Harman Kardon PM635I User's Manual
Contents
1.2. ce BI KO oa i sah Compact Disc Player TV Tuner Connecting Other Components Carefully connect the plugs to the left and right channel jacks Push the plugs in all the way Poor setting of the plugs tends to cause hum or intermittent sound and may damage the speakers NOTE While you are connecting this unit to the rest of your high fidelity system please unplug the power cord discon necting not only this unit but all the components from the AC outlet Do not interwind the connection wires with the power cord If interwound the sound quality may be degraded AC Convenience Receptacles This unit is provided with two AC convenience receptacles on the rear panel for supplying power to a tuner turntable tape deck or other low power component The receptacles have a power capacity of 180 watts each Check the component s owner s manual to find its power requirement SWITCHED The power to this receptacle is turned on and off by this unit s power switch UNSWITCHED The power to this receptacle is independent of this unit s power switch NOTE In some countries these AC convenience receptacles are not available Video Component or ef To wall OIL outlet so gt Open Real Tape Right channel Left channel Deck Speaker System 2 Connecting Speakers Connect the speaker wires carefully to the speaker terminals on the rear panel so as not to mi
3. quence sortie 1W 0 3dB Facteur d amortissement Rapport signal bruit r f puissance de sortie nominale A WTD Phono MM Tuner CD Vid o Sensibilit imp dance d entr e Phono MM Tuner CD Vid o Surcharge phono MM Caract ristiques des commandes de tonalit Rel vement Coupure des graves 50Hz Rel vement Coupure des aigus 10kHz Dimensions L x H x P Poids Alimentation Mod le courant Pour le Canade Consommation Mod le courant Pour le Canada SOW par canal distorsion harmonique totale inf rieure 0 09 sur 8Q 48W par canal distorsion harmonique totale inf rieure 1 sur 4Q 15A lt 10Hz to 100kHz 0 5Hz 150kHz 60dB 80dB 98dB 2 2mV 47KkQ 125pF 135mV 22kQ 110mV 410dB 10dB 10dB 10dB 443 x 103 x 353 mm 17 1 2 x 4 x 13 15 16 po 6 4kg 14 1 livres Secteur 220 240V 50 60Hz Secteur 120V 60Hz 190W 220W 242VA Toutes les sp cifications et caract ristiques peuvent tre modifi es sans pr avis POUR LES CLIENTS CANADIENS li convient de bien tenir compte de ce qui suit tant donn que la prise secteur est une prise polaris e ATTENTION POUR PREVENIR LES CHOCS ELECTRI QUES NE PAS UTILISER CETTE FICHE POLARISEE AVEC UN PROLONGATEUR UNE PRISE DE COURANT O UNE AUTRE SORTIE DE COURANT SAUF SI LES LAMES PEUVENT ETRE INSEREES A FOND SANS EN DECOUVERT LAISSER AUCUNE PARTIE A
4. connected to the TAPE 2 jacks for recording dubbing will begin NOTE You can listen to a program source selected via the FUNCTION selector while dubbing is taken place To monitor the sound being recorded use the headphones connected to the phones jack of tape deck Tape Playback 1 Turn the VOLUME control knob to the minimum level and press the POWER switch The POWER indicator lights up 2 Set the SPEAKERS selector for the desired speaker system s 3 Set the TAPE MONITOR selector to the tape 1 or tape 2 position corresponding to the tape deck to be played 4 Insert a recorded tape in the tape deck and set the tape deck in the playback mode 5 Advance the VOLUME control knob to a comfortable level and adjust the BASS and TREBLE control knobs as desired 6 Activate the BALANCE control knob or LOUDNESS switch if necessary TROUBLESHOOTING CHECKLIST checklist Also check other related components such as the tuner turntable speakers and other electrical equipment you use with this amplifier Most of the problems consumers have with their high fidelity system are due to incorrect operation If this unit does not operate as you intended first check the items in the following Problem The POWER indicator does not light up when the POWER switch is pressed Cause Remedy The power cord is not plugged in The POWER indicator lights up but no sound is heard The TAPE MONITOR sel
