Harbor Freight Tools Foldable Saw Horse Set 2 Pc Product manual
Contents
1. Figure F 9 Install another Locking Brace and Bolt to the opposite pair of legs 10 Set the Sawhorse up on flat level ground Tighten any loose hardware This helps to ensure that the sawhorse will sit level 11 Repeat the entire assembly procedure with the other Sawhorse Item 61700 Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product AWARNING Inspect tool before use looking for damaged loose and missing parts If any problems are found do not use tool until repaired Before use double check that the Leg Locking Braces are securely attached to the bolts Set Up 1 Lay the Sawhorse on the ground Wooden Board 5 Carefully turn over the Sawhorse face down Pull the Legs out on each side 6 Repeat on second Sawhorse 2 Loosen both Locking Knobs 7 WARNING Confirm that the Leg Locking 3 Swing the Leg Locking Brace so that it catches Braces are securely attached to the Bolts on the exposed Bolt Repeat on other side and all hardware is tight before every use 4 Tighten both Locking Knobs Collapse 1 Loosen the Locking Knobs 3 Repeat on the opposite side 2 Lift up the hooked end of the Leg Locking Brace 4 Close the Sawhorse Legs and and allow the Leg Locking Brace to dangle retighten the Locking Knobs Maintenance Procedures not specifically explained in this ma2. IMPORTANT SAFETY INFORMATION Maximum Weight Capacity Assembly Precautions 1 Assemble only according to these instructions Improper assembly can create hazards Keep bystanders out of the area during assembly Do not assemble when tired or when under the 2 Wear ANSI approved safety goggles and influence of alcohol drugs or medication heavy duty work gloves during assembly Weight capacity and other product capabilities apply 3 Keep assembly area clean and well lit to properly and completely assembled product only Use Precautions 1 This product is not a toy Do not allow children to play with or near this item Do not exceed listed weight capacity 1 000 Ib weight capacity evenly distributed across two sawhorses Be aware of dynamic loading 2 Use on flat level hard surface able to support load Sudden load movement may briefly create 3 Wear ANSI approved safety goggles excess load causing product failure during assembly and use Maintain product labels and nameplates 4 Use as intended only Use at least These carry important safety information ET TO toe ar icad If unreadable or missing contact PP i Harbor Freight Tools for a replacement 2 4 slice wed tga sy eonenuse The warnings cautions and instructions discussed p gea in this instruction manual cannot cover all possible 6 Secure the workpiece to the sawhorses if possible conditions and situations that may occur It must Page 2 For te
3. Owner s Manual amp Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions assembly operating inspection maintenance and cleaning procedures Write the product s serial number in the back of the manual near the assembly diagram or month and year of purchase if product has no number Keep this manual and the receipt in a safe and dry place for future reference 2 MACHINERY 2 Piece Foldable SAWHORSE SET Visit our website at http www harborfreight com Email our technical support at productsupport harborfreight com ITEM 61700 When unpacking make sure that the product is intact and undamaged If any parts are missing or broken AWARNING please call 1 888 866 5797 as soon as possible Copyright 2013 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in Read this material before using this product any shape or form without the express written consent of Harbor Freight Tools Failure to do so can result in serious injury Diagrams within this manual may not be drawn proportionally Due to continuing SAVE THIS MANUAL improvements actual product may differ slightly from the product described herein Tools required for assembly and service may not be included Specifications per Sawhorse 32 x 5 1 2 x 1 1 2 Wood Top Dimensions 1000 Ib for each Sawhorse must be used in pairs
4. YER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO Record Serial Number Here Note If product has no serial number record Note Some parts are listed and shown for month and year of purchase instead illustration purposes only and are not available individually as replacement parts Page 6 For technical questions please call 1 888 866 5797 Item 61700 Assembly Diagram MACHINERY Page 7 ns please call 1 888 866 5797 For technical questio Item 61700 Limited 90 Day Warranty Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase This warranty does not apply to damage due directly or indirectly to misuse abuse negligence or accidents repairs or alterations outside our facilities criminal activity improper installation normal wear and tear or to lack of maintenance We shall in no event be liable for death injuries to persons or property or for incidental contingent special or consequential damages arising from the use of our product Some states do not allow the exclusion or limitation of incidental or consequential damages so the abov
