Home

Henny Penny EEE-143 User's Manual

Contents

1. Figure 4 110 10 11 Model EEE 141 142 143 144 Once oil has drained from vat use the lift tool and lift the hinged element from the vat to clean the bottom of the vat Figure 2 Auto lift fryers hinge back the basket hooks over the top of the fryer before lifting the elements BURN RISK Use protective cloth or gloves when lifting the element with the lift tool The element may be hot and severe burns could result Avoid putting the lift tool in the center of the elements at the same area as the high limit bulb or damage to the high limit could result Scrape or brush the sides and the bottom of the vat Be careful not to damage the sensing probes Do not use steel wool other abrasive cleaners or cleaners sanitizers containing chlorine bromine iodine or ammonia chemicals as these will deteriorate the stainless steel material and shorten the life of the unit Do not use a water jet pressure sprayer to clean the unit or component damage could result Once the vatis clean and the display shows SCRUB VAT COMPLETE YES NO Press V button for YES and the display shows WASH VAT YES NO Lower the element and then press V button and display shows WASHING The oil circulates through the vat for several minutes Once the wash cycle is complete display shows WASH AGAIN YES NO Press V button for YES if another wash is needed otherwise press X button for
2. Press gt button and SP 8C and LOCKOUT ENABLED shows in the left display Press the and W buttons to choose YES or NO If set to YES press gt button and the left display shows SP 8D and LEFT VAT LOCKOUT CYCLES and the number of cook cycles before filter lock out shows on the right display 0 to 99 Use gm and WM or product buttons to change this number Press gt button and the left display shows SP 8E and RGHT VAT LOCKOUT CYCLES and the number of cook cycles before filter lock out shows on the right display 0 to 99 Use and W or product numbers to change this number Once this number of cook cycles is reached FILTER LOCKOUT YOU MUST FILTER NOW shows in the display and it refuses further cook cycles until the vat is filtered Full Vat If unit is a full vat SP 8A and FULL VAT FILTER CYCLES shows in the left display and the number of cook cycles between filters shows on the right display 0 to 99 Use A and Y or product numbers to change this number Press gt button and SP 8B and LOCKOUT ENABLED shows in the left display Press the 4X and W buttons to choose YES or NO If set to YES press gt button and the left display shows SP 8C and FULL VAT LOCKOUT CYCLES and the number of cook cycles before filter lock out shows on the right display 0 to 99 Use and or product buttons to change this number Once this number of coo
3. Refer to Figures 3 1 3 2 amp 3 3 in conjunction with the description of the functions below Function This LED lights when the control calls for heat for the left vat s and the elements come on and heat the oil During normal operation press this button to start and stop cook cycles for the left basket press to change displayed product also used for V to indicate YES or to confirm During normal operation press this button to start and stop cook cycles for the left basket press to change displayed product also used for X to indicate NO or cancel Shows the product codes shows the timer countdown during cook cycles shows the prompts during the filter modes shows the selections in the Program Mode shows the temperature of the oil by pressing AESi shows error codes also displays in several languages Press once to view oil temperature press twice to vew the setpoint temperature Used in the Programming Modes also used for lt q button press to display the following fryer information Status a actual oil temperature b oil setpoint temperature c recovery information for each vat Used in the Programming and Filtering Modes left button used for left split vatand right button used for W or amp buttons press to view the following filtering stats a number of cook cycles before next filter Global Filter Mode or percentage of filter allowance Mixed Mode b time and date of the most recent filter on each vat
4. H Y PENNY Global Foodservice Solutions Henny Penny Evolution Elite Reduced Oil Capacity Open Fryers Split Vat amp Full Vat Electric Model EEE 141 Model EEE 142 Model EEE 143 Model EEE 144 OPERATOR S MANUAL REGISTER WARRANTY ONLINE AT WWW HENNYPENNY COM LIMITED WARRANTY FOR HENNY PENNY EQUIPMENT Subject to the following conditions Henny Penny Corporation makes the following limited warranties to the original purchaser only for Henny Penny appliances and replacement parts NEW EQUIPMENT Any part of a new appliance except baskets lamps and fuses which proves to be defective in material or workmanship within two 2 years from date of original installation will be repaired or replaced without charge F O B factory Eaton Ohio or F O B authorized distributor Baskets will be repaired or replaced for ninety 90 days from date of original installation Lamps and fuses are not covered under this Limited Warranty To validate this warranty the registration card for the appliance must be mailed to Henny Penny within ten 10 days after installation FILTER SYSTEM Failure of any parts within a fryer filter system caused by the use of the non OEM filters or other unapproved filters is not covered under this Limited Warranty REPLACEMENT PARTS Any appliance replacement part except lamps and fuses which proves to be defective in material or workmanship within ninety 90 days from date of original instal
5. revert back to the cook mode and repeat the above steps To exit from the Special Program Mode at any time press and hold button for 2 seconds Degrees Fahrenheit or Celsius SP 1 The left display flashes SP 1 and TEMP FORMAT Press the A orW buttons to choose F or C e Use lt q button to go back to previous menu items e Press p gt button when finished with the current Level 2 step Language SP 2 Press j gt button and SP 2 and LANGUAGE flash on the left display Press the 44 or W buttons to select the desired language System Initialization SP 3 Press gt button and SP 3 and DO SYSTEM INIT flash in the display along with INIT on the right display To reset the controls to factory default settings press and hold V button and control counts down IN 3 IN2 IN 1 Once display shows INIT amp DONE the controls are reset to factory defaults Audio Volume SP 4 Press j button and SP 4 and VOLUME flash in the left display Press the A or W or use product buttons to adjust the volume of the speaker 10 being the maximum value and the minimum 6 2 le Y PENNY wedernice Solitons Coba Produ H 6 1 SPECIAL PROGRAM MODE Continued 6 3 Model EEE 141 142 143 144 Audio Tone SP 5 Press gt button and SP 5 and TONE flash in the left display Press the A or W oruse prod
6. shows in both displays Press on either side and SETUP ENTER CODE shows in the displays Press 1 2 3 and LANGUAGE shows on the left display ENGLISH on the right display Use Mor W buttons to change the operation display to FRANCAIS ESPANOL PORTUG DEUTSCHE SVENSKT RUSSIAN Press gt to continue with the other set up items which include TEMP FORMAT F or C TIME FORMAT 12 HR OR 24 HR ENTER TIME Time of day use product buttons to change ENTER TIME AM OR PM DATE FORMAT US MM DD YY or INTERNATIONAL DD MM YY ENTER DATE Today s date use product buttons to change DAYLIGHT SAVING TIME 1 OFF 2 US 2007 amp after 3 EURO 4 FSA US before 2007 FRYER TYPE ELEC or GAS VAT TYPE FULL OR SPLIT AUTOLIFT ENABLED NO LIFT or YES LIFT BULK OIL SUPPLY YES or NO BULK OIL DISPOSE YES or NO S N Shows serial number of the unit or can be recorded THIS SERIAL NUMBER SHOULD MATCH THE SERIAL NUMBER ON THE DATA PLATE ON THE DOORS 2nd LANGUAGE By setting a second language in the controls 2 languages can now be easily chosen by pressing during normal operation One language shows in the left display and the second language shows in the right display Pressing the V button under the desired language selects that language seen in displays 2nd VOLUME By setting a second volume in the controls 2 volumes can now be easily chosen by pre
7. Once vat is empty press V button and display shows SCRUB VAT COMPLETE YES NO Use brush to clean element and scour pad to clean vat if needed Do not scrape the electric fryer elements or use scouring pads on the elements This produces scratches on the surface of the element causing breading to stick and burn Do not use steel wool other abrasive cleaners or cleaners sanitizers containing chlorine bromine iodine or ammonia chemicals as these will deteriorate the stainless steel material and shorten the life of the unit Do not use a water jet pressure sprayer to clean unit or AE A J msm Use the lift tool and lift the elements from the vat as needed Auto lift fryers hinge back the basket hooks over the top of the fryer before lifting the elements 13 Once vat is clean press the V button and display shows RINSE VAT If drain is not open display shows OPEN DRAIN Open the drain 14 Pour clean water and approximately 8 ozs 0 24 liters of distilled vinegar solution into vat to rinse vat and allow rinse water to drain into drain pan Rinse at least 3 times but be careful not tooverfill the drain pan Display now shows RINSE COMPLETE YES NO 15 Once vat is completely rinsed press the V button and display shows CLEAR SOLUTION FROM OIL LINES PUMP X DONE To make sure no cleaning solution remains in the oil lines press and hold
8. 143 144 BURN RISK The filter drain pan must be as far back under fryer as it will go and the cover in place Be sure the filter drain pan is latched into place and the hole in the cover lines up with the drain before opening the drain Failure to follow these instructions causes splashing of shortening and could result in personal injury Moving the fryer or filter drain pan while containing hot shortening is not recommended Hot shortening can splash out and severe burns could result Always wear chemical splash goggles or face shield and protective rubber gloves when cleaning the frypot as the cleaning solution is high in alkaline Avoid splashing or other contact of the solution with your eyes or skins Severe burns may result Carefully read the instructions on the cleaner If the solution comes in contact with your eyes rinse thoroughly with cool water and see a physician immediately Also to avoid overfilling the drain pan drain only 1 vat at a time The drain pan holds 1 full vat or 2 split vats of oil Overfilling the drain pan may cause slippery floors which may result in personal injury Cover adjoining vats to avoid accidentally contaminating oil Do not cook product ina adjoining vat when the cleaning process is in progress to avoid contaminating the oil and product Press and hold uni display shows 1 EXPRESS FILTER Split vat units use the left button for the left vat and the right F button for the
