Harbor Freight Tools Gear Puller Set 14 Pc Product manual
Contents
1. every use do not express written consent of Harbor Freight use if parts are loose or damaged Tools Diagrams within this document may not be drawn proportionally Due to continuing 8 Maintain product labels and improvements actual product may differ slightly nameplates These carry important from the product described herein Tools required safety information If unreadable for assembly and service may not be included or missing contact Harbor Freight For technical questions or replacement Tools for a replacement parts please call 1 800 444 3353 Manual Revised 11c Operation Instructions Read the ENTIRE IMPORTANT A SAFETY INFORMATION section at the beginning of this document including all text under subheadings therein before set up or use of this product Pulling Gears 14b Washers 16 Push Rod 9 7 Powis ae Push Rod 10 Nut I 15b Washers 16 Figure 1 1 Page 2 Thread the Push Rod 9 into the Bracket 6 Place a Washer 16 a Nut 14b or 15b and a Washer 16 onto the Pawls 14a amp 15a Slide each Pawl into a slot on the Bracket as shown above so one Washer is below the Bracket and the Nut and other Washer are above the Bracket Slide the Cone Head Insert 10 into the end of the Push Rod 9 Slide the Pawls together until they fit snuggly against the Bracket 6 For technical questions please call 1 800 444 3353 gear to be pulled then tigh2. PITTSBURGH Specifications 14 PC Gear Puller Set S Pulls Gears 9 32 IN to 3 IN Range Gear Puller Spread to 5 3 4 IN Gear Pulling Bearing Pulling amp Separating Timing Gear Pulling Steering Wheel Pulling Sprocket Pulling Pulley Pulling 5 16 IN 18 3 8 IN 16 3 8 IN 24 8 x 1 25 mm INSTRUCTIONS amp PRECAUTIONS He OC a case not shown Applications Sprocket and Pulley Tapped Hole Capacity Construction Center Bolt is hardened Steel Visit our website at http www harborfreight com AWARNING Read this material before Important Safety Information Precautions using this product Failure to do so can result 1 Assemble and use only according to in serious injury these instructions Improper assembly SAVE THIS MANUAL and usage can create hazards 2 Wear ANSI approved safety goggles and heavy duty work gloves When unpacking make sure that the during assembly and usage product is intact and undamaged Keep area clean and well lit If any parts are missing or broken please call 1 800 444 3353 4 Keep children and other as soon as possible bystanders out of the area 5 Do not use when tired or when under Copyright 2011 by Harbor Freight Tools the influence of drugs or medication All rights reserved No portion of this document 6 Use as intended only or any artwork contained herein may be reproduced in any shape or form without the 7 Inspect before
3. event rust then store them in Push Rod 9 is recommended the case in a clean dry location for difficult pulling jobs 5 Position the Bearing Separators 2 amp 3 around the base of the Bearing to be separated Tighten each nut evenly 7 Using an adjustable wrench sold separately tighten the Push Rod 9 against the center shaft of the bearing to separate the bearings from one another REV 11c SKU 30305 For technical questions please call 1 800 444 3353 Page 3 Parts List and Assembly Diagram Part Description _ Qty Part _ Description _ Qty Flat Head for Push Rod Bearing Separator 3 8 x 16T Connecting Bolt 3 8 x 24T Bearing Separator 3 8 x 16T step down thread 5 16 x 18 Bolt for Separator 1 2 x 12T Connecting Bolt 3 8 x 24T Bolt for Separator 1 2 x 12T step down thread 5 16 x 18 6 Bracket _ __ 1 Pawi 3 8 x 16T zi 7 Connecting Bolt 3 8 x 16T 14b Nut O step down thread M8 x 1 25 15a Pawl 3 8 x 16T 1 Connecting Bolt 3 8 x 16T 15b Nut y tC step down thread M8 x 1 25 16 FlatWasher 4 9 PushRod _ J1 Lube Oil Bottle not shown Cone Head for Push Rod Note This kit includes two extra Connecting Bolts 12 amp 13 for use with other bearings or gears These parts do not fit the Bearing Separators 2 amp 3 in this Gear Pulling Set Record Serial Number Here Note If product has no serial number record month and year of purchase
4. instead Note Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS DOCUMENT AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO S Page 4 For technical questions please call 1 800 444 3353 SKU 30305
5. ten the Nuts on both Pawls Screw the Push Rod 9 into the shaft at the center of the gear by turning the Head of the Push Rod with a wrench not included This will allow the gear to be pulled clear of its position Separating Ball Bearings Push Rod Connecting Bolts 9 ae Washer Flat Head Insert 11 A Separator Bolt 4 amp 5 Rud with Nut amp Washer Bearing Separators 2 amp 3 Figure 1 Thread the Push Rod 9 into the Bracket 6 then slide the Flat Head Insert 11 into the end of the Push Rod Lay the Bearing Separators 2 amp 3 so they face each other creating an open circle Remove the Nut and Washer from the Separator Bolts 4 amp 5 then slide the Bolts through REV 11c SKU 30305 the Bearing Separator holes and replace the Washers and Nuts Maintenance Note Do not tighten Bolts 4 Slide a Washer 16 onto the two 1 Before each use inspect the Connecting Bolts 7 amp 8 and then general condition of the tool Check slide them into the slots on the for cracked or broken parts and Bracket keeping the Washers any other condition that may affect above the Bracket Thread the its safe operation If damaged Bolt ends into the holes on the have corrected before further use top of the Bearing Separators 2 Do not use damaged equipment Note A light coat of oil on the shaft 3 Coat all parts with a light oil to near the bearing gear and on the pr
Download Pdf Manuals
Related Search