Havis-Shields KWIK-STRIKE 4000 Series User's Manual
Contents
1. Havis Shields EQUIPMENT CORPORATION INSTALLATION INSTRUCTIONS KWIK STRIKE 4000 SERIES SCENE LIGHT Warning Please read all instructions and warnings prior to installation Power must be disconnected prior to installation or servicing This luminaire must be installed and operated per NFPA 70 National Electric Code and all applicable codes and regulations These instructions are provided as a guideline for proper installation HARDWARE amp COMPONENTS Qty 4 1 Description Part 10 X 54 Phillips Flat Head Sheet Metal Screw GSM34151 Mounting Gasket KRM000023 INSTALLATION 1 Mounting e Determine the best location to mount the fixture Optimum installation height is between seven and nine feet above ground level Caution Before cutting or drilling holes ensure that the mounting surfaces are clear of obstructions and that the screws will not damage internal parts of the vehicle e Use the supplied template to cut a suitable 9 17 32 x 5 3 4 mounting hole in the location where the fixture is intended to be installed e Drill suitable mounting holes for the appropriate mounting hardware The supplied template may be used or the fixture itself may be set in place and used as a template e Attach the mounting gasket to the flange on the fixture Caution Failure to install the gasket may permit water entry into the vehicle e Install the fixture in the mounting hole and secure it with suitable mounting screw2. _4 08 doc
3. s The mounting screws supplied are intended for use in sheet metal of at least 1 8 thickness It is recommended to wax the screws prior to installation Caution Ensure that the fixture is secure and the gasket is tightly compressed to prevent water from entering the vehicle Havis Shields does not warrant that the mounting hardware or gasket supplied are suitable for all installations suitability for an installation is the sole responsibility of the installer e Connect the wires as directed below and test for correct operation 2 Wiring e All wiring must be connected per applicable codes e Connect wires following the appropriate diagram on next page e Test the light for proper operation For 120 volt AC Fixtures All 120 volt AC fixtures have three 3 wires The green wire is always ground Attach the black wire to 120 volt HOT and the white to 120 volt NEUTRAL Black Hot White Neutral Green Ground For 12 VDC Fixtures All versions have a red and black wire or a white and black wire Attach the red white wire to positive 12 VDC and the black wire to negative Red 12VDC meo sd 3 Maintenance Caution Do not touch the bulb glass or fixture reflector If necessary clean with isopropyl alcohol Make sure power is off before performing any maintenance on the fixture Loosen the lens frame screws and remove the lens frame To replace a halogen bulb remove the bulb by unscrewing i
4. t from the socket Replace the bulb with a similar type 250W maximum Clean the lens and gasket area before re assembling the fixture Re assemble the fixture ensuring the lens frame screws are tightened to 15 18 in lb torque Test for proper operation 4 Troubleshooting Consolidator Kwik Raze Collins Dynamics Kwik Kit PrisonerTransports K 9 Transports 75 Jacksonville Box 2099 Warminster PA 18974 800 524 9900 215 957 0720 P 215 957 0729 F In the event of improper operation for halogen fixtures first check the bulb and replace it if it is burned out If the halogen bulb is okay or for an HID fixture use a voltmeter to ensure that the fixture is receiving adequate power Halogen fixtures require 120vAC and HID fixtures require 12VDC for proper operation Correct any faults found If necessary contact Havis Shields for additional troubleshooting procedures www Havis com KR 4000_INST_4 08 doc 8 9 X CTE 6C 6 NMOHS SV SATOH X CTE LI 6 SIAL LAO LAO AOA AHL ASN OL SI LI SASVO TIV NI LI ONISN AALNINd SI LI TUNSNA OL ALWIdNAL AHL TAASVAN 7 AZIS 001 DNITVOS ON HLIM GALNIdd SI ALWIdNaAL AHL TAASNA 1 Add V NOW ALWIdIWAL SHL SNILNINd JI ALON ALWIdIWAL ONIINOQOW SARs 10007 AMNIALS MIMM KR 4000_INST
Download Pdf Manuals
Related Search