5. reproduction and therefore has no negative effect on sound quality FEATURES GENERAL INSTRUCTIONS Always Use the Correct AC Voltage Always connect the power cord to a domestic mains outlet Never connect the unit to an outlet supplying a higher voltage This may create a fire hazard NOTE FOR CUSTOMERS OTHER THAN CANADA This unit is supplied with a voltage selector enabling selection between 220V and 240V on the rear panel If the selector is not set to the local voltage set the selector to the correct voltage with a screwdriver before connecting the power cord to a mains outlet Handle the Power Cord Gently Do not disconnect the plug from the AC outlet by pulling the cord always pull the plug itself Pulling the cord may break the wire lf your unit will be left unused for any considerable length of time disconnect the plug from the AC outlet Do not place furniture or other heavy objects on the cord and avoid dropping heavy objects on it Also do not make a knot in the power cord Not only may the cord be damaged it can also cause a short circuit and a consequent fire hazard Place of Installation Place your unit on a firm and level surface Avoid installing your unit under the following conditions gt Moist or humid places D Places exposed to direct sunlight or close to heating equipment gt Extremely cold locations such as those in the direct draft from an air conditioner gt Places subject to excessive
6. vibration or dust b Poorly ventilated places Do not cover the ventilation slots on the top of the unit This will cause the temperature inside the unit to rise which can eventuaily affect the reliability of your unit Moving the Unit Before moving the unit be sure to unplug the power cord from the AC outlet and disconnect the interconnection cords to other units Do Not Open the Cabinet To prevent fire or shock hazard do not tamper with internal components for inspection or maintenance Harman Kardon does not guarantee against performance degradation resulting from any modification If water a hairpin or wire accidentally enters the unit imme diately unplug the power cord from the AC outlet to prevent shock and consult an authorized Harman Kardon service sta tion If you use the unit under this condition it may cause a fire or shock hazard Cleaning When the unit gets dirty wipe it with a soft dry cloth If ne cessary wipe it with a soft cloth dampened with mild soapy water and then wipe with a dry cloth Never use benzine thinner alcohol or other volatile agents and avoid spraying an insecticide near the unit CONNECTIONS Turntable MM OUTPUT aS ML vor Cassette Tape Deck Speaker System 1 Right channe Left channel O 0 lol lemme TE HE TE 11 5 500 o
7. x 13 15 16 Weight 6 4kg 14 11bs Power Supply General model Canada model AC 220V 240V 50 60Hz AC 120V 60Hz Power Consumption General model 190W Canada model 220W 242VA All specifications and features subject to change without notice SPECIFICATIONS FOR CUSTOMERS IN THE UK Your unit is supplied with the flex which will have either two or three wires so the following items should be observed to guarantee safety THREE CORE FLEX WARNING THIS APPARATUS MUST BE EARTHED IMPORTANT The wires in this mains lead are coloured in ac cordance with the following code Green and yellow Earth Blue Neutral Brown Live As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows The wire which is coloured green and yellow must be connected to the terminal in the plug which is marked by the letter E or by the safety earth symbol or coloured green or green and yellow The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black The wire which is coloured brown must be connected to the terminal which is marked with the fetter L or coloured red TWO CORE FLEX IMPORTANT The wires in this mains lead are coloured in ac cordance with the following code Blue Neutral Brown Live As the colours of the wires in the mains lead of thi
8. PPLIANCE TO RAIN OR MOISTURE EHCC High instantaneous Current Capability Recent studies have shown that while reproducing dynamic music signals the instantaneous impedances of nearly all oud speakers drop to less than one third of the nominal ratings These low instantaneous impedances typically require 3 to 6 imes more current than an 8 Ohm resistive load Reduced dynamic range and increased distortion will result if the am plifier cannot provide these higher currents For this reason he PM635i was designed to provide 15 amperes of instan aneous current BUltrawide Bandwidth The bandwidth of this unit is exceptionally wide and inde pendent of negative feedback This improves transient accuracy and phase linearity mLow Negative Feedback This unit has been designed to have low distortion and wide bandwidth without high negative feedback This further im proves its dynamic accuracy m Discrete Component Circuitry In order to achieve the above goals all discrete electronic circuitry has been employed All available integrated circuits could not provide this high level of performance E Sophisticated Electronic Protection Harman Kardon engineers developed a unique protection system that permits high instantaneous current to be driven into speaker systems but protects the amplifier from short circuited or damaged speakers and wires This protection system in no way limits amplifier output voltage or current during music
