Harbor Freight Tools Electric Multipurpose Sharpener Product manual
Contents
1. PROFESSIONAL CHICAGOGELECTRIC POWER TOOLS MULTI PURPOSE ELECTRIC SHARPENER exes 99823 SET UP AND OPERATING INSTRUCTIONS Visit our website at http www harborfreight com Read this material before using this product Failure to do so can result in serious injury SAVE THIS MANUAL Copyright 2008 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools Diagrams within this manual may not be drawn proportionally Due to continuing improve ments actual product may differ slightly from the product described herein Tools required for assembly and service may not be included For technical questions or replacement parts please call 1 800 444 3353 Manual Revised 10e SAVE THIS MANUAL Keep this manual for the safety warnings and precautions assembly operating inspection maintenance and cleaning procedures Write the product s serial number in the back of the manual near the assembly diagram or month and year of purchase if product has no number Keep this manual and the receipt in a safe and dry place for future reference IMPORTANT SAFETY INSTRUCTIONS In this manual on the labeling and all other information provided with this product This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety m2. normal wear and tear or to lack of maintenance We shall in no event be liable for death injuries to persons or property or for incidental contingent special or consequential damages arising from the use of our product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS SKU 99823 For technical questions please call 1 800 444 3353 To take advantage of this warranty the product or part must be returned to us with transportation charges prepaid Proof of purchase date and an explanation of the complaint must accompany the merchandise If our inspection verifies the defect we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement We will return repaired products at our expense but if we determine there is no defect or that the defect resulted from causes not within the scope of our warranty then you must bear the cost of returning the product This warranty gives you specific legal rights and you may also have other rights which vary from state to state 3491 Mission Oaks Blvd PO Box 6009 Camarillo CA 93011 800 444 3353 Page 12
3. the beginning of this manual including all text under subheadings therein before set up or use of this product TO PREVENT AWARNING SERIOUS INJURY FROM ACCIDENTAL OPERATION OR ELECTRIC SHOCK Before tool assembly or adjustment make sure the tool s switch is turned off and the cord is unplugged Note For additional information regarding the parts listed in the following pages refer to the Assembly Diagram near c Straight Edge Chisel and Plane the end of this manual Blade Attachment 2 All three Attachments can be easily snapped on and off the front of Assembling the Sharpening Attachments the Electric Sharpener Slide the 1 There are three sharpening Attachment into or out of the grooved Attachments for this Multi purpose channels on each side of the Motor Electric Sharpener Housing All three snap in place Figure 1 a Standard Knife and Scissor Attachment SKU 99823 For technical questions please call 1 800 444 3353 Page 5 SKU 99823 OPERATION Read the ENTIRE IMPORTANT A SAFEGUARDS section at the beginning of this manual including all text under subheadings therein before set up or use of this product Using the High Speed Drill Bit Attachment Slide the High Speed Drill Bit Attachment onto the Motor Housing until it snaps at the bottom Figure 4 Grinding Wheel 6 Clamp Assembly 17 18 19 Clamp Holder 15 16 V Guide Setting Slot Remove Clamp Assembly 17
4. to the State of California to cause cancer and birth defects or other reproductive harm Wash hands after handling California Health amp Safety Code 25249 5 et seq The warnings precautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur It must be understood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator Specific Safety Rules Grinding wheel MUST BE rated to at least 4800 RPM Wear ANSI approved safety goggles and heavy duty work gloves during set up and use 3 Knives with serrated edges are a good example of blades that may not be suited for this Electric Sharpener 4 This Multi purpose Electric Sharpener is not recommended for professional applications SAVE THESE INSTRUCTIONS SPECIFICATIONS 4800 RPM Rocker Type ON OFF Drill Bits 1 8 3 8 3 10mm Applications Chisels Planer Blades 1 4 2 W Most Knives and Scissors Minimum size drill bit 1 8 UNPACKING When unpacking check to make sure that the item is intact and undamaged If any parts are missing or broken please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible REV 08k For technical questions please call 1 800 444 3353 Page 4 ASSEMBLY Figure 2 Read the ENTIRE IMPORTANT A SAFEGUARDS section at
5. 18 19 from Clamp Holder 15 16 and insert itin the Setting Slot at the left hand side of the module by aligning the slots at the sides of Clamp Holder 15 16 with the tabs of the Setting Slot Clamping nut should be on the top side Slide the V Guide all the way down and hold in place with one hand Insert the bit into the Clamp and while pushing it into the V rotate the bit so that all four corners of the bit would touch the walls of the V Guide Only sharpen Right Hand twist drill bits Ease back the V Guide until the bit rests against the stopper at the center of the V Turn the Clamping Nut clockwise to securely hold the bit Do Not Over tighten Pull back on the V Guide and remove the Clamp Assembly 17 18 19 Push top of the sharpener assembly forward away from the sharpening stone and insert the Clamp into the Clamp Holder 15 16 Start the motor by pushing the I on the switch Wait until the grinding wheel picks up speed In a uniform slow and steady motion swing the Clamp Assembly back and forth until grinding noise subsides Turn the switch to its off position Lift the Clamp Assembly 17 18 19 and flip it upside down Repeat steps 6 through 8 to sharpen the other face of the bit Note SHARPEN BOTH FACES OF THE BIT EQUALLY otop the motor remove the bit with the Clamp Assembly 17 18 19 and inspect both faces of the bit If further grinding is necessary repeat