9. Instructions for Optional Bulk Oil Disposal System 3 17 3 15 CHANG the Filter Pad ciraceenscsacresaraeayecnsdcuueedvactane nacsseidussayeseadesucuauaeaiers 3 18 3 16 Removing and Cleaning Basket Rest cccecccccsssseseeeeceeeeeeeaseeseeeeees 3 20 SA Mes Ge cred A VO e E ASE E AES 3 21 3 18 Check Replace Filter Drain Pan O Rings s essessssseeenessssssssserrsssssseses 3 24 AS 091 6 8 10000 a ane eee one ern eee eee reer er cee 3 25 320 RIVED GOI Stas aatcsccusssanisessarpoccksasenctdsieneeadnaaninteticerocduvasesctdaieneeaaniacinds 3 25 3 21 Preventive Maintenance Schedule scssesenswsscsetudssesiatenocariudsiesasnmiacnetudssesioss 3 26 INFORMATION MODE sserrireciorredsde ranei e eeann dd or dyrene 4 1 4 1 Information Mode Details icsicsoscvrsceussanscionavnrddavecrindesaxhoambetined dausdenedndesinees 4 PRODUCT PROGRAM MODE ens ccsasasnscevessscceetssneedssevn cede bsseesavawnsecsnssancedesianst 5 1 5 1 Modifying Product Settings sa cientecepedessentencacsnedvesuynecu aati oamswnneaieseudsuecwiad 5 1 Model EEE 141 142 143 144 510 Section Section 6 Section 7 909 loka Prodsernic PENNY TABLE OF CONTENTS Continued Page LEVEC2Z PROGRAMMING oa otesceae cones ies tataveerecuevecticternaeeotenceeterertasceneeectietents 6 1 01 Special Prost amd Modo cin ss staccnscessenatsosassasnes ian EA aeaa 6 1 O2 COAR E E E E eres 6 10 6 3 Data Logging Heat Control Tech Stat and Filter Control
10. Lockout Enabled YES or NO MIXED Left Vat Filter Cycles 0 to 99 GLOBAL Right Vat Filter Cycles 0 to 99 GLOBAL Filter Lockout Enabled YES or NO GLOBAL e Polish Duration X XX M SS Change Pad Reminder Time XX HRS Clean Out Time XX MIN Clean Out Temperature XXX F or C Cooking User IO After Cook Cycle display shows previous menu item or Number of Baskets 2 BASKETS or 4 BASKETS e Show Cooking Indicator YES or NO 2nd Language English Russian Swedish SVENSKT German DEUTSCHE Portuguese Spanish ESPANOL and French FRANCAIS 2nd Audio Volume Energy Save Enabled YES or NO Fryer Type GAS or ELECTRIC Vat Type SPLIT or FULL Autolift Enabled NO LIFT or YES LIFT Bulk Oil Supply YES or NO Bulk Oil Dispose YES or NO Serial No of Fryer Change Mer Code 1 YES Change Usage Code 1 YES Dispose Requires Code YES or NO Longer Fill Time Enabled YES or NO Let User Exit Fill YES or NO 1009 H 6 1 SPECIAL PROGRAM 909 ae Y PENNY loka Foodservior Solutions MODE Continued Model EEE 141 142 143 144 Press and hold the button for 5 seconds until LEVEL 2 followed by SP PROG and ENTER CODE show in the display Enter code 1 2 3 and SP 1 TEMP FORMAT show in the displays NOUIGE If a bad code is entered a tone sounds and BAD CODE shows on the display Wait a few seconds the controls
11. Modes 6 10 IROUBLEE HOO FUN I eeren rE ERA EER E E R S 7 1 Teh Tro bleshootne Guide ssssccsroci oirir erinnern iE SE EN Ea E EEEak CINNE 7 1 P E D T A AAE E A ENN 7 3 Model EEE 141 142 143 144 ea H Y PENNY ilobal Foodservior Solutions Model EEE 141 142 143 144 1 1 INTRODUCTION 2007 1 2 PROPER CARE 1 3 ASSISTANCE 1 1 The Henny Penny reduced oil capacity open fryer is a basic unit of food processing equipment This unit is used only in institutional and commercial food service operations NOUUGE As of August 16 2005 the Waste Electrical and Electronic Equipment directive went into effect for the European Union Our products have been evaluated to the WEEE directive We have also reviewed our products to determine if they comply with the Restriction of Hazardous Substances directive ROHS and have redesigned our products as needed in order to comply To continue compliance with these directives this unit must not be disposed as unsorted municipal waste For proper disposal please contact your nearest Henny Penny distributor As in any unit of food service equipment the Henny Penny open fryer does require care and maintenance Requirements for the maintenance and cleaning are contained in this manual and must become a regular part of the operation of the unit at all times Should you require outside assistance call your local independent distributor in your area or call Henny Penny Cor
12. Section 3 3 and then press y button for YES Unit automatically goes into the Melt Cycle until the oil tem perature reaches 180 F 82 C and then control automatically exits the Melt Cycle e bypassed if desired by pressing y button or X button and holding it for 5 seconds The Melt Cycle may b The control then shows EXIT MELT YES NO Press V button for YES and vat heats continuously until the set point temperature is reached Do not bypass the Melt Cycle unless enough oil has melted to completely cover all of the elements If the Melt Cycle is bypassed before all elements are covered excessive smoking of oil or a fire will result A DANGER DO NOT OVERLOAD OR PLACE PRODUCT WITH EXTREME MOISTURE CONTENT INTO THE BASKETS 3 LBS 1 4 KG IS THE MAXIMUM AMOUNT OF PRODUCT PER FULL VAT AND 1 1 2 LBS 68 KG FOR THE SPLIT VATS FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN OIL OVERFLOWING THE VAT WHICH COULD CAUSE SERIOUS BURNS PERSONAL INJURY FIRE AND OR PROPERTY DAMAGE 510 Y PENNY Coba Foodservice Solut 3 5 BASIC OPERATION 3 6 IDLE MODE 110 Model EEE 141 142 143 144 The Evolution Elite fryer is availalble as non auto lift and auto lift models The auto lift controls allow the baskets to be automatically lowered into the shortening at the beginning of the cook cycle and raised from the shortening at the end of the cycle 1 Once out of t
13. Used to access the Program Modes used as b gt button to advance to the next parameters in Program and Filter Modes press to select 2nd languages and volumes This LED lights when the control calls for heat for the right vat s and the elements come on and heat the oil Press to turn on and off the heat system for the left vat s 3 2 P ENN loka Foodservior al Model EEE 141 142 143 144 3 1 OPERATING COMPONENTS Continued Fig No 3 1 3 1 3 1 3 1 3 1 3 2 3 3 3 4 3 3 Item No 10 amp 11 12 13 14 15 16 17 18 Function Each product button LED lights when that particular product has been selected or when it is compatible with cook temperature Press to select the desired product press to place the letters under the button during naming a product in Program Mode The can be used to start an Idle Mode if enabled in Special Program Mode During normal operation press this button to start and stop cook cycles for the right basket press to change displayed product press to confirm prompts in the filter modes also used for V to indicate YES or confirmation During normal operation press this button to start and stop cook cycles for the right basket press to change displayed product press to deny prompts in the filter modes also used for X to indicate NO or cancel Press to turn on and off the heat system for the right vat s Auto
14. V button for a few seconds Once lines are clear press X button and display shows VAT DRY YES NO Push drain knob and close drain 16 Pull drain pan from under fryer and dispose of rinse water 110 3 17 CLEAN OUT MODE Continued 3 18 CHECK REPLACE FILTER DRAIN PAN O RINGS Figure 3 110 Model EEE 141 142 143 144 17 Thoroughly dry the vat with a towel and then press the y button Controls return to normal operations Make sure the inside of the vat the drain valve opening and all the parts that come in contact with the new oil are as dryas possible 18 Make sure the drain is closed and return the filter pan assembly with new filter pad to the fryer Fill vat with oil following the Filling or Adding Oil instructions from Section 3 3 To prevent oil leaking and to keep filtering process operating properly the filter drain pan o rings should be inspected for nicks and tears at least every 3 months Figure 1 1 Open the door lift up on the drain pan stop and pull out the filter drain pan assembly using the handle on the drain pan Figures 2 amp 3 BURN RISK This pan could be hot Use protective cloth or glove or severe burns could result 2 Visually check the 3 o rings on the tube of the filter drain pan for any cracks or breaks and replace if necessary 3 To replace o ring use a small flat bladed screwdriver pry up on the o ring and pull off of end of tube Roll new o ring
15. in the diplays along with the time of day and date of the last filter 3 25 309 as H Y PENNY Coba Foodservice Solutions 3 21 PREVENTIVE MAINTENANCE SCHEDULE 510 Model EEE 141 142 143 144 As in all food service equipment the Henny Penny open fryer does require care and proper maintenance The table below provides a summary of scheduled maintenance procedures to be performed by the operator Procedure Frequency Filtering of shortening Daily Section 3 11 Changing the filter pad Daily Section 3 13 Lubricate filter pan o rings Every filter pad change Lubricate EEE 141 oil reservoir When reservoir is O rings removed Changing of oil When oil smokes foams up violently or tastes bad Cleaning the vat Every change of oil Section 3 15 Inspect filter pan o rings Quarterly Section 3 16 Inspect EEE 141 reservoir Quarterly o rings Section 3 10 H Se Y PENNY loka Foodservice Salty Model EEE 141 142 143 144 4 1 INFORMATION MODE DETAILS 4 1 This historic information can be recorded and used for operational and technical help and allows you to view the following e 1 E LOG e 9 CPU TEMP e 2 LAST LOAD e 10 COMMUNICATION INFO e 3 DAILY STATS e 11 ANALOG INFO e 4 OIL STATS e 12 ACTIVITY LOG e 5 REVIEW USAGE e 13 OIL LEVELS 6 INPUTS e 14 PUMP VALVE INFO e 7 OUTPUTS e 15 AIF INFO e 8 OIL TEMP Not all Information Mode functions are discussed in thi
16. lift equipped fryers ONLY Press to raise or lower baskets A Filter Beacon is found beside each black drain knob when lit blue indicates the oil should be filtered at this time beacon flashes when the drain needs opened or closed When the power switch is turned to the ON position power is supplied to the controls and pumps For fryers with a bulk oil supply press this button to fill the JIB 110 Model EEE 141 142 143 144 CEET E ere ce LE 0 000 0 6 8888 O E 94600000000 2 68600000000 a Z 8 Bana D a 8000040000 E 5 e i 7 i AES Figure 3 5 Fig Item Description Function No No 3 5 1 Filter Drain Pan Assy Oil is drained into this pan and then is pumped through filters to help prolong the use of the oil 3 5 2 Basket Rest The baskets hang on this when not in use or to drain the product after a cook cycle 3 5 3 Vat Covers Covers the vat when not in use 3 5 Drain Knob Pull out on black knobs to open drain valve and oil drains from vat Push in to close drain valve and oil can be pumped into vat 3 5 5 JIB Jug in a Box holds oil to be pumped into vats to top off the oil level by the Oil Guardian process 909 3 4 a H Y PENNY lobe Foodservior Solutions 3 2 SET UP MODE 3 5 Model EEE 141 142 143 144 Upon initial start up the controls will ask to confirm the settings for the fryer When the main power switch is turned on OFF
