Heath Zenith P6036 User's Manual
Contents
1. Incorrect circuit wiring if this is a new installation Re aim the sensor to cover desired area Light Control may be installed in a relatively dark location Light Control is in Test Set control switch to an ON TIME position Light Control may be sensing small animals or automobile traffic re aim sensor Range is set too high Reduce Range Lights stay on continuously Lights flash on and off POSSIBLE CAUSE 1 A lamp is positioned too close to the sen sor or pointed at nearby objects that cause heat to trigger the sensor Reposition the lamp away from the sensor or nearby objects Light Control is pointed toward a heat source like an air vent dryer vent or brightly painted heat reflective surface Reposition sensor Light Control is in Manual Mode Switch to Auto Heatorlightfrom the lamps may be turning the Light Control on and off Reposition the lamps away from the sensor Heat being reflected from other objects may be affecting the sensor Reposition sen sor Light Control is in the Test mode and warming up Flashing is normal under these conditions Light Control is detecting a light source Reposition Light Control or lamp 598 1280 002. PROGRESS TEST foerat Put the ON TIME switch on the ON TIME LIGHTING bottom of the sensor in the TEST og position 1051 TEST Replacement AUTO Motion Sensor Put the ON TIME switch inthe 1 ON TIME 5 or 10 minute position kK gt Model P6036 aa Features MANUAL MODE Turns on lighting when motion is detected Automatically turns lighting off Photocell keeps the lighting off during daylight hours LED indicates motion was sensed day or night Requirements The Light Control requires 120 volts AC If you want to use Manual Mode the control must be wired through a switch Some codes require installation by a qualified electrician OPERATION On Time Works Day Night 5 Seconds x x Auto 1 5 or 10 Min X Manual To Dawn xX resets to Auto Mode at dawn Note When firstturned on wait about 1 t 2 minutes for the circuitry to calibrate Manual mode only works at night because daylight returns the sen sor to AUTO E 1 Second OFF then Flip the light switch off for one second then back on to toggle between AUTO and MANUAL MODE Manual mode works only with the a ON TIME switch in the 1 5 or 10 position back on Mode Switching Summary Move ON TIME Switch to 1 5 or 10 minutes Flip light switch off for one second then back on MANUAL MODE If you get confused while switching modes turn t
3. he power off for one minute then back on After the calibration time the control will be inthe AUTO mode 598 1280 00 INSTALLATION O After screwing the sensor into the wall plate connect the junction box wires to the Light For under eave installation the sensor head Control wires by twisting together and securing must be rotated as shown in the next two steps with wire connectors for proper operation and to avoid the risk of elec trical shock Red Sensor Wire to For eave mount only White to White Black Lamp Wire Junction Box YN YQ A ON Lamp Holders O Swing the sensor head towards the clamp SCIOW Controls Clamp Screw Rotate the sensor head clockwise 180 so Black to Black the controls face down Controls Optional Connect additional load A across the white and red wires Total LA lighting load including lampheads on L7 gt fixture must not exceed 500W 4 2A J PL yw Controls Mount THE LIGHT O Followthe instructions that came with your light fix ture for mounting and adjusting the light fixture O Keep regular PAR 38 lamps at least 1 25 mm from the sensor Halogen lamps should be kept at least 2 51 mm from the sensor If the sensor pops out of the ball joint loosen the clamp screw and push the sensor back into the ball joint Tighten the clamp screw when done These instructions show the sensor wired to flood lamps T
4. he white sensor wire is neutral The black sensor wire is hot The red wire is the switched hot wire The lighting load 500 W 4 2A max is placed across the white and red wires WIRE THE LIGHT CONTROL A WARNING Turn power off at the fuse or circuit breaker O Remove the existing light fixture if present D 598 1280 00 TEST AND ADJUSTMENT O Turn on the circuit breaker and light switch NOTE Sensor has a 1 1 2 minute calibration period before it will detect motion When first turned on wait 1 2 minutes O Turn the RANGE control to the mid position and the ON TIME control to the TEST position ON TIME o o o a RANGE 10 5 1 TEST MIN MAX Bottom of Sensor Avoid aiming the control at e Objects that change temperature rapidly such as heating vents and air conditioners These heat sources could cause false triggering Areas where pets or traffic may trigger the control Nearby large light colored objects reflecting light may trigger the shut off feature Do not point other lights at the sensor 8 ft 180 2 4m 70 ft 21m Maximum Range Maximum Coverage Angle The sensoris less sensitive to motion directly towards it most sensitive to motion across its field of view Least Sensitive Most Sensitive 598 1280 00 Sensor O Loosen the clamp screw Clamp inthe sensor ball joint and lt H Screw gently rotate the sensor CD Walk thro
5. ugh the cover Ball age area noting where Joint you are when the lights turn on also the LED will flash several times when motion is detected Move the sensor head up down Aim Sensor or sideways to change the Down for Short coverage area Keep the Coverage sensor atleast1 2 5 cm away from the lamps O Adjust the RANGE as needed RANGE set too high may increase false Aim Sensor triggering Higher for Long O Secure the sensor head Coverage by tightening the clamp screw Do not overtighten the screw O Setthe amount of TIME you wantthe lights to stay on after motion is detected 1 5 or 10 minutes Warning Risk of fire Do not aim the lamps at a combustible surface within 3 ft 1 m SPECIFICATIONS Range Up to 70 ft 21 m varies with surrounding temperature Sensing Angle Up to 180 Electrical Load Upto500Watt 4 2A Maximum Incandescent Up to 250 Watt maximum each lamp holder Power Requirements 120 VAC 60 Hz Operating Modes TEST AUTO and MANUAL MODE Time Delay 1 5 10 minutes Range Adjustable SYMPTOM Lights will not come on Lights come on in daylight Lights come on for no apparent reason TROUBLESHOOTING GUIDE POSSIBLE CAUSE Light switch is turned off Light is loose or burned out Fuseis blown or circuit breaker is turned off Daylight turn off is in effect recheck after dark
Download Pdf Manuals
Related Search