6. catch at the lower side of the attachment SKU 99823 For technical questions please call 1 800 444 3353 Page 7 2 Switch the Motor on Figure 5 Guide Slots 3 Hold the knife handle towards you and insert the heel end of the blade into the Guide Slot See Figure 5 for all directions in this section 4 As soon as the blade touches the Grinding Wheel 6 slide it with light even pressure across the Grinding Wheel 6 surface to the knife tip then remove it Do not use excess pressure 5 Insert the other side of the knife into the opposite guide slot and repeat the same procedure as in number 3 above 6 Continue this procedure alternating sides of the knife blade until a sharp edge is attained 7 Turn off the power to the Motor Housing with Switch 3 Using Scissors Attachment 1 Slide the Scissors and Knife Sharpening attachment into the Motor Housing 1 making sure that the latch snaps into the catch at the lower side of the attachment 2 Attach the Scissors and Knife Sharpening Attachment to the grinding wheel side of the Motor Housing 1 making sure that the SKU 99823 latch snaps into the catch at the lower side of the attachment Turn on the Power Switch 3 and allow the motor speed to stabilize Open the scissors fully Note This tool can only sharpen those scissors which spread fully past 90 Keeping the idle blade to the right hand side of the Motor Housing 1 p
7. chnical questions please call 1 800 444 3353 Page 10 PARTS LIST Partt Description Q ty 1 MotorHousing 1 2 Base with mounting holes 1 3 Switch Rocker type ON OFF 1 4 Motor J 1 o 5 j WheelVave 1 6 Grinding Wheel 1 7 SignforRotational Direction 1 8 Nt O 1 9 PowerCord J 1 12 PCB 1 13 RubberFoot J J 4 14 Secew o 4 15 ClampHolder 1 16 Clamp J 1 17 Turn Nutfor Clamp Holder 1 Locking Nut for Clamp Holder PARTS LIST e Top Lock Nut for Clamp Holder Located Block 1 H EHE Attachment a Blade Attachment Magnet Guard Magnet ASSEMBLY DIAGRAM SKU 99823 24 16 ie 18 32 30 For technical questions please call 1 800 444 3353 lo 22 e0 19 17 29 27 Page 11 LIMITED 90 DAY WARRANTY Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase This warranty does not apply to damage due directly or indirectly to misuse abuse negligence or accidents repairs or alterations outside our facilities criminal activity improper installation
8. e held firmly by hand during actual grinding 4 Turn on the Power Switch 3 and allow the motor speed to stabilize Slide the Support Plate making sure that blade edge touches the wheel Note Do not force the blade onto the Grinding Wheel Stop the motor and remove the blade to inspect for proper and uniform bevel angle and sharp edge If necessary bevel angle may be slightly re adjusted When sharpening cold chisels stop the Motor turn the blade upside down repeat steps 4 through 6 to sharpen the other face To prevent accidents after each use turn off the tool and disconnect it for its power supply Clean then store indoors out of children s reach NOTE For extra fine edge use of whet For technical questions please call 1 800 444 3353 stone and honing oil is recommended after completion of sharpening with this tool Page 9 INSPECTIONAND TO PREVENT SERIOUS INJURY FROM FAILURE MAINTENANCE Do not use if damaged f TO PREVENT abnormal noise or vibration AWARNING SERIOUS INJURY occurs have the problem FROM ACCIDENTAL corrected before further use OPERATION OR ELECTRIC BEFORE EACH USE inspect the SHOCK general condition of the Electric Sharpener Check for loose screws misalignment or binding of moving parts cracked or broken parts cord is unplugged damaged electrical wiring and any other condition that may affect its safe operation Before inspection or maintenance
9. essages that follow this symbol to avoid possible injury or death DANGER indicates A DANGER a hazardous situation which if not avoided will result in death or serious injury AWARNING WARNING indicates a hazardous situation which if not avoided could result in death or serious injury SKU 99823 For technical questions please call 1 800 444 3353 CAUTION used ACAUTION with the safety alert symbol indicates a hazardous situation which if not avoided could result in minor or moderate injury NOTICE NOTICE is used to address practices not related to personal injury the safety alert symbol is used to address practices not related to personal injury READ AND UNDERSTAND ALL INSTRUCTIONS When using electrical tools safety precautions should always be followed including the following Work Area Safety 1 Do not use outdoors 2 Close supervision is necessary when any tool is used by or near children 3 Do not let cord hang over edge of table or counter or touch hot surfaces 4 Do not place on or near a hot gas or electric burner or in a heated oven 5 Extreme caution must be used when moving an tool 6 Keep the work area well lit Make sure there is adequate surrounding workspace Keep the work area free of obstructions and other debris Page 2 Electrical Safety To protect against electrical shock do not immerse cord plugs or the main unit in water or
10. make sure the switch is turned off and the Troubleshooting not start 2 Cord not connected 2 Check that cord is plugged in Grinding Wheel not 3 Grinding Wheel may not be true due 4 Check Grinding Wheel for smooth running smoothly to wear during use straight edge and replace if necessary Follow all safety precautions whenever diagnosing or servicing the tool Disconnect power supply before service PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO Record Product s Serial Number Here Note If product has no serial number record month and year of purchase instead Note Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts SKU 99823 For te