9. Stereo Integrated Amplifier Instruction Manual Manuel d utilisation Bedienungsanleitung Manuale di istruzioni Bruksanvisning Gebruiksaanwijzing harman kardon harman kardon PM635i VOLUME FUNCTION TREBLE pa HEADPHONES ge POWER T STEREO INTEGRATED AMPLIFIER Congratulations on your purchase of the Harman Kardon PM635i Stereo Integrated Amplifier In order to appreciate the full performance of this sophisticated unit please be sure to read this owner s manual and use your integrated amplifier only in ac cordance with its instructions Keep it in a safe place for future reference Continuous Average Power FTC both channels 30 Watts per channel driven 20 20 000Hz less than 0 09 THD into 8 Ohms DIN 1kHz 48 Watts per channel less than 1 THD into 4 Ohms HCC High instantaneous 15 Amps Current Capability Power Bandwidth at half rated output 8 Ohms lt 10Hz to 100 000Hz Frequency Response at 0 5Hz to 150 000Hz 1 Watt output 0 3dB Damping Factor 60dB Signal to Noise Ratio ref rated power output A wtd Phono MM 80dB Tuner CD Video 98dB Input Sensitivity Impedance Phono MM 2 2mV 47k Ohms 125pF Tuner CD Video 135mV 22k Ohms Phono Overload MM 110mV Tone Control Characteristics Bass Boost Cut at 50Hz 10dB 10dB Treble Boost Cut at 10kHz 10dB 10dB Dimensions W x H x D 443 x 103 x 353 mm 17 1 2 x 4
10. copy 1 to 2 Select this position to duplicate a tape in the tape deck connected to the TAPE 1 jacks onto the tape in the tape deck connected to the TAPE 2 jacks tape 1 Select this position to play a tape or to monitor during recording on the tape deck connected to the TAPE 1 jacks source Select this position to listen to a program source other than a tape tape 2 Select this position to play a tape or to monitor during recording on the tape deck connected to the TAPE 2 jacks FUNCTION SELECTOR FUNCTION This selector is used to select a program source other than a tape video Select this position to listen to the sound from a video component connected to the VIDEO jacks CD Select this position to listen to the sound from a compact disc player connected to the CD jacks tuner Select this position to listen to an FM or AM broadcast from the stereo tuner connected to the TUNER jacks phono Select this position to listen to a disc played on the turntable connected to the PHONO jacks VOLUME CONTROL KNOB VOLUME This knob controls the sound level Turning clockwise increases the sound volume and turning counterclockwise decreases it Set this knob at a minimum level before turning the power on or changing the sound source to protect the speakers from being damaged by a sudden high level sound LOUDNESS SWITCH loudness This switch is pressed to create a natural sound quality when listening at a low vol
11. ector is in the tape 1 or tape 2 position The FUNCTION selection was not made properly The SPEAKERS selector is in the off po sition The speaker wires are disconnected or broken Sound is not heard from the speaker system on one side The connection of speaker wires is incorrect or incomplete The connection wires to other equipment are disconnected The BALANCE control knob is turned to either the extreme right or left position When playing a turntable a low pitched noise hum or level while playing a turntable an undesirable prolonged sound howling is heard equipment are reversed The ground wire of the turntable is dis connected turntable Too much low frequency sound is present Plug in the power cord securely Set the TAPE MONITOR selector to the source position Set the FUNCTION selector to the proper position for the desired program source Set the SPEAKERS selector to the position of your desired speaker system s Check the speaker wires and connect them correctly Check the speaker wires for disconnection or breaking and reconnect them correctly Check the wires for disconnection and connect them correctly Set the mark on the BALANCE control knob to the center position When listening to stereo sound Theleftandright speaker wires are reversed Check the speaker wires and connect them the left and right sounds are correctly re
