Harbor Freight Tools Steering Wheel Remover Set Product manual
Contents
1. then store them in the case in a clean dry location Page 3 Parts List and Assembly Diagram Part Description Qty Part Description OQty Cap Screw 3 1 2 L 5 16 24 TPI 9 16 x 18 TPI internal Cap Screw 3 1 2 L M8 x 1 25 4 Steering Wheel Bolt 2 8 Carrying Case 4 L 5 16 18 TPI 9 ForcingScrew Cd Snap Ring Bolt M14 x 1 5 Lock Plate Attachment d Record Serial Number Here Note Some parts are listed and shown for illustration purposes only and are not Note If product has no serial number available individually as replacement parts record month and year of purchase instead PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS DOCUMENT AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO PITTSBURGH 3491 Mission Oaks Blvd PO Box 602. 09 Camarillo CA 93011 800 444 3353
3. PITTSBURGH EEE Steering Wheel Removal Set Specifications 3 1 2 L 3 8 16 TPI Cap Screws 3 4 2 L 5 16 24 TPI Item 68982 2 each 3 1 2 L M8 x 1 25 Steering Wheel 4 L 5 16 18 TPI INSTRUCTIONS amp PRECAUTIONS _ Bolts 2 Snap Ring Bolts M14 x 1 5 1 a 9 16 x 18 TPI TUTTO nduded Molded Molded Carrying Case Case IMPORTANT SAFETY INFORMATION To prevent serious injury from explosion carefully follow service instructions to AWARNING disable airbag before use 2 Assemble and use only according to Read this material before these instructions Improper assembly using this product and usage can create hazards Failure to do so can result 3 Wear ANSI approved safety goggles in serious injury and heavy duty work gloves during use SAVE THIS MANUAL Visit our website at http www harborfreight com Use as intended only Use only according to vehicle When unpacking make sure that the service instructions product is intact and undamaged 6 Inspect before use If any parts are missing or broken do not use if damaged please call 1 800 444 3353 Keep away from children as soon as possible Disconnect ground lead from vehicle battery before using Steering Wheel Remover Copyright 2011 by Harbor Freight Tools All rights reserved No portion of this document or any artwork contained herein may be 9 Do not use when tired or when under reproduced
4. in any shape or form without the the influence of drugs or medication express written consent of Harbor Freight Tools mE Diagrams within this document may not be drawn 0 Maintain product labels and proportionally Due to continuing improvements nameplates These carry actual product may differ slightly from the important safety information product described herein Tools required for If unreadable or missing contact assembly and service may not be included Harbor Freight Tools for a replacement For technical questions or replacement parts please call 1 800 444 3353 Operation Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document before set up or use of this product AWARNING TO PREVENT SERIOUS INJURY FROM EXPLOSION Carefully follow service instructions to disable airbag before working near steering wheel or steering column Steering Wheel Removal The Steering Wheel Remover is designed to remove the steering wheels of most domestic and imported vehicles Three separate Cap Screw 1 2 and 3 sets and one set of Steering Wheel Bolts 4 are used with the Forcing Screw 9 The following instructions apply to most standard vehicles however consult your vehicle owner s manual for specific instructions for your vehicle To Remove a Steering Wheel 7 Place the Forcing Screw 9 1 Set the vehicle transmission to park over the center of the wheel neutral if vehicle is a man
5. ment 10 then the Washer 7 over the Jack Bolt Thread the Nut 11 onto the Jack Bolt and turn clockwise using a wrench sold separately to hold down the lock plate and allow the snap ring to be removed Remove the Jack Bolt To Install Snap Ring and Lock Plate 1 Position the lock plate over the steering shaft Select the appropriate Jack Bolt 5 or 6 for your vehicle and slide the snap ring onto it Thread the Jack Bolt onto the steering shaft then place the Lock Plate Attachment 10 then the Washer 7 over the Jack Bolt Thread the Nut 11 onto the Jack Bolt and turn clockwise using a wrench sold separately until the snap ring can be slipped down over the beveled end of the center post screw and into the shaft s groove Remove the Jack Bolt Note The Steering Wheel Lock Plate Attachment can also be used to access the turn signal switch and airbag modules on certain GM vehicles Consult your vehicle manufacturer for instructions for your vehicle WARNING Reenable airbag system after service according to service instructions Maintenance 1 SKU 68982 Before each use inspect the general condition of the tool Check for cracked or broken parts and any other condition that may affect its safe operation If damaged have corrected before further use Do not use damaged equipment 2 For technical questions please call 1 800 444 3353 Coat all parts with a light oil to prevent rust
6. ual 8 Slide the Cap Screws through transmission point the wheels each end of the Forcing Screw straight ahead turn the engine off bar and thread them into the and set the emergency brake threaded holes in the wheel 2 Disconnect the ground 9 Using a wrench sold separately lead from the battery slowly turn the center bolt clockwise 3 Carefully remove any molding horn forcing the steering wheel off the shaft or air bag assembly following your vehicle manufacturer s instructions until you can access the shaft nut holding the steering wheel hub assembly and the steering shaft 4 Draw a line with a marker Forcing sold separately at the 12 o clock Screw 9 position on the shaft and the steering wheel so you can align the steering wheel when reinstalling it 5 Remove the shaft nut with a wrench sold separately Screws 6 Locate the threaded holes in the steering wheel hub assembly and select the Cap Screw 1 2 or 3 set that fits the threads Page 2 For technical questions please call 1 800 444 3353 SKU 68982 Snap Ring Removal The Lock Plate Attachment is used to compress the steering wheel lock plate while the snap ring is removed installed To Remove Snap Ring and Lock Plate 1 Remove the Steering Wheel following the previous instructions for this kit Select the appropriate Jack Bolt 5 or 6 for your vehicle and thread onto the steering shaft until secure Place the Lock Plate Attach
Download Pdf Manuals
Related Search