17. o E r 2 1 2 1 TA OCU E CO 1 E E E E O 2 1 P E o E EEA EEE E E E A AT 2 1 2 3 Selecting the Fryer Location prsncrsccaniscecedsaeeectrlatecedanicnsccanieceetdsaevecdtubasest 2 2 De E MNS Te Ci T E E E N 2 2 2 9 Ventilation ot Iyer sacraccanaccinetsierocaksasnssed sic inisenisi tie rocduenseeetstieneeadnincint 2 3 20 ElecticalRegremeniS sd eciezsnacsutudusrsgss racsweudnacciacsuncnvoudusenaes aceuudaseaiets 2 3 2e DIe ONS senere SE EE EEEE AEE E Ae 2 5 OPERATION seasann aE EEIN ESA AE EE EEE 3 1 3 1 Operan COMIPOMCINES sisirin dsi sare dude u tede EdE EENEN KOREEN EANES 3 1 3A CUP MOde sssrini ienet nner rR Erie orea erorii EKITEA ERE adai 3 5 39 Piling OP ACG Oll ecese ae nA i e EELEE 3 6 3 4 Morning Start Up Procedures ss sccssscvestsavscnncsscaxnaddsnisnnccksnscieridanssatasssasiaes 3 7 IS ASIC Op O E EA EES 3 8 IE MEMO e E E EAE E eee 3 8 3 7 Oil Guardian Auto Top OfP cincinscsicaunssnscxancesiratuaetonianceseectracescuandssiees 3 9 3 8 Selecting Product with Different Setpoint cccccccsssesseeeeeeeeeeeeeeeeees 3 9 39 Rephcme TU saa raceecdeetedncunteccedvesunneunesectedsesnyanuiasaeieduuenanacsacsstudsvesiees 3 9 3 10 Model EEE 141 Oil Reservoit sess ccaniscocessscvsccerbatoncdacnsccavlsdeetdsaevecdsuhaterds 3 10 3 11 Smarte ter Express M sassari ap an aE EAEE ra iR ISEE 3 11 I2 DaN CINO seeen iE einni En ei E EAE EEEE i 3 13 3 13 Discarding Oil from Vat Using Optional Discard Shuttle eee 3 16 3 14 Operation
18. sensors high limits fittings and hardware will be the responsibility of the owner Any claim must be presented to either Henny Penny or the distributor from whom the appliance was purchased No allowance will be granted for repairs made by anyone else without Henny Penny s written consent If damage occurs during shipping notify the sender at once so that a claim may be filed THEABOVE LIMITED WARRANTY SETS FORTH THE SOLE REMEDY AGAINST HENNY PENNY FOR ANY BREACH OF WARRANTY OR OTHER TERM BUYER AGREES THAT NO OTHER REMEDY INCLUDING CLAIMS FOR ANY INCI DENTAL OR CONSEQUENTIAL DAMAGES SHALL BEAVAILABLE The above limited warranty does not apply a to damage resulting from accident alteration misuse or abuse b if the equipment s serial number is removed or defaced or c for lamps and fuses THE ABOVE LIMITED WARRANTY IS EX PRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING MERCHANTABILITY AND FIT NESS AND ALL OTHER WARRANTIES ARE EXCLUDED HENNY PENNY NEITHER ASSUMES NOR AUTHORIZES ANY PERSON TO ASSUME FOR ITANY OTHER OBLIGATION OR LIABILITY Revised 01 01 07 FM05 053 F 9 19 10 loka Prodsernic Section Section 1 Section 2 Section 3 Section 4 Section 5 Y PENNY e Rafietions TABLE OF CONTENTS Page INTRODUCTION aree r E E 1 1 1 1 TOU CM OR AOE EEE A EE O E ETE EE 1 1 Me Bi e E E SE 1 1 DS PRS EN pect cc passions es tatnces oece eee A 1 1 arsed ates E EE E 1 2 ID STON
19. temperature which helps to keep the oil from over shooting the setpoint temperature Press the product buttons or the and W buttons to change this value of 0 to 50 degrees e Use lt button to go back to previous menu items e Press gt button when finished with the current product to return to the SELECT PRODUCT step e Press and hold button to exit PRODUCT PROGRAM Mode 5 3 H ae Y PENNY Coba Foodservior Solutions Model EEE 141 142 143 144 Used to access the following 6 1 SPECIAL PROGRAM MODE e Special Program Mode e Tech Mode e Clock Set e Stats e Data Communication e Filter Control e Heat Control The Special Program Mode is used to set more detailed programming such as SP 1 SP 2 SP 3 SP 4 SP 5 SP 6 SP 7 SP 7A SP 7B SP 7C SP 8 SP 8A SP 8B SP 8A SP 8B SP 8C SP 9 SP 10 SP 11 SP 12 SP 13 SP 14 SP 15 SP 16 SP 17 SP 18 SP 19 SP 20 SP 21 SP 22 SP 23 SP 24 SP 25 SP 26 SP 27 SP 28 SP 29 e Degrees Fahrenheit or Celsius e Language English Russian Swedish SVENSKT German DEUTSCHE Portuguese Spanish ESPANOL and French FRANCAIS System Initialization Factory Presets Audio Volume Audio Tone Melt Cycle Select 1 LIQUID 2 SOLID Idle Mode Enabled YES or NO e Use 0 for IDLE e Auto Idle Minutes Idle Set point Temperature e Filter Tracking Mode 1 MIXED or 2 GLOBAL e Suggest Filter At 75 to 100 MIXED e Filter
20. used for several minutes the controls can be set to automatically lower the oil temperature or press the button to start the Idle Mode e The oil is maintained at a lower temperature until the button is pressed and then the oil is heated to cooking temperature See Special Program Modes SP 12 SP 13 amp SP 14 3 8 PENNY loka Foodservior San 3 7 OIL GUARDIAN Auto Top Off 3 8 SELECTING A PRODUCT WITHA DIFFERENT SETPOINT 3 9 REPLACING THE JIB Figure 1 Model EEE 141 142 143 144 During normal operation the control automatically monitors the oil level in the vat If the control senses the oil level too low the unit automatically pumps oil from the JIB into the vat to keep the oil at the proper level Manual Top Off If the oil level is a little low oil can be added to the vat at any time from the JIB to raise the oil level to the proper level by following the steps below This procedure is NOT to be used to fill an empty vat 1 Press and hold LF until display shows FILTER MENU along with 1 EXPRESS FILTER 2 Press gt 5 times until 6 FILL FROM JIB shows in the display 3 Press V button and display shows PUMP and EXIT 4 Press and hold V button and display shows FILLING and the oil is pumped from the JIB to the vat 5 Once frypotis full release V button and display returns to PUMP and EXIT Press X button twice to return to
21. vat from the JIB Press X button and controls return to normal operation 110 PENNY Coba Foodservior Solutions 3 13 DISCARDING OIL FROM VAT USING OPTIONAL OIL DISCARD SHUTTLE Figure 3 909 Model EEE 141 142 143 144 A DANGER FIRE HAZARD WITH PROLONGED USE THE FLASHPOINT OF OIL IS REDUCED DISCARD OIL IF IT SHOWS SIGNS OF EXCESSIVE SMOKING OR FOAMING SERIOUS BURNS PERSONAL INJURY FIRE AND OR PROPERTY DAMAGE COULD RESULT Open the door lift up on the drain pan stop and pull out the drain pan assembly using the handle on the drain pan Figures amp 2 Press and hold either one until display shows FILTER MENU along with 1 EXPRESS FILTER Press and release gt button twice until display shows 3 DISPOSE Press V button and display shows DISPOSE YES NO Press V button and IS DISPOSAL UNIT IN PLACE YES NO shows in display If Bulk Oil Dispose is set to YES DRAIN VAT YES NO shows in display With discard shuttle rolled into place Figure 3 press V button and display shows OPEN DRAIN Pull out on drain knob to open drain and display shows DRAINING Oil now drains from the vat into the shuttle Display shows VAT EMTY YES NO Verify that vat is empty and press V button Display shows CLN VAT COMPLETE YES NO Once vat is clean press V button and display shows CLOSE DRAIN Push in
22. 11 Model EEE 141 142 143 144 Be sure that the drain pan bottom screen crumb catcher and the retaining ring are thoroughly dry before placing filter pad into pan as water will dissolve the filter pad Reassemble in reverse order placing the bottom screen into the filter pan first followed by the filter pad retaining ring and the crumb catcher Before pushing the filter drain pan back into position lubricate the o rings Figure 9 on the filter tube with cold oil Check o rings for tears or nicks and replace if necessary See Section 3 16 Push the filter pan assembly back underneath the fryer making sure the filter tube on the pan makes a good connection with the fitting underneath the fryer Figure 9 Make sure the drain pan stop is engaged and the fryer is now ready for normal operation Figure 10 The basket rest on the rear shroud of the fryer should be removed and cleaned periodically BURN RISK Use protective gloves when removing the basket rest The basket rest may be hot and burns could result Grasp the basket rest with 2 hands and pull it off the key ways Take it to a sink and clean it with soap and water Dry thoroughly Clean the area behind the basket rest and then reinstall the basket rest 3 20 CLEAN OUT MODE 3 17 Y PE loka Prodsernioe San iir NNY 6o W 3 21 CHEMICAL SPLASH GOGGLES CHEMICAL RESISTANT GLOVES Model EEE 141 142
23. 27 is set to YES Press V button and DRAIN VAT YES NO shows in display Press X button if drain pan already has oil in it Skip to step 8 Press V button and display shows OPEN DRAIN Pull out on drain knob to open drain and display shows DRAINING Oil now drains from the vat into drain pan Display shows VAT EMTY YES NO Verify that vat is empty and press V button Display shows CLN VAT COMPLETE YES NO Once vat is clean press V button Display shows DISPOSE and then s PUMP X DONE Press V button and oil is pumped from the drain pan to the bulk oil container When all the oil is pumped from the pan press X button STOP Display shows DISPOSE and then V PUMP X DONE Press X button and close drain Display shows MANUAL FILL VAT or FILL VAT FROM BULK if equipped followed by IS POT FILLED along with YES NO Fill the vat to the lower indicator line on the rear of the vat and then press V button See Filling or Adding Oil instructions from Section 3 3 Fryer returns to normal operation 1009 PAD 209 Model EEE 141 142 143 144 In order to assure good oil pumping performance the filter pad or paper should be changed at least once per day If the filter pad has not been changed a reminder shows on the display CHANGE PAD Press y button to cancel the message but it reappears every 4 minutes until the f
24. 9 F MO 5 O 5 3 F i Henny Penny Corp Eaton Ohio 45320 Revised 5 19 10 Y PENNY Global Foodservice Solutions Henny Penny Corporation P O Box 60 Eaton OH 45320 1 937 456 8400 1 937 456 8402 Fax Toll free in USA 1 800 417 8417 1 800 417 8434 Fax www hennypenny com
25. ER PAD YES NO If changing the filter pad at this time press V and change filter pad following the procedures in the Changing the Filter Pad Section Controls return to normal operation If filter pad is to be changed at a later time press X button and CHANGE FILTER PAD reminder shows 15 minutes later During the next SmartFilter Express with a new filter pad if the vat is not filled after 3 tries the display shows FILTER SERVICE REQUIRED SEE TROUBLESHOOTING GUIDE If the Service Required message appears then every 15 minutes the display shows FILTER PROBLEM FIXED YES NO If the problem has not been fixed press X button Once the problem has been resolved press V and controls return to normal operation To help ensure the vat fills completely make sure filter pan is cleaned at least daily filter pad is changed make sure JIB is full and that O rings on the filter pan are in good condition 3 12 PENNY Model EEE 141 142 143 144 loka Foodservior San 3 12 DAILY FILTERING This filtering procedure allows for a more thorough cleaning of the vat and should be done once a day The vat can be filtered during any non frying times BURN RISK To avoid burns from hot oil use approved safety equip ment including apron face shield and gloves before starting filtering procedure Also to avoid overfilling the drain pan drain only 1 vat at atime The drain pan