12. eo headphones with a standard 1 4 inch plug can be connected to this jack When the SPEAKERS selector is in the off position sound can still be obtained via the headphone jack SPEAKER SELECTOR SPEAKERS This selector is used to select the desired speaker system s off Select this position to listen to sound via the headphone with no sound from the speaker system s speakers 1 Select this position to actuate the speaker system connected to the SPEAKER SYSTEM 1 terminal speakers 2 Select this position to actuate the speaker system connected to the SPEAKER SYSTEM 2 terminal 1 2 Select this position to actuate simultaneously the two speaker systems connected to the SPEAKER SYSTEM 1 and 2 terminals respec tively BASS CONTROL KNOB BASS This knob controls the low frequency sound level Turn it clockwise to boost or counterclockwise to reduce the low frequency sound level TREBLE CONTROL KNOB TREBLE This knob controls the high frequency sound level Turn it clockwise to boost or counterclockwise to reduce the high frequency sound level BALANCE CONTROL KNOB BALANCE This knob is used to balance the left and the right channels Usually it is set at the center Turn it to the left or right to balance the sound if it seems unbalanced from the speakers or the headphones TAPE MONITOR SELECTOR TAPE MONITOR This selector is used when playing a tape deck or monitoring during recording
13. onents connected to the VIDEO jacks on a tape deck connected to the TAPE 1 and or TAPE 2 jacks 1 Turn the VOLUME control knob to the minimum level and press the POWER switch The POWER indicator lights up 2 Set the SPEAKERS selector for the desired speaker system s 3 Select the desired program source with the FUNCTION selector 4 Set the TAPE MONITOR selector to the source position 5 Advance the VOLUME control knob to a comfortable level 6 Start recording by activating the tape deck s connected to the TAPE 1 and or TAPE 2 jacks The source sound can be listened to from the speakers or headphone 7 To monitor the sound being recorded set the TAPE MONITOR selector to the tape 1 or tape 2 position according to the tape deck that you wish to monitor NOTE The record output signal is carried directly from the program source without being influenced by the volume ba lance bass and treble controls and loudness switch of this unit Tape Dubbing Two tape decks can be connected to this unit and dubbing can be done from the tape in the tape deck connected to the TAPE 1 jacks onto the tape in the tape deck connected to the TAPE 2 jacks 1 Turn the VOLUME contro knob to the minimum level and press the POWER switch The POWER indicator lights up 2 Set the TAPE MONITOR selector to the copy 1 to 2 position 3 After setting the tape deck connected to the TAPE 1 jacks for playback and the tape deck
14. s apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red FOR CUSTOMERS IN CANADA The AC plug is a polarized plug so the following item should be taken into consideration CAUTION ro PREVENT ELECTRIC SHOCK DO NOT USE THIS POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN AN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERV ICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbal within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS A
15. stake the left and the right channels or reverse the speaker polarities and Use sufficiently thick wire 18 gauge for short lengths 16 12 gauge for longer lengths It is recommended to use color coded wire for easy polarity identification Speaker wires should be as short as possible and the left and the right channel wires should be the same length 1 Remove about 20mm 3 4 inch of insulation from the end of each wire and twist the strands of each end 2 After making sure of the correct channel and polarity loosen the SPEAKER SYSTEM termina knob and insert the conductor directly into the recess at the upper right of the terminal Then tighten the terminal knob and the end of speaker wire is automatically wound around the terminal CAUTION Two speaker systems can be connected to this unit The minimum speaker impedance should be 4 Ohm when only one speaker system is connected When two speaker systems are connected care should be taken that net impe dance does not become less than 4 Ohm harman kardon PM635i SPEAKERS speakers 1 _ speakers 2 CONTROLS AND FUNCTIONS VOLUME TAPE MONITOR FUNCTION tuner POWER SWITCH POWER Pressing this switch will turn on the power and the POWER indicator lights up Press the switch again to turn the power off POWER INDICATOR When the POWER switch is pressed this indicator lights up in red HEADPHONE JACK HEADPHONES Ster
