Hobart ML-136134 User's Manual
Contents
1. INCLUDES REPLACEMENT PARTS HOBART HOBHL2 Heat Lamp ML 136134 701 S RIDGE AVENUE TROY OHIO 45374 0001 937 332 3000 www hobartcorp com F 35216 Dec 2006 Installation Operation and Care of the Hobart HOBHL2 Heat Lamp SAVE THESE INSTRUCTIONS GENERAL The HOBHL2 Heat Lamp is used in conjunction with a 2912B Slicer to maintain cooked roast beefto an internal temperature above 140 F for up to 30 minutes while slicing The Heat Lamp is designed to hold this temperature with roasts placed on the slicer carriage tray at a minimum temperature of 150 F for up to 30 minutes Additional heating lamps placed on the slicer platter and the weighing scale will prevent additional temperature loss beyond the 20 F drop from sliced product temperature INSTALLATION UNPACKING Immediately after unpacking the Heat Lamp check for possible shipping damage If the Heat Lamp is found to be damaged after unpacking save the packaging material and contact the carrier within 15 days of delivery to file a claim ASSEMBLY The tools needed for this installation are an electric drill a center punch and a s2 drill bit CAUTION reduce the risk of fire the Heat Lamp is to be installed non combustible surroundings only with minimum clearances to combustible walls ceilings countertops and other combustible materials as noted in the diagram below 17 A AE lu 7 KA COMBUSTIBLE OVERHEAD CLEARANCE CEILING COMBU2. STIBLE WALLS 18 MIN CLEARANCE ALL SIDES A MS COUNTERTOPS WITHIN FRONT VIEW 12 MIN 12 IN ALL SIDES MUST TOP VIEW BE METAL OR OTHER 12 MIN 18 MIN gt NON COMBUSTIBLE MATERIAL AA ne i HOBART 2006 2 Place skid plate on table where slicer is to be located Make sure there is sufficient room on the table to support the front feet of the slicer the feet on the index knob end of slicer before drilling holes for the skid plate Check beneath the tabletop to be surethere are nohazards before drilling holes for mounting the heat lamp Make sure there is sufficient room for the reinforcement base plate Mark and center punch the five 3 2 holes to be drilled Fig 1 Drill the five 32 holes Line up four holes in mounting base plate with holes in skid plate table and reinforcementbase plate Attach with hardware provided NOTE Reinforcementbase plate lockwashers and nuts are to be installed underneath tabletop not on top 7 10 Install screw to secure right side of skid plate Fig 1 Insert heat lamp assembly onto Mounting Base Plate Fig 2 Secure with thumbscrew Install four short feet on slicer and put slicer in position with rear feet sitting in holes in skid plate Check to be sure the two 250 watt infrared bulbs are tight in the socket Remove one Cushion Spring and hand tighten the bulb to be sure it is secure Reinstall the Cushion Spring as sh
3. T NO 00 914161 00 914137 00 914136 00 914159 WL 006 06 SC 125 54 00 914134 00 438131 00003 00 914174 WL 006 06 SC 125 54 NS 011 23 00 914180 00 914190 00001 00 914167 00 914212 00 914166 00 914170 00002 00 914200 00 914542 00 914205 00002 SC 021 14 WL 006 01 SC 127 28 WL 006 06 00 914173 00 914187 00 914200 00 914170 00001 00 914166 00 914167 00 914212 00 117542 00021 FE 017 41 00 914204 00003 00 438131 00183 00 438131 00184 00 914182 00 914190 00002 00 914154 SC 129 61 00 914140 SC 127 28 WL 006 06 NS 011 12 WL 006 01 SC 021 16 00 914169 00 873255 00 914194 00 914160 00 914183 00 914540 FE 026 54 HOBART HEAT LAMP NAME OF PART AMT Emitter Full Trough FTE With Spring anna 1 Deflector Emitter will Cover Front Housing t Rivet 10 Lockwasher 10 Mach Screw 10 32 x 2 Phil Rd Hd SST Housing Heat Lamp Label Warning Cover Front Top Lockwasher 10 Mach Screw 10 32 x 2 Phil Rd Hd SST Nut 10 32 Hex SST Caplug Square 1 In Arm Flex Short Run Shade Infrared Lamp Label Max 120 V 250 Watts Spring Cushion nn Socket Assy 250 Watt Lamp Long Run Lam