26. FRYER LOCATION 2 4 LEVELING THE FRYER 2 2 Model EEE 141 142 143 144 The proper location of the fryer is very important for operation speed and convenience The location of the open fryer should allow clearances for servicing and proper operation Choose a location which will provide easy loading and unloading without interfering with the final assembly of food orders Operators have found that frying from raw to finish and holding the product in warmers provides fast continuous service Keep in mind the best efficiency will be obtained by a straight line operation 1 e raw in one side and finished out the other side Order assembly can be moved away with only a slight loss of efficiency FIRE HAZARD To avoid fire and ruined supplies the area under the fryer should not be used to store supplies BURN RISK To prevent severe burns from splashing hot oil position and install fryer to prevent tipping or movement Restraining ties may be used for stabilization For proper operation the open fryer should be level from side to side and front to back Using a level placed on the flat areas around the vat collar on the middle well and then adjust the casters until the unit is level 1108 2 5 VENTILATION OF FRYER 2 6 Y PENNY Global Foodser 6 ELECTRICAL 1108 REQUIREMENTS Model EEE 141 142 143 144 The fryer should be located with provision for venting into adequate exhaust hood or ven
27. NO and the display shows CLOSE DRAIN Push in on the drain knob to close the drain Figure 3 and the display shows RINSING and vat fills with oil Once the vat is filled OPEN DRAIN shows in display Pull out on drain knob to open the drain Figure 4 and display shows RINSING When rinsing is complete display shows RINSE AGAIN YES NO 3 14 H 3 12 DAILY FILTERING 3 15 as Y PENNY loka Foodserelor Continued 13 14 iD Model EEE 141 142 143 144 Press V button for YES if another rinse is needed otherwise press X button for NO The display shows POLISH YES Press V button for YES and the oil is polished by circulating it through the filtering system The display shows 5 00 STOP POLISH If desired press V button to stop the polishing otherwise the oil is polished for 5 minutes Once the oil is polished the display shows FILL VAT YES Press V button and display shows CLOSE DRAIN Push in on the drain knob to close the drain Figure 3 the display shows FILLING and the vat then re fills with oil Once full the display shows IS POT FILLED YES NO Press V button for YES and fryer returns to normal operation If X button is pressed the display shows FILLING You can try to fill the vat 4 times and then the control shows ADD QUIT Press V button and JIB pump runs 60 seconds filling the
28. Waste Electrical and Electronic Equipment WEEE Symbol Shock Hazard Symbols Hot Surface Symbols Pinch Point Symbol Auto Lift Fryers 310 ENNY Model EEE 141 142 143 144 Coba Foodservior Solutions 2 1 INTRODUCTION This section provides the installation and unpacking instructions for the Henny Penny open fryer Installation of this unit should be performed only by a qualified service technician SHOCK HAZARD Do not puncture the fryer with any objects such as drills or screws as component damage or electrical shock could result 2 2 UNPACKING WAG ay INSTRUCTIONS N Oji GE Any shipping damage should be noted in the presence of the delivery agent and signed prior to his or her departure 1 Caut and remove the metal bands from the carton 2 Remove the carton lid and lift the main carton off the fryer 3 Remove corner packing supports 4 4 Cutthe stretch film from around the carrier rack box and remove it from the top of the fryer lid 5 Cutand remove the metal bands holding the fryer to the pallet Remove filter drain pan and JIB shelf from fryer before removing fryer from pallet or damage to the unit could result Figure 1 6 Remove the fryer from the pallet Figure 1 HEAVY OBJECT Take care when moving the fryer to prevent personal injury The fryer can weigh up to 800 Ibs 363 kg 510 2 1 Y PENNY Coba Foodservior San 2 3 SELECTING THE
29. YES if the oil is pumped into the vats from an outside oil reservoir Otherwise set SP 22 to NO Bulk Oil Disposal SP 23 Press gt button and SP 23 BULK OIL DISPOSE flashes in the left display Press the 4 amp or W buttons to choose YES DISP or NO DISP Set to YES DISP if the oil is pumped from the vats to an outside oil reservoir when disarding the oil Otherwise set SP 23 to NO DISP Serial Number Log SP 24 Press j gt button and SP 24 and S N VEDIT flash in the displays along with the serial number of the unit THIS SERIAL NUMBER SHOULD MATCH THE SERIAL NUMBER ON THE DATA PLATE ON THE DOORS IF NOT IT CAN BE RECORDED Program Code Change SP 25 This allows the operator to change the program code factory set at 1 2 3 used to access Product Programming and Level 2 Program Mode Press j gt button and SP 25 and CHANGE MGR CODE 1 YES flash in the display Press and ENTER NEW CODE P DONE I QUIT show scrolls through the display Press the product buttons for new code If satisfied with code pressi and REPEAT NEW CODE P DONE I QUIT shows in display Press same code buttons 6 8 H 6 1 SPECIAL PROGRAM 6 9 ae Y PENNY loka Foodservior Solutions MODE Continued Model EEE 141 142 143 144 Program Code Change SP 25 Continued If satisfied with code press and CODE CHANGED shows in display If not satisfied with co
30. and avg of last 4 batches of oil DETAILS Continued Press gt and 4 OIL STATS show in displays Press W button to start viewing the cook data FUNCTION DISPLAY EX Number of times filter skipped 8 Number of cook cycles on this oil L R TOT CK 3 Average number of days per oil change L R AVG DAYS PER OIL CHANGE 13 8 DAYS Average number cook cycles per oil change L R AVG CKS PER OIL CHANGE 388 CKS Press and hold a product button 1 to 4 to view the data from one of the previous 4 batches of oil used Press on view oldest oil data Ex OIL 4 14 DAYS Press to view 3rd oldest oil data Ex OIL 3 12 DAYS 6 Press to view 2nd oldest oil data Ex OIL 2 15 DAYS Press to view previous batch of oil Ex OIL 1 13 DAYS 309 4 4 oe HENNY PENNY Model EEE 141 142 143 144 4 1 INFORMATION MODE 5 REVIEW USAGE accumulated info since the data was reset DETAILS Continued Press gt and 4 REVIEW USAGE show in displays Press W button to start viewing the cook data FUNCTION DISPLAY EX Day the usage data was previously reset SINCE APR 19 3 00P Number of Hours the fryer was on R ON HRS Number of times filtered L R FILTERED Number of times filter skipped R SKIPPED umber of times oil added L R ADD OIL L R DISPOSE L R TOT CK QUIT CK COOK 2 OOK 3 COOK 4 OOK 5 OOK 6 COOK 7 OOK 8 COOK 9 COOK 0 Reset usage data Enter the Usage Code 1 2 3 RESET USAGE o
31. anges toa C Once the desired letter shows in the display press gt button to continue to the next letter and repeat the procedure Press and hold the right X button to exit Program Mode or press gt button to continue on to COOK TIME Assign Button 6 Press b gt button until ASSIGN BTN shows in the display along with the product ex NUGGETS If this product already has a product button assigned to it that LED will be lit To assign other product buttons to that product press and hold the product button for 3 seconds and that LED stays lit To remove a product from a button press and hold the product button with a lit LED and the LED goes out 309 5 1 H 5 1 MODIFYING PRODUCT 5 2 _ oa Y PENNY madiernice daltons Coba Produ SETTINGS Continued Model EEE 141 142 143 144 To Change Times and Temperatures 7 Press gt button until COOK TIME shows in the display and then use the product buttons or the and W buttons to change the time in minutes and seconds to a maximum of 59 59 8 Press gt button and TEMP shows in the display along with the preset temperature on the right side of the display Press the product buttons or the amp and W buttons to change the temperature The temperature range is 190 F 88 C to 375 F 191 C Cook ID Change 9 Press ie button until COOK ID shows in the display along with the product ID For example NUG w
32. de press and CANCEL shows in display then reverts back to SP 25 and CHANGE MGR CODE 1 YES Now the above steps can be repeated Usage Code Change SP 26 This allows the operator to change the reset usage code factory set at 1 2 3 to reset the usage amounts of each product See Review Usage step in Information Mode Press gt button and SP 26 CHANGE USAGE CODE 1 YES flashes in the display Press 4 and ENTER NEW CODE P DONE I QUIT show scrolls through the display Press the product buttons for new code If satisfied with code press and REPEAT NEW CODE P DONE I QUIT shows in display Press same code buttons If satisfied with code press CODE CHANGED shows in display If not satisfied with code press and CANCEL shows in display then reverts back to SP 26 and CHANGE USAGE CODE 1 YES Now the above steps can be repeated Dispose Requires Code SP 27 Press gt button and SP 27 DISPOSE REQUIRES CODE flashes in the left display Press the AX or W buttons to choose YES or NO If set to YES code 1 2 3 must be entered to discard the oil from the vat using the Dispose Mode Longer Fill Time SP 28 Press j gt button and SP 28 LONGER FILLTIME ENABLED flashes in the left display Press the M or W buttons to choose YES or NO Let User Exit Fill SP 29 Press button and SP 29 LET USER EXIT FILL flashes in the left display Press the MA o
33. e sensor checked amp replace if necessory 209 7 3 oe HENNY PENNY Model EEE 141 142 143 144 7 2 ERROR CODES DISPLAY CAUSE CORRECTION Slow heat recovery Have a certified service technician check the fryer for correct voltage to the unit have the contactors and heating element checked have unit checked for loose or burnt wires E 22 NO HEAT Elements not Check power cord and heat circuit CHECK PWR heating CORD AND BREAKER Lower elements completely back into the vat E 41 E 46 Turn switch to OFF then back to ON if display shows any of these error codes have the controls re initialized 1f error code persists have the control board replaced E 47 Analog converter Turn switch to OFF then back to ON if E 47 persists chip or 12 volt have the I O board or the PC board replaced if speaker supply failure tones are quiet probably I O board failure have the I O board replaced E 48 Input system Turn switch to OFF then back to ON have controlPC board error replaced if E 48 persists E 54C Temperature input Turn switch to OFF then back to ON have control PC board error replaced if E 54C persists E 60 AIF PC board not Press power button to vat off and back on again if E 600 communicating with persists have the connector between the PC boards checked control PC board replace AIF PC board or control PC board if necessary 7 4 90
