG 3 1 2 Cable Pulley DB 1 2 Flanged Pulley Spacer WARNING CABLE BOLT MUST BE THREADED A MINIMUM OF 1 2 INTO ITS RECEIVER WITH JAM NUT TIGHTENED SECURELY TO ENSURE PROPER CONNECTION FINE TUNING LOOSEN JAM NUT AND THREAD BOLT IN OUT TO GIVE THE CABLE PROPER TENSION RE TIGHTEN 207 5257 80mm 1 2 13 NC SERRATED 1 2 15 NC SERRATED 3 16 SINGLE SHANK BALL FLANGED LOCK NUT FLANGED LOCK NUT NOTE MIL SPEC GF1887903 INSTALL CABLE AND PULLEYS AT THE SAME TIME Page 17 HOI 7 FITNESS SYSTEMS NOTE BE SURE CABLE RUNS BETWEEN THE PULLEY AND THE GUARD SHAFT 3 16 SINGLE SHANK BALL 51225 Assembly OWNERS MANUAL Page 18 ZI 39Vd OL 43134 51225 Assembly OWNERS MANUAL Step 2h FRAME ASSEMBLY S
9. I ES o ja 4 Ts E Ng gl J M 5198 A A S A 195 uonnodoy 5 DOT ONINIVAL posn 14919 M 5 5 Arus 1d 5 51225 Assembly HOIST Page 36 OWNERS MANUAL Agra Page 37 OS 7 51225 Assembly OWNERS MANUAL HS1225 Assembly Page 38 OWNERS MANUAL DECAL REFERENCE 021 0004061 021 0003093 www hoistfitness com 03 02 000000 021 0003203 LACEMENT PARTS SO WILL VOID WARR Page 39 OST HS1225 Assembly 51225 Assembly OWNERS MANUAL DECAL REFERENCE 021 0004029 PINCH POINTS 021 8 021 0003114 Page 40 OWNERS MANUAL DECAL REFERENCE 12345 6 7 8 910 021 0004109 021 0003011 HE Page 41 OLST HS1225 Assembly OWNERS MANUAL MAINTENANCE SCHEDULE m Inspect Links Pull Pins Snap Locks DAILY WEEKLY Swivels Weight Stack Pins Clean Inspect Cables or Belts and their DAILY WEEKLY tension Inspect Inspect WEEKLY 3 MONTHS All Decals inspect All Nuts and Bolts Tighten if needed WEEKLY 3 MONTHS Inspect Clean amp Lubricate Guide Rods w
10. each decal Nuts and Bolts Inspect all nuts and bolts for any loosening and tighten if needed Go through a re tightening sequence periodically to ensure that all hardware is tensioned proper Anti Skid Surfaces These surfaces are designed to supply secure footing and need to be replaced if they appear worn or become slippery Belts and Cables Hoist uses only high quality belt and mil spec cables Visually inspect the belts and cables for fraying cracking peeling or discoloration While the machine is not in use carefully run your fingers along the belt or cable to feel for thinning or bulging areas Replace belts and cables immediately at the first signs of damage or wear Do not use equipment until belts or cables has been replaced nt Page 43 M 7 51225 Assembly FITNESS SYSTEMS OWNERS MANUAL GENERAL MAINTENANCE INFORMATION CONTINUED Belt and Cable Tension Referring to the Owners Manual when belts or cables are used check all bolts attachments to be sure they are properly atiached Check slack in cables and re adjust cable tension if needed Seat Sleeves Turcite Bushings Wipe down adjusting tubes with a dust free rag before applying lubricant Lubricate seat sleeves and turcite bushings with a Silicon or Teflon based lubricant spray Linear Bearings Referring to the Owners Manual carefully dis assemble the bearing from its housing and place a finger full of light grease lithiu