5. chnical questions please call 1 888 866 5797 be understood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator Item 61700 Assembly Instructions Ad 1 On the Wooden Board 1 measure 3 3 8 from each end of the Wooden Board Mark a line with a pencil Line up the wide end of the Leg Mounting Bracket 2 with the line There are four holes in the primary plate of the Leg Mounting Bracket Use four Screws 8 to attach the Bracket to the Wooden Board through those holes Repeat on the opposite end of the Wooden Board Place the end of a leg into one side of the Leg Mounting Bracket lined up with the mounting holes in the walls of the Bracket The open side of the leg should face inward See Figure A Wooden Board 1 Mounting Bolt 9 Bracket 2 Leg 3 Nut 10 Figure A Secure the Leg to the Bracket with Bolt 9 and Nut 10 Tighten enough to allow limited movement Repeat with the remaining Legs Place a Foot 5 on the end of each Leg 3 Note the angle of the Foot the longer edge of the Foot should be on the outer side of the Leg See Figure B Foot 5 outer side of Leg 3 Figure B Item 61700 For technical questions please call 1 888 866 5797 Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document including all text under subheadings therein before set up
6. e limitation of exclusion may not apply to you THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS To take advantage of this warranty the product or part must be returned to us with transportation charges prepaid Proof of purchase date and an explanation of the complaint must accompany the merchandise If our inspection verifies the defect we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement We will return repaired products at our expense but if we determine there is no defect or that the defect resulted from causes not within the scope of our warranty then you must bear the cost of returning the product This warranty gives you specific legal rights and you may also have other rights which vary from state to state CENTRAL CS ACHINERY 3491 Mission Oaks Blvd PO Box 6009 Camarillo CA 93011 888 866 5797
7. nual must be performed only by a qualified technician AWARNING TO PREVENT SERIOUS INJURY FROM TOOL FAILURE Do not use damaged equipment If damage is found have the problem corrected before further use Cleaning Maintenance and Lubrication 1 BEFORE EACH USE inspect the general 2 AFTER USE wipe external surfaces condition of the tool Check for of the tool with clean cloth e loose hardware e misalignment or binding of moving parts e cracked or broken parts and e any other condition that may affect its safe operation Item 61700 For technical questions please call 1 888 866 5797 Page 5 Parts List and Diagram Parts List Parts for each sawhorse 2 sawhorses included Part Description _ _ _ 9 Bolt M6 x 3 4 Nut M6 Nylon Insert Nut M6 Split Lock Washer Carriage Bolt M5 x 5 16 ocking Knob Nut M5 16 8 WoodScrew ss Y 8 PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS DOCUMENT AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BU
8. or use of this product Attach the Brace 4 between two of the Legs on one side of the Sawhorse See Figure C Bolt 14 Brace 4 Figure C a Press the flat side of the Brace against the outside of the Legs b Secure with four Carriage Bolts 14 and Nuts 15 c Leave all hardware in this step slightly loose for now d Repeat on the opposite side Attach the closed end of the Leg Locking Brace 6 between two of the Legs on one end of the Sawhorse using a Bolt 9 Washer 12 and Nylon Insert Nut 11 Ensure that the hook opening of the Leg Locking Brace faces toward the ground See Figure F Tighten the Bolt and Nut enough to allow movement See Figure D and Figure E Bolt Leg Locking Brace 6 Figure D Nylon Insert Nut 10 Leg Locking Brace 6 Figure E Page 3 Install a Bolt on the opposite Leg a Insert a Bolt through the mounting holes from the inside of the Leg b Add a Split Lock Washer 13 and Nut to the outer side of the Leg leaving the Bolt exposed c Tighten securely d Hook the open end of the Leg Locking Brace over the exposed Bolt e Twist the Locking Knob 7 on the exposed threads of the Bolt to clamp the Brace in place f Hand tighten See Figure F CENTRAL CE JMACHINERY Page 4 For technical questions please call 1 888 866 5797 hook end of Leg Locking Brace 6 Leg Locking Brace 6 Bolt 9 Locking Knob 7
Download Pdf Manuals
Related Search