Harbor Freight Tools Long_Life Wireless LED Puck Light Product manual
Contents
1. Operation 1 Position the Puck Light by pressing on the left or right side of the Lens to direct the light left or right 30 degrees 2 Turn the Puck Light base 360 degrees to direct the light 3 Press in on the center of the Lens once to turn the light on at full brightness 4 Press again for lower brightness 5 Press a third time to turn the light off Troubleshooting No light when 1 Batteries weak or 1 Replace batteries Lens pushed in dead 2 Installed batteries 2 Reinstall batteries incorrectly paying attention to polarity One LED does LED burned out Replace Puck Light or not light have a qualified technician repair the unit Maintenance 1 Remove the batteries before storing the Puck Light Immediately remove the batteries when the batteries have run down Store the Puck Light in a clean and dry location when not in use gt ww DN There are no customer replaceable parts on this unit PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THat ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CE2. WIRELESS FIVE LED PUCK LIGHT ONE PUCK LIGHT THREE PUCK LIGHTS ASSEMBLY AND OPERATING INSTRUCTIONS Due to continuing improvements actual product may differ slightly from the product described herein Distributed Exclusively by 3491 Mission Oaks Blvd Camarillo CA 93011 Visit our Web site at http www harborfreight com Copyright 2006 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools For technical questions and replacement parts please call 1 800 444 3353 Specifications ltem Description Battery Requirement 3 AAA 1 1 2 volt batteries per Puck Light not included Run Time Up to 60 hours using new high quality batteries Bright white S O Bright white Lens Head Swivels 360 degrees pivots 30 degrees left right Weight 0 5 Ibs each puck Save This Manual You will need the manual for the safety warnings and precautions assembly instructions operating and maintenance procedures parts list and diagram Keep your invoice with this manual Write the invoice number on the inside of the front cover Keep the manual and invoice in a safe and dry place for future reference Safety Warnings and Precautions WARNING When using this product basic safety precautions should always be followed to reduce the risk of personal injury and damage
3. to equipment Read all instructions before using this tool 1 The Puck Light does not provide enough light to illuminate a pathway for walking 2 Use only the size and battery type specified Do not mix different types of batteries together alkaline and NiCad 3 Use care when installing batteries Placing the batteries in the wrong direction polarities reversed may damage the Puck Light 4 When batteries are used up recycle them properly Do not throw into the trash or burn them Note Performance of this product may vary depending on variations in battery power Warning The warnings cautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur It must be understood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator Unpacking When unpacking check to make sure that the product is complete and undamaged If any parts are missing or broken please call Harbor Freight Tools at the number on the cover of this manual SKU 94253 94254 For technical questions please call 1 800 444 3353 Page 2 Installation Mounting with Hook and Loop Tape 1 Find the Hook and Loop tape supplied They come attached to each other Pull apart the Hook and Loop sections Peel the backing off the Hook pad Center on the Battery Cover and press down to adhere Clean the spot whe
4. RTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO SKU 94253 94254 For technical questions please call 1 800 444 3353 Page 4
5. re the Light is to be located of any dirt and grease Peelthe backing of the Loop pad and press down and adhere Light to the location After the Batteries not included are installed press the Puck Light against the Loop pad to secure Mounting with Screw 1 Caution Avoid electrical shock Be certain that you are not drilling or screwing into any electrical wires Remove the Back Cover by carefully pulling up on Tabs Remove the bag of Screws included located inside the Puck Light Locate the mounting location and make a pencil Tabs mark at the center point If mounting to a wall use appropriate screw lugs not included for the screws provided If mounting onto other material drilling may be required located behind the wall 4 5 Screw in mounting Screw leaving a 1 16 inch space under the screw head Place the Screw into the center hole of the Back Cover slide the Back Cover to the smaller portion of the hole and tighten Screw completely After the Batteries not included are installed press the Puck Light onto the Back Cover to secure It should snap into place Installing Batteries 1 3 Remove the Back Cover by carefully pulling up on the Tabs Install three new AAA 1 1 2 volt batteries into each Puck Light Align the polarity on the Battery with the on the battery holder Snap in the Back Cover SKU 94253 94254 For technical questions please call 1 800 444 3353 Page 3
Download Pdf Manuals
Related Search