34. er 3 EURO or 4 FSA US before 2007 The Data Logging Heat Control Tech Stat and Filter Control Modes are advanced diagnostic and program modes mainly for Henny Penny use only For more information on these modes contact the Service Department at 1 800 417 8405 or 1 937 456 8405 Model EEE 141 142 143 144 7 1 TROUBLE SHOOTING GUIDE POWER switch ON but e Open circuit e Plug fryer in fryer completely inoperative e Check breaker or fuse at supply box e Circuit breakers in fryer tripped Open left door and reset circuit breakers on fryer See below e Open high limit circuit e Reset the high limit by using a small screwdriver or Allen wrench gently pushing it into the hole in the heating element hinge if high limit does not reset Control error code E 10 high limit may need replaced e JIB is low or empty e Fill the JIB JIB oil line is cloggedor Check JIB line collapsed e Check JIB tube amp connection e Filter pan needs cleaned Clean filter pan and change paper or pad Vat 1s under filled 209 7 1 PENNY Coba Foodservior Solutions 7 1 TROUBLE SHOOTING GUIDE Continued Model EEE 141 142 143 144 Oil foaming or boiling over top of vat Oil will not drain from vat Filter motor runs but pumps oil slowly Bubbles in oil during entire filtering process Filter motor will not run e Water in oil Improper or bad oil e Improper filtering e Impro
35. he cook cycles must be completed before the control suggest filtering Press gt and SP 8B and LOCKOUT ENABLED shows in the left display Press the and W buttons to choose YES or NO If set to YES when the controls suggest filtering FILTER LOCKOUT YOU MUST FILTER NOW shows in the display and it refuses further cook cycles until the vat 1s filtered Press gt and SP 8C and LOCKOUT AT shows in the left display and a value between 100 and 250 shows on the right display Press the A and Wouttons to change this value The lower the value the sooner the lockout occurs Ex If set at 100 lockout occurs when the cycle counts reaches 1 or greater Set at 200 twice as many cycles are counted before lockout occurs See example above 6 4 H 6 1 SPECIAL PROGRAM 6 5 as Y PENNY loka Foodservice Solut MODE Continued Model EEE 141 142 143 144 Filter Tracking Mode SP 8 Continued GLOBAL If GLOBAL is selected press button Split Vat If unit is a split vat SP 8A and LEFT VAT FILTER CYCLES shows in the left display and the number of cook cycles between filters shows on the right display 0 to 99 Use A and W or product buttons to change this number Press gt button and SP 8B and RIGHT VAT FILTER CYCLES shows in the left display and the number of cook cycles between filters shows on the right display 0 to 99
36. he Melt Cycle LOW TEMP flashes until the set point temperature has been reached No cook cycles can be started while LOW TEMP shows in the display Once the set point temperature has been reached the product name now shows in the display ex FRY and product now can be placed in the oil 2 Press a timer button or Auto lift fryers the basket automatically lowers into the shortening 3 Display shows the name of the product cooking ex FRY and the timer counting down 4 When cook cycle is complete and alarm sounds and display shows DONE 5 Press the timer button under DONE to stop the alarm and lift basket from vat Auto lift fryers the basket automatically rises out of the shortening 6 Ifa Quality Timer hold timer has been programmed the hold time starts automatically when the user presses the timer button to end the cook cycle While the quality timer counts down the display shows the three digit product abbreviation followed by Qn where n is the number of minutes remaining ex FRY QS FRY QS FRY Q8 etc At the end of the timer countdown the control beeps and the display shows QUAL followed by the three digit product name QUAL FRY QUAL FRY Press the timer button to cancel the timer Once programmed an Idle Mode can help to save on oil and utility costs If the fryer is not being
37. hen heated Figures 1 amp 2 3 Place basket support inside of vat and fill vat with cold oil to the lower indicator Figure 3 Filling Vat from Bulk Supply Must be equipped with optional accessories amp controls set to YES for Bulk Oil Supply in Set Up Mode 1 Turn the main power switch to the ON position 2 Place basket support inside of vat Figure 3 3 Press and hold G on either side until display shows FILTER MENU along with 1 AUTO FILTER 4 Press and release button 6 times until display shows 7 FILL POT FROM BULK 5 Press V button and display shows FILL VAT and then 4 PUMP X DONE Press and hold V button again to fill vat and display shows FILLING 6 Once oil is to the lower fill line release V button and display returns to FILL VAT V PUMP X DONE Press X button twice to return to normal operation Press and hold the black button behind the right door to fill the JIB from the Bulk Supply as needed Figure 3 3 6 H 3 4 MORNING START UP PROCEDURES 3 7 as Y PENNY loka Foodservior San Model EEE 141 142 143 144 Make sure basket support is in vat and the vat is filled with oil to the proper level Model EEE 141 fill the oil reservoir See Section 3 10 Move power switch to the ON position and then press to turn on heat for the desired vat If display shows IS POT FILLED make sure oil is at the proper level see
38. holds 1 full vat or 2 split vats of oil Overfilling the drain pan may cause slippery floors which may result in personal injury 1 Check Filter Pan A new filter pad should be used on the first filter of each day but the same filter pad can be used the rest of the day except for fish vats After filtering a fish vat it is recommended to change the filter pad Make sure that the filter pan cover is in place the filter drain tube is secured and the filter drain pan is pushed in and locked into place If the filter drain pan and cover are not latched into place the display shows CHK PAN i 2 Press and hold GG until display shows 1 EXPRESS Figure 1 gt FILTER Split vat units use the left button for the left vat and the right F button for the right vat 3 Press gt button and display shows 2 DAILY FILTER 4 Press V button for YES and display shows CONFIRM followed by YES NO 5 Press V button for YES and display shows OPEN DRAIN Pull out on the drain knob Figure 1 the display shows DRAINING and the oil drains from the vat or press X button for NO and controls return to normal operation 3 13 110 PENNY Coba Foodservior Solutions 3 12 DAILY FILTERING 6 Continued i a y j li nity tm l i if l f P E 2 a f A Lene j a L AERES T 7 E ga ANT p waa i T tf i ft ay ja al ae its Niall Fj GF i
39. ilter pad has been changed 1 Make sure the main power switch is in the ON position 2 Open the door lift up on the drain pan stop and pull out the drain pan assembly using the handle on the drain pan Figures amp 2 BURN RISK This pan could be hot Use protective cloth or glove or severe burns could result If the filter pan is moved while full of oil use care to prevent splashing or severe burns could result 3 Liftthe pan cover from the drain pan Figure 3 4 Lift the crumb basket from the drain pan Wipe the oil and crumbs from the crumb basket Clean the crumb basket with soap and water then thoroughly rinse with hot water and dry Figure 4 3 18 3 15 CHANGING THE FILTER PAD Continued 3 19 Model EEE 141 142 143 144 5 Remove the filter pad retaining ring and clean thoroughly with soap and water Rinse thoroughly with hot water and dry Figure 5 6 Pull the filter pad from the pan and discard pad Figure 6 7 Remove the bottom screen from pan and clean thoroughly with soap and water Rinse thoroughly with hot water and allow to air dry Figure 7 8 Wipe the oil and crumbs from the drain pan Clean the drain pan with soap and water then thoroughly rinse with hot water and dry Figure 8 209 PENNY Salriions Coba Foodservicr 3 15 CHANGING THE FILTER PAD Continued Figure 10 3 16 REMOVING AND CLEANING BASKET REST 209 10
40. into notch on tube Before pushing the filter drain pan back into position lubricate the o rings on the filter tube with fresh cold oil gt Figure 4 H Y PENNY Model EEE 141 142 143 144 loka Foodservior San 3 19 INFO BUTTON STATS Actual Oil Temperature 1 Press and the actual oil temperature shows in the display for each vat Set point Temperature 2 Press twice and SP shows in the display along with the set point preset temperature of each vat Recovery Information for each Vat 1 Press 3 times and REC shows in the left display and the recovery time that oil temperature went from 250 F 121 C to 300 F 149 C shows in the right display For example REC 5 30 means it took 5 minutes and 30 seconds for the oil temperature to recover to 300 F 149 C from 250 F 121 C If no buttons are pressed within 5 seconds in any of stats modes the controls revert back to normal operation 3 20 FILTER BUTTON STATS Cook Cycles Remaining before Filtering 1 Press and release either F button and the left display shows COOKS REMAINING and the right display shows the number of cook cycles before the next auto filter For example r Pe REMAINING 3 6 means after 3 more cook cycles on the left vat the controls asks the operator if they are ready to filter or not But 6 more cook cycles remain on the right vat Time and Date 2 Press either F twice and FILTERED shows
41. k cycles is reached FILTER LOCKOUT YOU MUST FILTER NOW shows in the display and it refuses further cook cycles until the vat is filtered 909 H Y PENNY Model EEE 141 142 143 144 Coba Produ 6 1 SPECIAL PROGRAM Polish Duration SP 9 MODE Continued Press gt button and SP 9 and POLISH TIME flash in the left display Press the or W or use product buttons to change the polish time from 0 to 10 minutes Change Filter Pad Reminder Time SP 10 Press j gt button and SP 10 CHANGE PAD REMINDER flash in the left display Press the 4 amp or W or use product buttons to change the time from 0 hours to a maximum of 100 hours Clean Out Time SP 11 Press gt button and SP 11 CLEAN OUT TIME flashes in the left display Press the M or Wor use product buttons to change the time from 0 to 99 minutes Clean Out Temperature SP 12 Press gt button and SP 12 CLEAN OUT TEMP flashes in the left display Press the AX or W or use product buttons to change the temperature from 0 to 195 F 90 C Cooking User IO SP 13 Press gt button and SP 11 and COOKING USER IO flash in the display Press the 4 amp or W buttons to choose SHOWPREV or SHOW Setting SP 11 to SHOWPREV means after a cook cycle the display shows the last menu item cooked SHOW means after a cook cycle shows in the display and a menu item needs selected before s