11. enable you to work all the major muscle groups Warm up properly before engaging in weight resistance training Stretching yoga jogging calisthenics or other cardiovascular exercise can help prepare your body for the heavier workload of lifting weights Learn how to perform the exercise correctly before using heavy weight Correct form is important to avoid injury and to ensure that you work the proper muscle groups Know your limitations If you are new to weight training or are embarking on an exercise regimen after a long layoff start slowly and build foundational strength over a longer period of time Pay attention to your breathing Exhale when you exert is a general rule of thumb Never hold your breath Page 34 OST HS1225 Assembly OWNERS MANUAL Page 35 OIS 7 HS1225 Assembly OWNERS MANUAL A 1 EE 1 1 qp HA w NS TE un LLL A DD LLL LLLLLLLLLLLLLLLISs PEE Ee L tt tt TE TE EE TE TE 1111111 TT un eee 2 98 1 1 ERE ST EJ 27
12. ic components belts cables or upholstery that occur after three years all malfunctions of pulleys bearings or bushings that occur after five years The frame and all welded components are warranted for the life of the product Hoist Fitness Systems sole responsibility shall be to repair or replace the component within the terms stated above Hoist Fitness Systems shall not be liable for any loss or damage of any kind including any incidental or consequential damages resulting directly or indirectly from any warranty expressed or implied or any other failure of this product WHAT IS NOT COVERED BY THIS WARRANTY Hoist s sole obligation under this warranty is limited to either repair or replacement of parts subject to the additions below This warranty neither assumes nor authorizes any person to assume obligations other than expressly covered by this warranty NO CONSEQUENTIAL DAMAGES Hoist is not responsible for economic loss profit loss or special indirect or consequential damages WARRANTY IS NOT TRANSFERABLE This warranty is not assignable and applies only in favor of the original purchaser user to whom delivered Any such assignment or transfer shall void the warranties herein made and shall void all warranties expressed implied or statutory except the one 1 and five 5 year warranties described above These warranties are exclusive and in lieu of all other warranties including implied warranty and merchantability or fitness for a
13. ith a Teflon PTFE MONTHLY 3 MONTHS based lubricant Superlube Lubricate Seat Sleeves Turcite Bushings MONTHLY 3 MONTHS Linear Bearing Clean and Wax Repack with Grease Replace Cables Belts and Connecting Parts YEARLY 3 YEARS Your equipment comes with a commercial maintenance decal For personal in home use please follow the home maintenance schedule listed above FITNESS SYSTEMS HS1225 Assembly HOLIS 7 42 OWNERS MANUAL HOIST FITNESS SYSTEMS GENERAL MAINTENANCE INFORMATION Links Pull Pins Snap Locks Swivels Weight Stack Pins Check all pieces for signs of visible wear or damage Check springs in snap hooks and pull pins for proper tension and alignment If the spring sticks or has lost its rigidity replace it immediately Upholstery To ensure prolonged upholstery life and proper hygiene all upholstered pads should be wiped down with a damp cloth after every workout Periodically take the time to use a mild soap or an approved vinyl upholstery cleaner to deter the onset of cracking or drying Avoid using any abrasive cleaners or cleaners not intended for use on vinyl Replace ripped or warn upholstery immediately Keep sharp or pointed objects clear of all upholstery Guide Rods Wipe clean with a dust free rag Lubricate once a week with a Silicon or Teflon based lubricant Decals Inspect and familiarize yourself with any safety warnings or other user information posted on
