Home

Harbor Freight Tools NiMH/NiCd Battery Quick Charger Product manual

image

Contents

1. 3 Do not open housing Do not charge NiCd or NiMH batteries 16 Maintain labels and nameplates at the same time These carry important information If unreadable or missing contact 6 Do not charge damaged batteries Harbor Freight Tools for a replacement Follow all manual instructions 17 The warnings precautions and Always wear ANSI approved safety instructions discussed in this instruction goggles during use manual cannot cover all possible conditions and situations that may Page 2 For technical questions please call 1 888 866 5797 Item 47618 occur It must be understood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator SAVE THESE INSTRUCTIONS Power Cord Safety 1 A short power supply cord is to be provided to reduce risks resulting from becoming entangled in or tripping over a longer cord 2 Longer extension cords are available and may be used if care is exercised in their use Follow all directions when using a long extension cord 3 If along extension cord is used a the marked electrical rating of the detachable power supply cord or extension cord should be at least as great as the electrical rating of the appliance 5 b if the appliance is of the grounded type the extension cord should be a grounding type 3 wire cord and c the longer cord should be arranged so that it wil
2. please call 1 888 866 5797 manual control You must observe the charging time Periodically check the condition of the charger and batteries Do not over charge the batteries The green light will stay on until you remove the 9V batteries from the Battery Compartment Note Unplug and then re plug the Battery Charger each time you recharge the empty batteries to reset the charger Page 3 Record Product s Serial Number Here Note If product has no serial number record month and year of purchase instead Note Replacement parts are not available for this product TROUBLESHOOTING The Charge Indicator Light s do 1 Make sure the Power Cord Plug of the Battery Charger is not illuminate when battery ies are plugged into a working 120 Volt grounded electrical outlet inserted 2 Disconnect the Power Cord Plug from its electrical outlet Check to make sure each battery is inserted properly into the Battery Compartment The Battery Charger and or the This is normal and should not be cause for concern batteries feel warm to the touch LIMITED 90 DAY WARRANTY Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase This warranty does not apply to damage due directly or indirectly to misuse ab
3. Owner s Manual amp Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions assembly operating inspection maintenance and cleaning procedures Write the product s serial number in the back of the manual near the assembly diagram or month and year of purchase if product has no number Keep this manual and the receipt in a safe and dry place for future reference Ca HUNDERBOLT Battery Quick Charger ITEM 47618 4 56 te q JI 2s i amp gt WwW 35 w Visit our website at http www harborfreight com REV 14i Email our technical support at productsupport harborfreight com When unpacking make sure that the product is intact and undamaged If any parts are missing or broken please call 1 888 866 5797 as soon as possible Copyright 2008 by Harbor Freight Tools All rights reserved R gt No portion of this manual or any artwork contained herein may be reproduced in Read this material before using this product any shape or form without the express written consent of Harbor Freight Tools Failure to do so can result in serious injury Diagrams within this manual may not be drawn proportionally Due to continuing SAVE THIS MANUAL improvements actual product may differ slightly from the product described herein Tools required for assembly and service may not be included PRODUCT SPECIFICATIONS Charging Capacity D C AA amp AAA Charge up to FOUR each 9
4. V Charge up to TWO each UL LISTED Charging Time NiCd Cells AAA AA C D 5 Hours E183799 NiCd 9V 110 mAh 10 Hours NiMH Cells AAA AA C 8 Hours NiMH D Cells 16 Hours NiMH 9V 150 160 mAh 15 Hours This battery s charge time needs to be monitored manually This battery needs more than one cycle to fully charge HOUSEHOLD USE ONLY 2 Do notcover the vents of the Battery Charger place on a hard surface 10 Keep this Battery Charger out of the l M PO RTANT reach of children SAFEGUARDS 11 ee Charger from outlet when READ AND UNDERSTAND ALL 12 Do not operate this Battery Charger with a damaged cord or plug or after any INSTRUCTIONS malfunctions Do not use if it has been i 3 damaged in any manner When using electrical appliances basic 9 y safety precautions should always be 13 Do not use outdoors followed including the following 14 Do not use this Battery Charger for 1 CAUTION Risk of shock Dry location other than intended use use only 15 WARNING The cord of this product 2 Charge ONLY NiCd or NiMH type contains lead and or di 2 ethylhexyl rechargeable batteries Other types of phthalate DEHP chemicals known to batteries may burst causing injury and the State of California to cause cancer or property damage and birth defects or other reproductive harm Wash hands after handling California Health amp Safety Code 4 Do not overcharge batteries 25249 5 et seq
5. l not drape over the counter top or tabletop where it can be pulled on by children or tripped over OPERATION i Slide the Battery Type Switch to select the correct type of battery For Nickel Cadmium batteries set the Battery Type Switch to the NiCd position For Nickel Metal Hydride batteries set the Battery Type Switch to the NiMH position See illustration Plug the Charger into a correct household electric outlet The LED CH 1 CH 2 CH 3 or CH 4 will glow red color to indicate the proper charging After the proper charge time is reached 5 hours for NiCd and 8 hours for NiMH except for 9V of both types and NiMH D Cells the red lights will turn off and the trickle charge is on The charged batteries are now ready for use See illustration Unplug the Battery Charger and remove all batteries when not in use Note When 9V batteries are placed in the Charger the green light at the top of the Charger will come on After 10 Hours for NiCd 110 mAh and 15 hours for NiMH 150 160 mAh remove the 9V batteries from the Charger The 9V batteries are now ready for use Note The charging of 9V batteries is by 1 Place the Battery Charger on a flat smooth dry surface near an electrical outlet 2 Insert 1 to 4 D C AA AAA batteries or 1 to 2 9V batteries in the Battery Compartment DO NOT MIX NiCd NICKEL CADMIUM AND NiMH NICKEL METAL HYDRIDE BATTERIES Item 47618 For technical questions
6. use negligence or accidents repairs or alterations outside our facilities criminal activity improper installation normal wear and tear or to lack of maintenance We shall in no event be liable for death injuries to persons or property or for incidental contingent special or consequential damages arising from the use of our product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS To take advantage of this warranty the product or part must be returned to us with transportation charges prepaid Proof of purchase date and an explanation of the complaint must accompany the merchandise If our inspection verifies the defect we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement We will return repaired products at our expense but if we determine there is no defect or that the defect resulted from causes not within the scope of our warranty then you must bear the cost of returning the product This warranty gives you specific legal rights and you may also have other rights which vary from state to state 3491 Mission Oaks Blvd PO Box 6009 Camarillo CA 93011 1 888 866 5797

Download Pdf Manuals

image

Related Search

Related Contents

  to user manual.  Measurement Studio Release Notes  SPX2000—Bedienungsanleitung    VDO Dayton MS 3100 - CONRAD Produktinfo.  SMART_MX_04_L_SAT_RECEIVER - Ver. 01  Otterbox Commuter  

Copyright © All rights reserved.
Failed to retrieve file