42. lation will be repaired or replaced without charge F O B factory Eaton Ohio or F O B authorized distributor The warranty for new equipment covers the repair or replacement of the defective part and includes labor charges and maximum mileage charges of 200 miles round trip for a period of one 1 year from the date of original installation The warranty for replacement parts covers only the repair or replacement of the defective part and does not include any labor charges for the removal and installation of any parts travel or other expenses incidental to the repair or replacement of a part EXTENDED FRYPOT WARRANTY Henny Penny will replace any frypot that fails due to manufacturing or workmanship issues for a period of up to seven 7 years from date of manufacture This warranty shall not cover any frypot that fails due to any misuse or abuse such as heating of the frypot without shortening 0TO3 YEARS During this time any frypot that fails due to manufacturing or workmanship issues will be replaced at no charge for parts labor or freight Henny Penny will either install a new frypot at no cost or provide a new or reconditioned replacement fryer at no cost 3TO7 YEARS During this time any frypot that fails due to manufacturing or workmanship issues will be replaced at no charge for the frypot only Any freight charges and labor costs to install the new frypot as well as the cost of any other parts replaced such as insulation thermal
43. n fryer cleaner and mix thoroughly Then press V button and display shows START CLEAN YES NO Press V button and display shows CLEANING and a count down timer Heat regulates to 195 F 91 C for this step for one hour Add water as needed during cleaning process to keep solution 1 in 25 mm above the top fill line To stop the cleaning cycle early press X button The display shows QUIT DEEP CLN YES NO Press the V button to cancel the rest of the countdown time and proceed to the rinse steps Using the open fryer brush never use steel wool scrub the inside of the vat At the end of the one hour display shows CLEAN DONE and beeps Press V button and display then shows REMOVE SOLUTION FROM VAT Empty filter drain pan of internal filtering components and take the components to a sink to be cleaned Return the empty filter drain pan and cover to the fryer making sure it is pushed into placed and the latch engaged Drain cleaning solution into the filter drain pan and pull drain pan from unit and dispose of the solution 3 22 PENNY Coba Foodservice Solutions 3 17 CLEAN OUT MODE Continued 3 23 Model EEE 141 142 143 144 BURN RISK To avoid burns when pouring hot solution wear gloves and protective gear and take care to avoid splashing 11 Return empty filter drain pan to fryer and press V button Display then shows VAT EMTY YES NO 12
44. n this step to zero out all the ENTER CODE usage information m O gt gt is Q Q QO eae ey SI bo JOO O Q Un Q naQ oj o o a Oo 4 5 309 a HENNY PENNY Model EEE 141 142 143 144 Coba Foodservicr This mode allows you to program the following e Change Product Name e Include in Filter Count Global e Assign Button e Filter at X no of loads Mixed e Change Times amp Temp e Load Compensation e Change Cook ID e Load Compensation Reference e Alarms e Full Heat e Quality Timers e PC Factor 5 1 MODIFYING PRODUCT 1 Press and hold button until PROG shows in the SETTINGS display followed by ENTER CODE 2 Enter code 1 2 3 first 3 product buttons PRODUCT and PROGRAM show in the displays followed by SELECT PRODUCT and P 1 ex NUG Change Product Names 3 Use the and W buttons to scroll through the 40 products or press the desired product button 4 Press b gt button and NAME shows in the left display and the product ex NUGGETS shows in the right display 5 Press V button and the first letter in the name flashes Press a product button and the flashing letter changes to the first letter under the product button that was pressed For example if is pressed the flashing letter changes to an A Press the same button again and the flashing letter changes to a B Press it again and the flashing letter ch
45. normal operation When selecting a product if XXX XXX shows in the display the setpoint temperature is not correct for this product To change the setpoint temperature for the desired product 1 Press product button for o FRY 2 Display shows XXX XXX e 3 Press and hold a timer button or for 5 seconds and then FRY shows in display 4 Allow oil temperature to reach setpoint temperature before dropping product 1 Control displays JIB IS LOW and an alarm sounds 2 Open right door and pull JIB from unit Pull the cap from top of JIB and discard empty JIB and replace with full one Figure Model EFE 141 single well see next section 510 PENNY Model EEE 141 142 143 144 Coba Foodservice Solutions 3 10 MODEL EEE 141 OIL Filling Oil Reservoir RESERVOIR 1 Control displays JIB IS LOW and an alarm sounds 2 Open door and pull reservoir forward and remove reservoir cover Figure 1 3 Place on bracket on door Figure 2 4 Pour oil into reservoir upto the fill lines 13 Ibs 6 12 kg and then replace cover and push reservoir back into position Figure 3 Removing Cleaning Reservoir 1 Open door and pull reservoir forward 2 Slide reservoir to the left and lift from fryer Figure 4 3 Clean reservoir at a sink with soap and water Before placing the reservoir back into position lubricate the o rings below on the filter tube with cold oil Check
46. o rings for tears or nicks and replace if necessary To replace o ring use a small flat bladed screwdriver pry up on the o ring and pull off of end of tube See below ay v J iy Figure 510 3 10 ENNY Coba Foodservior Solutions 3 11 SMARTFILTER EXPRESS 1 Figure 1 2 3 Figure 3 4 5 3 11 Model EEE 141 142 143 144 During normal operation and after a certain number of cook cycles the Filter Beacon illuminates on the front of the fryer Figure and the control periodically shows FLTR NOW YES NO If X for NO is pressed fryer resumes normal operation and control suggests filter later Check Filter Pan If the filter drain pan or cover is not inplace the display shows CHK PAN Make sure that thefilter pipe is tightly connected and that the filter drain pan is asfar back under fryer as it will go and the filter pan cover 1s in place Press V button for YES and display shows SKIM VAT followed by CONFIRM YES NO Press V button for YES and display shows OPEN DRAIN Pull out on thedrain knob Figure 2 the display shows DRAINING and theoil drains from the vat To avoid overfilling the drain pan drain only 1 vat ata time The drain pan holds 1 full vat or 2 split vats of oil Overfilling the drain pan may cause slippery floors which may result in personae in jur If filtering is NOT desired press
47. olume shows in the right display To select the volume press the V button under the desired volume Engery Save Mode SP 18 Press gt button and SP 18 ENERGY SAVE ENABLED flashes in the left display Press the amp orW_ buttons to choose YES or NO If set to YES during times of non use the fryer automatically starts an Energy Save Mode which turns off the blowers Then once a product is selected to start a cook cycle the blowers and heat come back on If set to NO the blowers are on constantly Fryer Type SP 19 Press gt button and SP 19 FRYER TYPE flashes in the left display Press the 4 or W buttons to choose GAS or ELEC Vat Type SP 20 Press gt button and SP 20 VAT TYPE flashes in the left display Press the A or W buttons to choose SPLIT or FULL 909 H 6 1 SPECIAL PROGRAM 909 as Y PENNY Coke Foodserelor MODE Continued Model EEE 141 142 143 144 Autolift Enabled SP 21 Press gt button and SP 21 AUTOLIFT ENABLED flashes in the left display Press the or W buttons to choose YES LIFT or NO LIFT If fryer is fitted with the auto lift option SP 21 must be set to YES LIFT otherwise set SP 21 to NO LIFT Bulk Oil Supply SP 22 Press gt button and SP 22 BULK OIL SUPPLY flashes in the left display Press the A or W buttons to choose YES SUPL or NO SUPL Set to
48. on the drain knob If Bulk Oil Dispose is set to YES V PUMP X DONE shows in the display Press X button Display shows MANUAL FILL POT followed by IS POT FILLED along with YES NO Fill the vat to the lower indicator line on the rear of the vat and then press y button See Filling or Adding Oil instructions from Section 3 3 Fryer returns to normal operation Remove the discard shuttle from under fryer and replace with the filter pan assembly 3 16 PENNY Coba Foodservior Solutions 3 14 OPERATING INSTRUC l TIONS FOR OPTIONAL BULK OIL DISPOSAL SYSTEM i W O IG Fa Figure 2 10 11 3 17 Model EEE 141 142 143 144 Connect the female quick disconnect that is attached to the hose in the rear of the open fryer to the correct male quick disconnect at the wall Once attached the hose can remain connected unless the open fryer is moved Figures 1 amp 2 BULK OIL DISPOSE in the Special Program Mode or Set Up Mode must to set to YES for the Bulk Oil Dispose System to operate Also a password code step 1 2 3 can be added in Special Programming SP 27 Press and hold left or right for split vats until display shows FILTER MENU along with 1 EXPRESS FILTER Press and release j gt button twice until display shows 3 DISPOSE Press V button and display shows DISPOSE YES NO or enter code 1 2 3 if SP
49. one 1s heard when an error code is displayed and to silence this tone press any button DISPLAY CAUSE CORRECTION E F Control board overheating E 5 Oil Turn switch to OFF position then turn switch back to ON overheating if display shows E 5 the heating circuits and temperature probes should be checked E 6A Temperature Turn switch to OFF position then turn switch back to ON probe open if display shows E 6A the temperature probe should be if display shows E 6B the temperature probe should be checked E 6B Temperature probe shorted checked E 10 High limit Reset the high limit by using a small screwdriver or Allen wrench gently pushing it into the hole in the heating element hinge if high limit does not reset high limit may need be replaced ae m E 157 Drain switch Make sure drain knob is completely pushed in 1f E 15 persists have drain switch checked E 18 A Leftlevel sensor open Turn switch to OFF position then turn switch back to ON Turn switch to OFF position then turn switch back to ON if display shows E 4 the control board is getting too hot check the louvers on each side of the unit for obstructions Turn switch to OFF position then turn switch back to ON E 18 B Rightlevel sensor open if display still indicates a failed sensor have the connectors checked E 18 C Both level sensors open at the control board hav