14. m super lube etc into the inside of the bearing Using your finger press the grease into the ball bearings and their tracks repeat until the ball bearing tracks are full of grease Insert the shaft back into the bearing and wipe off excess grease PLEASE KEEP THIS FOR YOUR RECORDS FITNESS SYSTEMS TP HS1225 Assembly I OZ 7 44 OWNERS MANUAL HOIST FITNESS SYSTEMS LIMITED LIFETIME WARRANTY Hoist Fitness Systems warrants this product to the original purchaser to be free from defects in workmanship and or materials under normal use or service If at any time a component part is defective Hoist Fitness Systems shall repair or replace it at Hoist Fitness Systems option within a reasonable period of time This warranty does not cover costs of removal transportation or reinstallation This warranty shall not apply if the defect was caused by misuse neglect or normal wear and tear Starting from the original date of purchase normal wear and tear shall be considered as the following COMMERCIAL USE All malfunctions of upholstery grips paint and chrome that occur after 180 days all malfunctions of electronic components belts or cables after one year all malfunctions of pulleys bearings or bushings that occur after five years The frame and all welded components are warranted for the life of the product HOME USE All malfunctions of grips paint and chrome that occur after one year all malfunctions of electron
15. ng 90 75 Flanged Ball Bearing 207 Cable Plug Spacer 1 2 Flanged Pulley Spacer Page 26 OWNERS MANUAL ABBREVIATION LISTING BZ Black Zinc WZ White Zinc FHS Flat Head Screw BHS Button Head Screw SHS Socket Head Screw Hex Head Bolt Mn Page 27 H 7 1225 Assembly OWNERS MANUAL 5 16 BOLT 1 3 4 2 3 4 3 3 4 2 1 4 3 1 4 4 1 1 4 4 1 4 5 1 4 1 3 4 2 3 4 3 3 4 3 1 4 1 2 SHOULDER BOLT 1 1 4 2 1 4 1 1 2 x 2 1 2 3 1 2 p 2 4 HS1225 Assembly MOIST Page 28 OWNERS MANUAL 3 8 FLATHEAD SOCKET SCREW 374 VA rnm Om 1 4 BOT gyp SCREW Om Page 29 OIS 7 51225 Assembly OWNERS MANUAL 5 16 3 8 1 2 1 2 FLAT WASHER FLAT FLAT WASHER FLAT WASHER LARGE 055 25mm WASHER SMALL SAE 26mm LARGE USS 34mm 1 4 3 8 1 2 LOCK WASHER LOCK WASHER LOCK SHIM WASHER 3 8 FENDER WASHER 16 PLASTIC 1 1 16 FENDER FENDER WASHER HS1225 Assembly Page 30 OWNERS MANUAL 1 4 LONG 1 2 LONG FLANGED SPACER FLANGED SPACER 1 4 LONG 11 16 LONG 1 LONG FLANGED SPACER FLANGED SPACER FLANGED SPACER 1 2 LONG 1 LONG SPACER SPACER 1 3 8 ALUMINUM 1 5 8 ALUMINUM FLATHEAD CAP FLATHEAD CAP TP Page 31 Ol 7