16. trol knobs as desired 7 Activate the BALANCE contro knob or LOUDNESS switch if necessary N oak Listening to a Compact Disc 1 Turn the VOLUME control knob to the minimum level and press the POWER switch The POWER indicator lights up 2 Set the SPEAKERS selector for the desired speaker system s Set the FUNCTION selector to the CD position Set the TAPE MONITOR selector to the source position 5 Activate the compact disc player and set the player in the play mode 6 Advance the VOLUME control knob to a comfortable level and adjust the BASS and TREBLE control knobs as desired 7 Activate the BALANCE contro knob or LOUDNESS switch if necessary Era Listening to the Video Aux Input Source To listen to a video component TV tuner or other auxiliary component 1 Turn the VOLUME control knob to the minimum level and press the POWER switch The POWER indicator lights up 2 Set the SPEAKERS selector for the desired speaker system s Set the FUNCTION selector to the video position Set the TAPE MONITOR selector to the source position Activate the component connected to the VIDEO jacks Advance the VOLUME control knob to a comfortable level and adjust the BASS and TREBLE contro knobs as desired 7 Activate the BALANCE control knob or LOUDNESS switch if necessary Tape Recording Recording from a program source FM AM broadcast turn table or compact disc player or comp
17. ume by boosting the low and high fre quency ranges OPERATIONS Listening to a Record Disc 1 Turn the VOLUME control knob to the minimum level and press the POWER switch The POWER indicator lights up 2 Set the SPEAKERS selector for the desired speaker system s 3 Set the FUNCTION selector to the phono position 4 Set the TAPE MONITOR selector to the source position 5 Activate your turntable and place the stylus on the record disc 6 Turn the VOLUME control knob clockwise to increase the sound volume to the desired level 7 Adjust the BASS and TREBLE control knobs to obtain the desired tone 8 Activate the BALANCE control knob or LOUDNESS switch if necessary NOTE If you hear a hum at average listening levels turn the POWER switch off and check to see that the phono and the ground connections are secure Depending on the cartridge type used less hum may be created without the ground connection Listening to Radio Broadcasts 1 Turn the VOLUME control knob to the minimum level and press the POWER switch The POWER indicator lights up Set the SPEAKERS selector for the desired speaker system s Set the FUNCTION selector to the tuner position Set the TAPE MONITOR selector to the source position Activate the tuner and tune to broadcast frequency When the desired station is selected advance the VOLUME control knob to a comfortable level and adjust the BASS and TREBLE con
18. versed The left and right wires connected to other Check the wires to other equipment and connect them correctly Make the ground wire connection correctly buzz is heard e The connections of the turntable wires are Insert the turntable wires into the PHONO incorrect or incomplete jacks of this unit securely When increasing the volume e Howling is created by the speakers and Place the speakers further away from the turntable Place the turntable on a more solid surface Decrease the setting of the BASS control knob Turn off the LOUDNESS switch Sound quality is poor Input components have not been set up correctly Tone control is not proper Check the antenna of the tuner cartridge of the turntable or head of the tape deck etc and make corrections as needed Adjust the BASS and or TREBLE control knobs to obtain the desired tone SPECIFICATIONS Nous vous f licitons d avoir choisi Famplificateur int gr st r o Harman Kardon PM635i Afin d obtenir de cet appareil sophistiqu un ren dement optimal veuillez lire ce mode d emploi atten tivement et utiliser votre amplificateur conform ment aux directives Conservez soigneusement le mode d emploi pour toute r f rence ult rieure Puissance moyenne continue FTC 20Hz 20kHz par canal DIN 1kHz Haute capacit en courant instantan HCC Bande passante 50 de la puissance sur 8Q R ponse en fr
Download Pdf Manuals
Related Search