50. ould be the ID for nuggets Use the product buttons or the amp and W buttons to change the ID Alarms 1 amp 2 11 Press gt button until ALRM 1 shows in the left display and an alarm time in the right display Press the product buttons or the and W buttons to set an alarm Ex If a Cook Cycle was set at 3 minutes and an alarm was to go off after 30 seconds into the Cook Cycle 2 30 would be set in the display at this time When the timer counts down to 2 30 the alarm sounds After the alarm time is set press b gt button and ALRM 2 shows in the display and a second alarm can be programmed Quality Timer hold time 12 Press gt button until QUAL TMR shows in the display along with the preset holding time Press the product buttons orthe and W buttons to adjust holding time up to 59 59 Global Filter Tracking Include in Filter Count 13a Press gt button until INCL IN FLTR CNT flashes in the display along with YES or NO Using 4 amp and W buttons change the display to YES if that product s Cook Cycles are to be counted as part of the recommended filter process Set to NO if it is not to be included 309 H 5 1 MODIFYING PRODUCT 309 e R Y PENNY filobal Foodserelor SETTINGS Continued Model EEE 141 142 143 144 Mixed Filter Tracking Filter After X Number of Loads 13b Press gt button until FILTER AFTER flashe
51. p at 1 800 417 8405 or 1 937 456 8405 1108 Y PENNY Coba Foodservior San 1 4 SAFETY 1108 Model EEE 141 142 143 144 The Henny Penny open fryer has many safety features incorporated However the only way to ensure a safe operation is to fully under stand the proper installation operation and maintenance proce dures The instructions in this manual have been prepared to aid you in learning the proper procedures Where information is of particu lar importance or safety related the words DANGER WARNING CAUTION and NOTICE are used Their usage is described below SAFETY ALERT SYMBOLS are used with DANGER WARNING or CAUTION which indicates a personal injury type hazard NOTICE is used to highlight especially important information CAUTION used without the safety alert symbol indicates a potentially hazardous situation which if not avoided may result in property damage CAUTION used with the safety alert symbol indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury WARNING indicates a potentially hazardous situation which if not avoided could result in death or serious injury DANGER INDICATES AN IMMINENTLY HAZARDOUS SITUATION WHICH IF NOT AVOIDED WILL RESULT IN DEATH OR SERIOUS INJURY 1 2 H Y PENNY Model EEE 141 142 143 144 Coba Foodservior Solutions 1 4 SAFETY Continued Y Equipotential Ground Symbol 2007 ef
52. per rinsing after cleaning the vat e Drain valve clogged with crumbs e Drain trough clogged e Filter line connections loose e Filter paper or pad clogged e Filter not reassembled correctly e Filter pan not completely engaged e Filter pan clogged e Damaged O ring on filter line receiver on fryer e Power cord for vat 1 is not plugged in e Open circuit e the thermal reset button on the rear of the pump motor is tripped e Drain and clean oil e Use recommended oil Refer to filtering procedures Clean and rinse vat and then dry thoroughly Open valve force cleaning brush through drain Remove right side panel and remove plug from end of trough and clean trough e Tighten all filter line connections e Change filter paper or pad Refer to assembly instructions on inside of door Make sure filter pan return line is pushed completely into the receiver on the fryer Clean pan and change paper or pad Change O ring e Plug power cord into receptacle e Check circuit breakers behind left door beside control circuit breakers reset if needed e Allow time for the motor to cool and then using a screwdriver press hard against the button until it clicks i 7 PENNY Model EEE 141 142 143 144 Coba Foodservior San 7 2 ERROR CODES In the event of a control system failure the digital display shows an error message The message codes are shown in the DISPLAY column below A constant t
53. pped with an equipotential lug for this purpose The equipotential lug is marked with the following symbo Y 2 3 Y PENNY fiobal Foodserelor 2 6 ELECTRICAL REQUIREMENTS Continued CABLE RESTRAINT 4 i Pe d MUL init ie ratty i ENEA aA Py E q A I bolt is to be secured to the building using acceptable building construc tion practices DRYWALL CONSTRUCTION Secure l bolt to a building stud Do not attach to drywall only Preferred installation is approximately six inches to either side of service Cable restraint must be at least six inches shorter than flexible conduit 2 4 Model EEE 141 142 143 144 An all pole separate disconnect switch with proper capacity fuses or breakers must be installed at a convenient location between the fryer and the power source and must be installed according to national and local codes It should be an insulated copper conductor rated for 600 volts and 90 C For runs longer than 50 feet 15 24 m use the next larger wire size CE units require a minimum wire size of 6 mm to be wired to the terminal block It is recommended that a 30 mA rated protective device such as a residual current circuit breaker RCCB or ground fault circuit interrupter GFCI be used on the fryer circuit Permanently connected electric fryers with casters must be installed with flexible conduit and a cable restraint when installed in
54. product cooked PRODUCT FRY L1 Time of day the last Cook Cycle was started STARTED FEB 4 2 25P When Cook Cycle was stopped Early QUIT AT 0 10 REM 4 2 oe HENNY PENNY Model EEE 141 142 143 144 4 1 INFORMATION MODE 3 DAILY STATS Operational info of fryer for last 7 days DETAILS Continued Press gt and 3 DAILY STATS show in displays Press W button to start viewing the cook data Press the night DM view data for other days of week FUNCTION DISPLAY EX Day this data was recorded for APR 30 TUE Number of Hours Minutes the fryer was on L R ON HRS TUE 3 45 Number of times filtered L R FILTERED TUE Number of times filter skipped L R SKIPPED TUE 4 Number of times oil added L R ADD OIL TUE 4 Number of times oil discarded L R DISPOSE TUE 0 Oil temperature recovery time L R RECOVERY TUE 1 45 Total number of cook cycles that da L R TOT CK TUE 38 Number of cycles stopped before DONE Cook Cycles for Product 1 Cook Cycles for Product 2 Cook Cycles for Product 3 Cook Cycles for Product 4 Cook Cycles for Product 5 TUE COOK 5 Cook Cycles for Product 6 TUE COOK 6 Cook Cycles for Product 7 TUE COOK 7 Cook Cycles for Product 8 TUE COOK 8 Cook Cycles for Product 9 TUE COOK 9 Cook Cycles for Product 0 TUE COOK 0 Ol Wy oO 4 3 309 H Y PENNY Model EEE 141 142 143 144 fiobal Foodserelor 4 1 INFORMATION MODE 4 OIL STATS info of current oil
55. r W buttons to choose YES or NO If YES is chosen the user can exit the Express Filter fill operation 1009 as H Y PENNY loka Foodserelor 6 2 CLOCK SET 6 3 DATA LOGGING HEAT CONTROL TECH STAT AND FILTER CONTROL MODES 609 Model EEE 141 142 143 144 Press and hold the button for 5 seconds until LEVEL 2 followed by SP PROG and ENTER CODE show in the display Press the button again and CLK SET and ENTER CODE flash in the left display Enter code 1 2 3 first 3 product buttons CS 1 ENTER DATE MM DD YY flashes in the left display Use the product buttons to set the date in the right display Press gt button and CS 2 ENTER TIME flashes in the left display and the time flashes in the right display Press the A or W or use product buttons to change the time Press gt button and CS 2 ENTER TIME flashes in the left display and AM or PM flashes in the right display Use the A or W buttons to choose AM or PM Press gt button and CS 3 TIME FORMAT flashes in the left display and 12 HR or 24 HR shows in the right display Use the AX or W buttons to choose a 12 hour time format or a 24 hour time format Press gt button and CS 4 DAYLIGHT SAVING TIME flashes in the left display Use the A or V buttons to choose daylight saving time for your area 1 OFF 2 US 2007 amp aft
56. right vat Press and release gt button 6 times and display shows 7 CLEAN OUT Press V button and display shows OIL RMVD YES NO If oil has already been removed press V button and control skips down to Solution Added step 109 H as Y PENNY loka Foodservice Solutions CLEAN OUT MODE 3 17 909 Continued 10 Model EEE 141 142 143 144 If vat still has oil press X button and display shows DISPOSE YES NO Press V button to dispose of the oil or press X button to exit Clean Out Mode Display shows IS DISPOSAL UNIT IN PLACE YES NO If NO is selected display shows INSERT DISPOSAL UNIT Once disposal unit is in place press V button for YES open drain and display shows DRAINING and oil drains from vat Display then shows VAT EMTY YES NO Press V button when ready and close drain Bulk Oil Systems Only Display shows CHK PAN if the filter drain pan is missing Once pan is in place display shows OPEN DRAIN Pull out drain knob and display shows DRAINING and oil drains from vat Display then shows PUMP X DONE Press V button display shows DISPOSING and oil is pumped from drain pan Once pan is empty press X button twice and close drain Display shows SOLUTION ADDED YES NO Fill the vat to 1 in 25 mm above the top fill line with hot water and add 4 ozs 0 12 liters of ope
57. s section To ensure proper operation of fryer please consult Henny Penny Corp before changing any of these settings For more information on these functions contact Technical Support at 1 800 417 8405 or 1 937 456 8405 1 E LOG error code log Press and buttons at the same time and INFO MODE shows in the display followed by 1 E LOG NOC Press and lto exit Information Mode at any time Press W and A date amp time NOW show in displays This is the present date and time Press W and if a error was recorded B date time and error code information shows in display This is the latest error code that the controls recorded Press Wand the next latest error code information can be seen Up to 10 error codes B to K can be stored in the E LOG section 309 H aa Y PENNY codernice Soluiioni Coba Produ Model EEE 141 142 143 144 4 1 INFORMATION MODE 2 LAST LOAD Information on recent cook cycles 109 DETAILS Continued Press gt and 2 LAST LOAD show in displays Press a timer button o or for the product you want to view the cook data and the LED flashes Press Wbutton to start viewing the cook data For example if the left o LED is flashing PRODUCT FRY L1 show in displays If the right LED is flashing PRODUCT FRY R showin displays Press W button to start viewing the cook data FUNCTION DISPLAY EX Product Last
