Harbor Freight Tools Knockout Punch Kit 10 Pc Product manual
Contents
1. HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO NOTE Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts REV 09 06 ITEM 912012. Metal Punch Kit Safety Precautions and Instructions Distributed Exclusively by p HARBOR FREIGHT aim is TOOLS wa TO PREVENT SERIOUS INJURY READ AND UNDERSTAND ALL WARNINGS AND INSTRUCTIONS BEFORE USE 3491 Mission Oaks Blvd Camarillo CA 93011 Copyright 2004 by Harbor Freight Tools All rights reserved No portion of this instruction sheet or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools For technical questions please call 1 800 444 3353 1 2 6 T SAVE THIS INSTRUCTION SHEET Operation Instructions on Back This kit has sharp edges that can cut and injure you e Keep fingers away from the blade especially during use e Keep this kit away from children e Do not hold the workpiece while using this kit on it The blade may suddenly break through causing personal injury Flying pieces debris smoke or dust caused during use can injure you e Always wear ANSI approved safety goggles full face shield and dust mask respirator during use If this set is used on fiberglass or similar materials additional protective equipment such as a disposable painter s jumpsuit should also be used e Use this kit only on the following recommended materials Mild Steel 10 gauge thick or less Fiberglass less than 08 about g 4 thick Aluminum 15 gauge thick or less Plastic less than 08 about 9 64 thick
3. Use on other materials may result in chipping breakage personal injury and damage to this kit the workpiece and or the tool that this kit is used with Do not attempt to force this kit to do the cutting work of a larger one There are certain applications for which this kit was designed Do not modify this kit and do not use this kit for a purpose for which it was not intended Pieces of the tool can break off and cause injury to the eyes injury to the face or other injury e Before every use check for any broken parts or mounting fixtures and any other condition that may affect proper operation Any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function e Do not use if any blade is worn cracked or chipped e Keep this set clean and in a dry location to prevent rust prolong the life of the tool and help prevent breakage Replacement parts and accessories When servicing use only identical replacement parts Use of any other parts is dangerous and will void the warranty Only use accessories intended for use with this kit Do not use this kit if under the influence of alcohol or drugs Read warning labels if taking prescription medicine to determine if your judgment or reflexes are impaired while taking drugs If there is any doubt do not use this tool Stay alert Watch what you are doing use common sense Do not use this kit if you are tired Read and ad
4. here to all safety warnings and precautions in the manual for any tool used with this Kit The warnings cautions and instructions discussed in this instruction sheet cannot cover all possible conditions and situations that may occur It must be understood by the operator that common sense and caution are factors which cannot be built into this set but must be supplied by the operator Operation Instructions Using a drill drill a pilot hole through the center of the location that you want the larger hole to be Note Pilot hole should be 1 2 diameter for Part Number 1 bolt and 3 4 diameter for Part Number 2 bolt Place the 1 2 Die 4 over the Small Drive Bolt 1 with the flat side against the bearing Insert the Small Drive Bolt through the hole The punches are very sharp Always keep hands and fingers away from the blades On some materials it may be helpful to apply light oil to the Punch to help it move freely If this is done caution must be exercised to avoid being cut by the blade Thread the 1 2 Punch 3 onto the Bolt on the other side of the material with the blade side facing the material to be cut Finger tighten until the Punch is snug against the material positioning is similar to Figure A right except with the smaller hardware Use a wrench ratchet or drill not included to turn the Drive Bolt driving the Punch into the material Risk of electric shock or death Before drilling pilot
5. holes or using this kit ensure that the area of the material the kit is used on is free from any wires cables and utility lines Figure A Using Large Hardware A WAAAY MM iii Similar to Figure A Use caution so that once the Punch breaks through the tool doesn t slip and injure you Carefully unthread the Punch to remove the material If a larger hole is desired after the hole is opened up using the smaller Punch and Die the above steps can be repeated using the Large Drive Screw 2 with a larger Punch and Die pair to get the desired size After use clean the Punch Die and Bolt by oiling them lightly and carefully wiping them with a dry cloth Store them in the case in a dry cool area out of children s Parts List i Siar Bie Bot 6 Dk Yo Punch 8 1 Die aire 9 fe eh reach PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR
Download Pdf Manuals
Related Search