11. osition the underside of the blade to be sharpened in the slot across the face of the Attachment Position the blade edge parallel to the right hand side of the grinding wheel and with very light pressure slide the entire length of the blade across the grinding wheel Repeat Step 4 above to sharpen the other blade Alternate between blades until a keen edge is formed across the edges Remove scissors from the sharpener Turn off the Power Switch 3 For technical questions please call 1 800 444 3353 Page 8 SKU 99823 Using the Chisel and Plane Attachment Support Plate with Magnets 29 Figure 6 Motor Housing 1 Base with Mounting Holes 2 Slide the Chisel and Plane sharpening attachment into the Motor Housing 1 making sure that the latch snaps into the catch at the lower side of the attachment Determine the existing blade bevel angle back off the thumb screw and slide the guide platform to the desired angle using the scale and indicator on the face of the attachment Tighten the thumb screw Note To redress the edge to an alternative angle use of a heavy duty grinding set up is recommended Position the chisel against the side lip of the Support Plate 29 and slide the chisel edge down to reach the grinding wheel Note The chisel should be perpendicular to the grinding wheel The magnet on the Support Plate will support the blade in position during set up but the blade must b
12. other liquid Only the non electrical parts of the unit may be immersed for cleaning Thoroughly clean and dry these parts prior to first use and before every subsequent use Unplug from outlet when not in use and before maintenance or cleaning Do not operate any tool with a damaged cord or plug or after the tool malfunctions or has been damaged in any manner Return tool to the nearest authorized service facility for examination repair or adjustment This Electric Sharpener has a polarized plug one blade is wider than the other To reduce the risk of electric shock this plug is intended to fit into a polarized outlet only one way If the plug does not fit fully in the outlet reverse the plug If it still does not fit contact a qualified electrician Do not change the plug in any way Do not use this product in a damp or wet location Do not clean with metal scouring pads Metal pieces can break off the pads and touch electrical parts involving risk of shock Power Cord Safety 1 A short power supply cord is to be provided to reduce risks resulting from becoming entangled in or SKU 99823 N For technical questions please call 1 800 444 3353 tripping over a longer cord Longer extension cords are available and may be used if care is exercised in their use If a long extension cord is used a the marked electrical rating of the detachable power supply cord or extension cord should be at leas
13. steps 3 to 8 However if the result is satisfactory back off the clamping nut and remove the bit CAUTION The bit may be hot Handle with care For technical questions please call 1 800 444 3353 Page 6 10 Disconnect from the electrical outlet wipe the unit to remove dust metal shavings and debris Return the Clamp Assembly 17 18 19 into the Clamp Holder 15 16 Cover and store in a safe location For the drill bit diameter smaller than 9 64 1 Take out Clamp Assembly 17 18 19 from Clamp Holder 15 16 Loosen the Clamp Assembly We Turn the Locking Nut for Clamp Holder 18 in 180 4 Insert the Locking Nut for Clamp Holder 18 with Top Lock Nut for Clamp Holder 19 into the slot of the Turn Nut for Clamp Holder 17 p Tighten the Top Lock Nut for Clamp Holder 19 clockwise Insert Clamp Assembly 17 18 19 into Clamp Holder 15 16 Then the attachment can be for the drill bit diameter smaller than 9 64 NOTE Mastering the setup and grinding the bit will require practice e The module may be pulled back towards the grinding wheel for faster material removal e Clamp assembly may need to be inserted partially and as the faces are sharpened it may need to be pushed down until the Clamp Holder rests at the bottom of its cavity Knives Slide the Scissors and Knife Sharpening attachment into the Motor Housing 1 making sure that the latch snaps into the
14. t as great as the electrical rating of the tool if the tool is of the grounded type the extension cord should be a grounding type 3 wire cord and the longer cord should be arranged so that it will not drape over the counter top or tabletop where it can be pulled on by children or tripped Over General Safety The use of accessory attachments not recommended by the tool manufacturer may cause injuries To disconnect turn any control to Off then remove plug from wall outlet Do not use tool for other than intended use Maintain labels and nameplates on the tool These carry important safety information If unreadable or missing contact Harbor Freight Tools for a replacement Do not store anything other than the manufacturer s recommended accessories in this unit when not in use Page 3 10 SKU 99823 This product is not a toy Keep it out of reach of children when children are not being closely supervised People with pacemakers should consult their physician s before use Electromagnetic fields in close proximity to heart pacemaker could cause pacemaker interference or pacemaker failure WARNING The brass components of this product contain lead a chemical known to the State of California to cause birth defects or other reproductive harm California Health amp Safety code 25249 5 et seq WARNING Handling the cord on this product will expose you to lead a chemical known
Download Pdf Manuals
Related Search