58. s in the left display along and the number of cook cycles between filters shows in the right display Press the product buttons or the and W buttons to change this value of 0 to 99 loads This needs set for each product gt Load Compensation Load Compensation Reference Full Heat PC Factor lt 14 15 16 17 Press gt button until LD COMP shows in the display along with the load compensation value This automatically adjusts the time to account for the size and temperature of the cooking load Press the product buttons or the A and W buttons to change this value of 0 to 20 Press gt button until LCMP REF shows in the display along with the load compensation average temperature if load compensation is set to OFF then __ _ shows in display and setting cannot be programmed This is the average cooking temperature for each product The timer speeds up at temperatures above this setting and slows down at temperatures below this setting Press the product button or the and ww buttons to change this value Press gt button until FULL HT shows in the display along with the full heat value in seconds which means the heat 1s on as soon as a timer button is pressed for the programmed length of time Press the product buttons or the A and ww buttons to change this value of 0 to 90 seconds Press b gt button until PC FACTR shows in the display along with the proportional
59. s the 4 amp or W oruse product buttons to set the idle temperature 200 to 375 F 93 to 191 C 909 ae H Y PENNY loka Foodservior Solutions 6 1 SPECIAL PROGRAM MODE Continued No Cook Cycle Product Cycles Count Fish 2 1 2 French Fries 8 1 8 Chicken 4 1 4 309 Model EEE 141 142 143 144 Filter Tracking Mode SP 8 Filter Tracking signals the operator when the oil needs filtering by counting the number Cook Cycles between filters Press gt button and SP 8 and FILTER TRACKING MODE show in the display Use the A ad V buttons to choose either 1 MIXED filter tracking or 2 GLOBAL GLOBAL means all the products have the same number of cook cycles between filters MIXED means each product may be set with different number of cook cycles between filters The controls adds the cycle counts see example at left and when the counts equal 1 or greater filtering is suggested Ex load of fish 2 loads of french fries a load of chicken equals 1 1 2 1 8 1 8 1 4 1 MIXED If MIXED 1s selected press gt button and SP 8A and SUGGEST FILTER AT shows in the left display and a value between 75 and 100 shows on the right display Press the and W buttons to change this value The lower the value the sooner the control recommends to filter Ex If set to 75 the control suggest filtering after 3 4 of the programmed cook cycles is met whereas at 100 all t
60. ssing twice during normal operation One volume setting shows in the left display NONE to 10 10 being the loudest and the second volume shows in the right display To select the volume press the V button under the desired volume SETUP COMPLETE The Setup Mode can also be accessed by re initializing the controls in Special Program Mode in Level 2 programming SP 3 909 PENNY Coba Foodservior Solutions 3 3 FILLING OR ADDING OIL Figure 3 1009 Model EEE 141 142 143 144 The oil level must always be above the heating elements when the fryer is heating and at the oil level indicators on the rear of the vat Failure to follow these instructions could result in a fire and or damage to the fryer Solid oil is not recommended Solid oil could cause clogging and pump failures 1 Itisrecommended that a high quality liquid frying oil be used in the open fryer Some low grade oils have a high moisture content which causes foaming and boiling over BURN RISK Wear gloves to avoid severe burns when pouring hot oil into vat Oil and all metal parts that are in contact with the oil are extremely hot take care to avoid splashing 2 Oil Capacities Full size vats 15 quarts 30 Ibs 14 2 liters 13 6 kg Split vats 7 5 quarts 15 Ibs 7 1 liters 6 8 kg All vats have 2 level indicator lines inscribed on the rear wall of the vat in which the upper most line shows the oil at the proper level w
61. tarting the next cook cycle Number of Baskets SP 14 Press gt button and SP 14 NUMBER OF BASKETS flashes in the left display Press the or W buttons to choose 2 or 4 baskets per well Cooking Indicator SP 15 Press gt button and SP 15 SHOW COOKING INDICATOR flashes in the left display Press the 4 or W buttons to choose YES and during a cook cycle shows which timer is counting down Choose NO and will not show during acook cycle 909 6 6 Sa Y PENNY codernice Soluiioni Coba Produ H 6 1 SPECIAL PROGRAM MODE Continued Model EEE 141 142 143 144 2nd Language SP 16 Press gt button and SP 16 2ND LANGUAGE flashes on the left display Press the A or VW buttons to select the desired 2nd language By setting a 2nd language in the controls 2 languages can now be chosen by pressing Fputton during normal operation One language shows in the left display and the second language shows in the right display Pressing the V button selects the language in the displays 2nd Volume SP 17 Press gt button and SP 17 2ND VOLUME flashes on the left display Press the 4 amp 4 or W buttons or the product buttons to select the desired 2nd volume By setting a 2nd volume in the controls 2 volumes can now be chosen by pressing button twice during normal operation One volume setting shows in the left display NONE to 10 10 being the loudest and the second v
62. the United States See illustration at left Holes are available in the rear fryer frame for securing the cable restraint to the fryer The cable restraint does not prevent the fryer from tipping Each vat has it s own power cord assembly and uses NEMA 15 50 Straight Plug or NEMA 15 60P The supply power cords shall be oil resistant sheathed flexible cable no lighter than ordinary polychloroprene or other equivalent synthetic elastomer sheathed cord 109 Y PENNY Coba Foodservior San 2 7 DIMENSIONS Auto Lift Fryers Front to rear dimension is 36 7 8 93 66 cm For doorways 36 in 91 44 cm or less the protective bumper bar on rear of the fryer needs removed See photo at below iW a f s ll i 510 16 1 4 in 412 mm 45 34 in 1102 mm Model EEE 141 142 143 144 ae MS in 818 mm in 74 mm 31 2 5 Model EEE 141 142 143 144 SECTION 3 OPERATION 3 1 OPERATING COMPONENTS Refer to explanations on the next pages A lt a 12 13 14 Figure 3 1 17 Figure 3 2 Figure 3 3 Figure 3 4 Bulk Oil Supply Fryers Only 3 1 110 3 1 OPERATING COMPONENTS Continued Fig Item No No 3 1 1 3 1 2 3 1 3 3 1 4 3 1 5 3 1 6 3 1 7 3 1 8 3 1 9 110 xP Coba Foodservior San ENNY Description DY s CF Digital Display K 2 Model EEE 141 142 143 144
63. the display shows STOPPED and the SmartFilter is cancelled The blue light goes out and the controls return to normal operation The controls will suggest filtering after several more cook cycles If display shows VAT EMTY followed by YES NO that means the drain is clogged Use the straight white brush to clear drain and then press y button Display shows DRAINING and then controls proceed with the filtering process Once the control has completed the filtering process display shows CLOSE DRAIN Push in on the drain knob to close the drain Figure 3 The vat then re fills with oil Once vat is filled display shows IS POT FILLED YES NO Make sure vat is full and then press V button for YES and the control returns to normal operation 1009 Y PENNY Coke Foodserelor Model EEE 141 142 143 144 3 11 SMARTFILTER EXPRESS 7 Ifthe oil has not pumped back to the proper level in the vat Continued 209 during the SmartFilter Express process press X button for NO and pump runs for another 30 seconds Display shows IS POT FILLED YES NO Make sure vat is full and then press V button and display shows and the control returns to normal operation Press X button and pump runs for another 30 seconds You can try to fill the vat 3 times Filter Error 10 After trying to fill the vat 3 times without success the controls 11 then shows CHANGE FILT
64. tilation system This is essential to permit efficient removal of steam exhaust and frying odors Special precaution must be taken in designing an exhaust canopy to avoid interference with the operation of the fryer We recommend you consult a local ventilation or ne company to help in designing an adequate system Ventilation must conform to local state and national codes Consult your local fire department or building authorities Check the data plate mounted on the inside of the doors to determine the correct power supply SHOCK HAZARD This fryer must be adequately and safely grounded earthed or electrical shock could result Refer to local electrical codes for correct grounding earthing proce dures or in absence of local codes with The National Electrical Code ANSI NFPA No 70 the current edi tion In Canada all electrical connections are to be made in accordance with CSA C22 1 Canadian Electri cal Code Part 1 and or local codes To avoid electrical shock this appliance must be equipped with an external circuit breaker which will disconnect all ungrounded unearthed conductors The main power switch on this appliance does not disconnect all line conductors FOR EQUIPMENT WITH CE MARK ONLY To prevent electric shock hazard this appliance must be bonded to other appliances or touchable metal surfaces in close proximity to this appliance with an equipotential bonding conductor This appliance is equi
65. uct buttons to adjust the tone of the speaker 2000 being the maximum value and 50 the minimum Liquid or Solid Cooking Oil Used SP 6 Press gt button until SP 6 MELT CYCLE SELECT scrolls in the left display Unless solid oil is being used in the vats the right display should show 1 LIQUID If solid oil is used the unit MUST BE equipped to handle solid oil Use the 4 amp amp and W buttons to change the right display to 2 SOLID Idle Mode Enabled SP 7 An Idle Mode allows the oil temperature to drop to a lower tem perature when notin use This savies on oil and utilities Press gt button and SP 7 and IDLE MODE ENABLED flash in the left display Press the M or W buttons to choose YES or NO With YES in the display press j gt button and SP 7A and USE 0 FOR IDLE flash on the left display Press the or W buttons to select YES or NO If YES is selected an Idle Mode can be programmed in product buon Press button and SP 7B and AUTOIDLE MINUTES flash in the left display Press the M or W oruse product buttons to set the time 0 to 60 minutes fryer stays idle before the auto idle is enabled Ex 30 means if product is not cooked in that vat for 30 minutes the control automatically cools the oil down to the idle setpoint temperature Press gt button and SP 7C and IDLE SETPT flash in the left display Pres

Download Pdf Manuals

Related Search

Related Contents

閲覧はこちらから（PDF/8.32MB）  Z31055A Z31055B - Lidl Service Website  Bedienungsanleitung  SoftWall Finishing Systems SW643087010 Instructions / Assembly  User Manual - Comkit Online  User Manual - Oculum  LALD Series User Manual  Samsung SL-M2070F Uporabniški priročnik  

Copyright © All rights reserved. Failed to retrieve file