16. sembly BA 1 2 Nylok Nut WZ 12 Movement Arm Assembly 16 01 25 x 2 00 CRS 30 Aluminum Bolt on Cap Page 11 OIS 7 HS1225 Assembly OWNERS MANUAL HS1225 Assembly HOIS 7 Page 12 OWNERS MANUAL Step 2e FRAME ASSEMBLY Start assembly by sliding 17 s into both ends of 10 Next attach 10 to 6 and 9 Wrench tighten bolts then back nut off so 8 and 10 pivots freely Next slide 19 into 9 and attach 11 to 8 Wrench tighten bolts then back nut off so 11 pivots freely Part Descriptions Hardware Descriptions 6 Main Base Assembly 1 2 13UNC x 3 3 4 HHB WZ 8 Upright Back Assembly G 1 2 13UNC x 2 1 2 HHB WZ 9 Seat Assembly AA 1 2 SAE Flat Washer WZ 11 Back Upholstery Mount Assy 1 2 Nylok Nut WZ 17 00 75 x 1 75 CRS AF 1 2 Split Washer WZ 30 Aluminum Bolt on Cap Page 13 0757 51225 Assembly OWNERS MANUAL 51225 Assembly Page 14 OWNERS MANUAL Step 2f FRAME ASSEMBLY Start assembly by attaching both to 7 Wrench tighen bolts Next slide 7 onto 20 and attach 20 to 6 as shown Wrench tighten bolts Part Descriptions Hardware Descriptions 6 Main Base Assembly 1 2 13UNC x 3 1 4 HHB WZ 7 Foot Mount Assembly G 1 2 13UNC x 2 1 2 HHB WZ 20 Chrome Adjuster 5 16 18UNC x 1 1 4 BZ 31 0 25 x 9 56 LD Aluminum Spacer AA 1 2 SAE
17. t Back Assembly Seat Assembly Linkage Assembly Back Upholstery Mount Assy Movement Arm Assembly Back Pad Assembly Seat Pad Assembly Low Back Seat Pad Assy 91 25 x 2 00 CRS 00 75 x 1 75 CRS 00 75 x 1 20 CRS 01 00 x 2 78 Ig Chrome Adjuster Guide Rod Top Mount Weight Frame Upright Cross Brace ssembly SSH189 Shield 16 Hole Weight Stem 8 25 lbs Top Weight 12 50 Ibs Intermediate Weight Plate 00 75 x 60 69 Guide Rod Cable Adaptor Aluminum Bolt on Cap 25 x 0 56 LD Aluminum Spacer Seat Belt Assembly 51225 Assembly Key A ER sita Aa z gt 51225 Assembly OWNERS MANUAL HARDWARE LISTING NOTE SOME OF THESE PARTS MAY COME PRE INSTALLED Quy 1 6 2 2 2 1 3 4 1 1 2 2 8 7 2 4 4 4 6 8 8 1 4 2 6 6 4 DO gt N N N IN N amp N N S FITNESS SYSTEMS Part Number 011 0407016 011 0407036 011 0311012 011 0101070 011 0102025 011 0407019 011 0407018 011 0303010 011 0107009 011 0407026 011 0107051 011 0107052 011 0407029 011 0101074 011 0107042 011 0207030 013 0102003 013 0402005 013 0006006 013 0102004 013 0102021 013 0102018 013 0202003 012 0304011 012 0104008 012 0104009 012 0004005 026 01PL195 019 0001005 026 01PL344 026 01M0532 026 01M0551 018 0001003 018 0001002 021 0013140 021 0013141 026 01W0122 026 01PL134 026 01PL291 010 0008
18. tart assembly by attaching 14 and 15 to 9 Wrench tighten bolts Next attach 11 to 13 and wrench tighten bolts Part Descriptions Hardware Descriptions 9 Seat Assembly N 5 16 18UNC x 1 1 4 HHB WZ 11 Back Upholstery Mount Assy AD 5 16 USS Flat Washer WZ 13 Back Pad Assembly AE 5 16 Lock Washer WZ 14 Seat Pad Assembly He Page 19 OIS r HS1225 Assembly OWNERS MANUAL Page 20 HS1225 Assembly OWNERS MANUAL Step 2i FRAME ASSEMBLY Attach 24 CH and to 22 s as shown Wrench tighten bolts Part Descriptions Hardware Descriptions 22 Weight Frame Upright P 1 4 20UNC x 5 BHB WZ 24 SSH189 Shield R 1 2 13UNC x 4 1 2 WZ AA 1 2 SAE Flat Washer WZ AC 1 4 USS Flat Washer WZ BA 1 2 Nylok Nut WZ BC 1 4 Nylok Nut WZ CH Left Placard CI Right Placard DA Spacer Page 21 HS1225 Assembly OWNERS MANUAL Page 22 A NNNNW HS1225 Assembly OWNERS MANUAL PRE ASSEMBLY Part Descriptions 1 1 2 Short Pullpin Hex Head Assy 4 Right Upright Assembly 5 Left Upright Assembly 6 Main Assembly 7 Foot Mount Assembly 8 Upright Back Assembly 9 Seat Assembly 10 Linkage Assembly 12 Movement Arm Assembly 14 Seat Pad Assembly 20 Chrome Adjuster 22 Weight Frame Upright 25 16 Hole Weight Stem 26 8 25lbs Top Weight 32 Seat Belt Page
Download Pdf Manuals
Related Search