4. ast on the slicer Controls The Heat Lamp is equipped with arocker switch Fig 5 on the main support post This switch turns the heating sources on or off 12159 CLEANING WARNING UNPLUG POWER CORD AND ALLOW HEAT LAMP TO COOL CAUTION Do not raise slicer until cool to prevent damage to plastic components on the slicer Remove the optional portable platter and move the front heat lamp gooseneck away from the slicer before raising the slicer up on the lift lever Wash all surfaces with a damp cloth or sponge and a mild detergent Exercise care when cleaning around the louvers in the main heat source housing or the cooling holes in the gooseneck lampshades so water does not enter those areas Do NOT wash inside lampshades or the bulbs and sockets Do NOT immerse unit in water Rinse with a cloth or sponge and clean water Sanitize Excessive amounts of sanitizer and use of products not formulated for stainless steel or aluminum may void your Hobart warranty Chlorinated sanitizer not to exceed 200 ppm MAINTENANCE SERVICE Contact your local Hobart authorized service office for any repairs adjustments or replacement parts The Infrared Lamps are considered expendable items and are not covered by the Hobart warranty HOBART HEAT LAMP ILLUS PL 58198 BHRBRHRHRHRRHRRPWWWWWWWWWWNNNNNNNNND S ifa WNHATCOOANDAAKRWNHADOOANDAAKRWNHACDOANDAARWNH O PAR
5. n nnr nr nn tna NaaaaaanDaapeaoANaa aaa aaa avanlaavyaARo aa ayanaaaaApAaayu NOTES FORM 35216 Dec 2006 8 PRINTED IN U S A
6. own in Fig 3 WARNING ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE APPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND OR OTHER LOCAL ELECTRICAL CODES 11 Plug power cord into nearest outlet 1 OF 3 CUSHION SPRINGS MOUNTING HOLES TO BE DRILLED REAR SLICER FEET GO HERE Fig 1 STUD ON gt MOUNTING _ BASE PLATE Fig 2 Fig 3 OPERATION WARNING THE HEAT LAMP AND ITS PARTS ARE HOT AND CAN CAUSE BURNS USE CARE WHEN OPERATING CLEANING AND SERVICING Set Up 1 2 Place Optional Portable Platter on the slicer Fig 4 The Main Heat Source is fixed in position over the slicer Carriage Tray Fig 4 No adjustment is necessary Adjust the Front Heat Lamp Gooseneck Fig 4 at approximately a 45 degree angle to shine on the optional portable platter Allow enough clearance to be able to reach into this area and remove the sliced beef without contacting the Heat Lamp housing Adjust the Rear Heat Lamp Gooseneck Fig 4 at approximately a 45 degree angle to shine on the Weighing Scale Platter again allowing enough room to work without contacting the Heat Lamp housing HEAT SOURCE REAR HEAT LAMP _ GOOSENECK FRONT HEAT B LAMP GOOSENECK CARRIAGE TRAY WEIGHING SCALE M PLATTER OPTIONAL PORTABLE PLATTER PL 57384 Fig 4 Preheating The Heat Lamp should be turned on and allowed to preheat for 30 minutes prior to placing a ro
7. p Infrared 120 V 250 Watts Switch Cover Switch Box ASS Mach Screw 8 32 x s Slotted Rd Hd SST Lockwasher 8 Helical Mach Screw 10 32 x 3 s Hex Hd Lockwasher 10 Helical Base Mounting Assy Screw Thumb eee eee Lamp Infrared 120 V 250 Watts Socket Assy 250 Watt Lamp Short Run Spring Cushion nn Shade Infrared Lamp Label 120 V 250 Watts Cord amp Plug accionada Relief Strain Box Switch Assy Label ON Label OFF Support Frame Assy Arm Flex Long Run Cover Support Frame Mach Screw 10 32 x a Phil Truss Hd SST Grate Heat Lamp Housing Mach Screw 10 32 x s Hex Hd SST Lockwasher 10 Helical Nut 8 32 Hex SST Lockwasher 8 Mach Screw 8 32 x 7 s Slotted Rd Hd SST Block Terminal Emitter Kit Tall Foot amp Skid Plate Reinforcement Base Plate Plate Skid Platter Portable ne Housing Heat Lamp Assy Incls Items 1 3 thru 7 amp 42 i Connector Wire Nut High n
Download Pdf Manuals
Related Search