Harbor Freight Tools Windmill Mole Chaser Product manual
Contents
1. after all 3 blades are stacked a r Self tapping Screws 5 Bolts 9 Extension Tube A Blades 3 Stacked blade assembly Maintenance 1 The Bearing Assembly 4 is not grease packed it will require lubricating periodically 2 Check the pole stability periodically If it seems loose remove the Windmill and pound in the pole Replace the Windmill 3 Keep the Blades 3 clean of dirt and debris SKU 47987 Page 4 REV 11 04 01 07 02 07 Parts List and Assembly Drawing Part No Description Qt Bot Bolt PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER NOR DISTRIBU TOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO NOTE Some parts are listed and shown for illustration purposes only and are not available indi vidually as replacement parts SKU 472. 987 Page 5 REV 01 07 02 07
3. MOLE CHASER WINDMILL Model 47987 ASSEMBLY and OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd Camarillo CA 93011 Visit our Web site at http www harborfreight com Copyright 2002 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools For technical questions and replacement parts please call 1 800 444 3353 Specifications Overall Dimensions 19 1 2 L x 18 1 2 W Blade Dimensions 18 Lx 2 1 2 W 2 51bs Save This Manual You will need the manual for the safety warnings and precautions assembly instructions operating and maintenance procedures parts list and diagram Keep your invoice with this manual Write the invoice number on the inside of the front cover Keep the manual and invoice in a safe and dry place for future reference Safety Warnings and Precautions WARNING When using tools and this product basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment Read all instructions before using this tool ibe Keep work area clean Cluttered areas invite injuries Observe work area conditions Keep work area well lighted Keep children away Children must never be allowed in the work area Do not let them handle Windmill Use the right product for the job There are certain applications for
4. ad warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs If there is any doubt do not assemble the tool 13 Maintenance For your safety maintenance should be performed regularly by a qualified technician 14 Location Choose a safe location away from power lines to install the Windmill Caution If setting up the Windmill on a roof surface extreme care must be taken when working on a sloped slippery roof surface this type of work on a roof should only be done by an experienced worker who is capable of handling the physical de mands of this type of job 15 Extreme Weather Conditions Be aware that the Windmill is not designed to withstand extreme weather conditions the product may break or fail under extreme weather conditions resulting in property damage and or personal injury Locate the product in an area that is clear of passing people or animal traffic Warning The warnings cautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur It must be under stood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator Unpacking When unpacking check to make sure the parts listed on page 5 are included If any parts are missing or broken please call Harbor Freight Tools at the number on the cover of this manual as soon as possibl
5. e SKU 47987 Page 3 Assembly and Operation Refer to FIGURE 1 below and the Assembly Drawing on page 5 Warning Before setting this Windmill in the ground contact your local utility company to make sure there are no buried cables or pipes in the desired location If locating the Windmill on a rooftop read and adhere to the warnings on page 3 1 Stack the Blades 3 so that they resemble the pattern in the box in FIGURE 1 making sure the fins face out toward the wind Lay number 2 over number 1 so that the holes match Then lay number 3 over number 2 so that all four holes match evenly 2 Lubricate the Bearing Assembly 4 prior to assembly using a lightweight grease 3 Using three Bolts 8 and three star Washers 10 attach the blade assembly to the Bearing Assembly 4 and secure with three Nuts 6 4 Attach the Directional Finder 2 to the Tube Frame 1 with two Self tapping Screws 5 Thread in the Bolt 9 to secure the Bearing Assembly 4 See Figure 1 5 Tap Extension Tube B into the ground Make sure it is securely in place and insert Extension Tube A onto Tube B Operation Notes 1 A rattling sound in the tube is normal 2 Justa few turns in a 24 hour period will effectively rid the area of moles 3 Keep the unit lubricated See Maintenance section below FIGURE 1 Directional Bolts Star washers 8 10 Bearing 4 Finder 2 ii 3 Tube Frame 1 H E eS Close up of matched holes
6. which this Windmill was designed Do not modify this Windmill and do not use this Windmill for a purpose for which it was not intended Dress properly Do not wear loose clothing or jewelry as they can be caught in moving parts Protective electrically nonconductive clothes and nonskid footwear are recommended when working Wear restrictive hair covering to contain long hair Use eye protection Always wear ANSI approved impact safety goggles during assembly Do not overreach Keep proper footing and balance at all times Maintain tools with care Keep Windmill clean for better and safer performance Follow instructions for lubricating Stay alert Watch what you are doing use common sense Do not assemble the Windmill when you are tired Check for damaged parts Before using Windmill any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function Check for alignment and binding of moving parts any broken parts or mounting fixtures and any other condition that may affect proper operation Any part that is damaged should be properly repaired or replaced by a qualified technician SKU 47987 Page 2 11 Replacement parts and accessories When servicing use only identical replacement parts Use of any other parts will void the warranty Only use accessories intended for use with this tool 12 Do not assemble Windmill if under the influence of alcohol or drugs Re
Download Pdf Manuals
Related Search