Hobart N50 User's Manual
Contents
1. Fig 1 on the front of the bowl support fit in the holes on the sides of the bowl Lock the bowl in place by rotating the bowl clamps Fig 1 over the ears of the bowl AGITATOR To install an agitator the bow must be installed and fully lowered Place the agitator in the bowl push it up on the agitator shaft Fig 1 and turn it clockwise to seat the shaft pin in the slot of the agitator shank MIXING This section explains operation of the mixer A Compact Disk with the Use and Applications Handbook is provided with the mixer which contains information on mixing procedures and outlines specific uses for agitators CIRCUIT BREAKER The 115 60 1 units are equipped with a circuit breaker to prevent overloading the mixer The circuit breaker will trip if mixer is overloaded Ensure mixer is shut off and unplug unit prior to removing the overloading condition and resetting the circuit breaker Follow Troubleshooting guide if unit will not start CLEANING WARNING UNPLUG MACHINE POWER CORD BEFORE BEGINNING ANY CLEANING PROCEDURE DAILY Bowls and agitators should be removed from the mixer and cleaned in a sink DO NOT use a hose to clean the mixer it should be wiped with a clean damp cloth Remove the agitator spring for cleaning 1 Slip the lower end of the spring underneath the agitator pin and screw in a counterclockwise motion until the spring comes off Fig 2 2 After cleaning reinstall the agitator sp2. IONS GENERAL The model N50 mixer is a 5 quart countertop mixer equipped with a 1 6 H P motor cord and plug as standard equipment INSTALLATION UNPACKING Immediately after unpacking the mixer check for possible shipping damage If this machine is found to be damaged after unpacking save the packaging material and contact the carrier within 15 days of delivery LOCATION Before installation test the electrical service to make sure that it agrees with the specifications on the machine data plate Place the mixer on a suitable sturdy level surface There should be adequate space around the mixer for the user to operate the controls and install and remove bowls ELECTRICAL CONNECTIONS WARNING THE ELECTRICAL CORD ON THIS MACHINE IS EQUIPPED WITH A THREE PRONGED GROUNDING PLUG WHICH MUST BE CONNECTED TO A PROPEREY G ROUNDEDSRECEP TAGE SIEAREESRECER nA CET San Oig ERE PROPER GROUNDING TYPE CONTACT AN ELECTRICIAN DO NOT REMOVE THE GROUNDING PRONG FROM THE PLUG 3 OPERATION WARNING MOVING AGITATOR IN BOWL KEEP HANDS CLOTHING AND UTENSILS OUT WHILE IN OPERATION Fig 1 Gear Shift Lever ul r Drip Cup d Bowl Clamp Alignment Pin Bowl Support Circuit Breaker CONTROLS The ON OFF switch Fig 1 is used to start and stop the mixer The gear shift lever Fig 1 is used to change speeds Always stop the mixer before changing speeds To change speeds turn the switch OFF move the gear shift leve
3. N50 MIXER INSTRUCTIONAL MANUAL Model N50 ML 134262 ML 134268 701 S RIDGE AVENUE TROY OHIO 45374 0001 937 332 3000 e WWW HOBARTCORP COM IMPORTANT SAFEGUARDS When using electrical appliances basic safety precautions should always be followed including the following ie 2 Read all instructions To protect against the risk of electrical shock do not put mixer in water or other liquid Close supervision is necessary when this or any appliance is used by or near children Unplug mixer from outlet when not in use before putting on or taking off agitator and before cleaning Avoid contact with moving parts Keep hands hair and clothing as well as spatulas and other utensils away from the agitator during operation to reduce the risk of injury to persons and or damage to the mixer Do not operate the mixer with a damaged cord or plug after the mixer malfunctions or is dropped or damaged in any manner Return appliance to the nearest authorized service center for examination repair electrical or mechanical adjustment Hobart does not recommend the use of hub attachments with this machine Do not use the mixer outdoors Do not let the cord hang over edge of table or counter Remove agitator flat beater wire whip or dough hook from the mixer before washing SAVE THESE INSTRUCTIONS FOR SERVICE AND PARTS CALL 1 888 4HOBART INSTALLATION OPERATION AND CARE OF N50 MIXER SAVE THESE INSTRUCT
4. r to the desired speed and turn the switch back ON NOTE There is a mechanism which prevents the gear shift lever from being moved with the switch in the ON position and also prevents the switch from being turned ON if the gear shift lever is between gears 4 No30 MIXER OPERATION CONTINUED SPEED 1 Low This speed is for heavy mixtures such as bread dough heavy batters and potatoes Speed 2 Medium This speed is for light dough which must rise quickly cake batters and some whipping operations SPEED 3 High This is a fast speed for light work such as whipping cream beating eggs and mixing thin batters The bowl lift handle is used to raise and lower the bowl To raise the bowl rotate the handle upward rotating the handle downward lowers the bowl Circuit breaker provided only on 115 60 1 units Not provided on ASTM units BOWL New mixer bowls and agitators beaters whips and dough hooks should be thoroughly washed with hot water and a mild soap solution rinsed with either a mild soda or vinegar solution and thoroughly rinsed with clear water BEFORE being put into service This cleaning procedure should also be followed for bowls and agitators before whipping egg whites or whole eggs The bowl must be installed before the agitator To install the bowl fully lower the bowl support Fig 1 Position the bowl so the alignment bracket on the back of the bowl is in the bowl retainer and the alignment pins
5. ring by reversing this procedure Fig 2 NOTE All coils of the spring should be above the agitator pin CAUTION Do not operate agitators without the agitator spring in place Damage to mixer will result PERIODIC The drip cup Fig 1 should be removed and wiped clean MAINTENANCE WARNING UNPLUG MACHINE POWER CORD BEFORE BEGINNING ANY MAINTENANCE PROCEDURE BOWL LIFT SLIDEWAYS The slideways Fig 1 should be lubricated twice a year Apply a light coat of Lubriplate 630AA to all three surfaces of both slideways SERVICE If service is required on this equipment return it to your local Hobart Service Center For an authorized Hobart Service Center call 1 888 4HOBART TROUBLESHOOTING PROBLEM POSSIBLE CAUSE Mixer will not start 1 Check incoming power source and make sure unit is plugged in 2 Check circuit breaker on mixer Verify that circuit breaker is reset by pressing in on the black button Fig 1 3 Take mixer to your local Hobart Service Center 8 F34853 Rev B 08 05
Download Pdf Manuals
Related Search