Harbor Freight Tools Drip Irrigation Kit Product manual
Contents
1. 10 DRIP NOZZLE WATERING DRIP KIT Model 93261 Model 46095 ASSEMBLY AND OPERATING INSTRUCTIONS Due to continuing improvements actual product may differ slightly from the product described herein Distributed Exclusively by HARBOR FREIGHT ci TOOLS Wie 3491 Mission Oaks Blvd Camarillo CA 93011 Visit our Web site at http www harborfreight com TO PREVENT SERIOUS INJURY READ AND UNDERSTAND ALL WARNINGS AND INSTRUCTIONS BEFORE USE Copyright 2005 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools For technical questions and replacement parts please call 1 800 444 3353 REV 07 05 PRODUCT SPECIFICATIONS Hose Length Diameter Model 93261 150 Ft 4 O D x 3 16 I D Model 46095 100 Ft 4 O D x 3 16 I D Maximum 55 PSI Operating Pressure Accessories Faucet to Hose Connector Qty 1 Threaded Adapter Coupler Qty 1 Water Pressure Regulator Qty 1 Faucet Gasket Qty 1 Faucet Gasket w Filter Screen Qty 1 Hose Tee Qty 14 Plastic Tube Qty 5 Tie Down Stake Qty 15 Plastic Hose Coupler Qty 2 In Line Hose Coupler w Drip Nozzle Flow Thru w Small Pin Hole Qty 10 Hose Nail Down Clip Qty 10 Faucet Connector Qty 1 Terminal Drip Nozzle w No Pin Hole Qty 10 Approximate Unit Weight 3 20 Pounds SAVE2. Adapter Coupler 3 Water Pressure Regulator 4 Faucet Gaskets 5 and 6 and Hose 1 or 1A assemble and secure these parts to the water faucet or water valve as illustrated See Figure A ae at FAUCET eo THREADED ADAPTER COUPLER 3 FAUCET GASKET WITH FILTER SCREEN FAUCET GASKET WATER PRESSURE 6 WITH FILTER SCREEN REGULATOR O 6 4 amp WATER PRESSURE REGULATOR FAUCET TO HOSE 4 hacia Sah FAUCET TO HOSE 2 CONNECTOR 2 HOSE HOSE 1 OR 1A 1 OR 1A SKU T For technical questions please call 1 800 444 3353 Page 4 FIGURE A Hand tighten all connections if possible If pliers are used care must be taken not to overtighten components as they may break See Figure A Cut the end of the Hose 1 or 1A at an angle This will allow easier insertion into the Faucet Hose Connector 2 Press and twist hose in 1 2 inch See Figure A Route the Hose along the desired watering locations See Figure B If necessary use the Hose Nail down Clips 12 to secure the Hose to a wooden rail pot or other fixture The Tie down stakes can be used to secure the Hose to dirt within the pot or on the ground Decide on how the Drip Nozzles 11 amp 14 will be connected Pots over 8 inches in diameter may require 2 or more Drip Nozzles In planter boxes place the Drip Nozzles every 12 inches Main Hose runs should not be over 50 feet in length Hose connections to hanging plants should not be over 10
3. THIS MANUAL You will need the manual for the safety warnings and precautions assembly instructions operating and maintenance procedures parts list and diagram Keep your invoice with this manual Write the invoice number on the inside of the front cover Keep the manual and invoice in a safe and dry place for future reference UNPACKING When unpacking check to make sure that all parts listed in the Parts List on page 7 are included If any parts are missing or broken please call Harbor Freight Tools at the number shown on the front cover of this manual as soon as possible GENERAL SAFETY WARNINGS AND PRECAUTIONS WARNING When using tools to install this product basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment Read all instructions before using this product Keep work area clean Cluttered areas invite injuries 2 Observe work area conditions Do not use machines or power tools in damp or wet locations Don t expose to rain Keep work area well lighted SKU ree For technical questions please call 1 800 444 3353 Page 2 14 Do not use electrically powered tools in the presence of flammable gases or liquids Keep children away Children must never be allowed in the work area Do not let them handle machines tools or extension cords Store idle equipment When not in use tools must be stored in a dry location to inhibit rust Always lock up tools
4. and keep out of reach of children Do not force the product It will do the job better and more safely at the rate for which it was intended Do not use inappropriate attachments in an attempt to exceed the product s capacity Use the right product for the job Do not attempt to force a small product or attachment to do the work of a larger industrial product There are certain applications for which this product was designed Do not modify this product and do not use this product for a purpose for which it was not intended Dress properly Do not wear loose clothing or jewelry as they can be caught in moving parts Protective electrically non conductive clothes and non skid footwear are recommended when working Wear restrictive hair covering to contain long hair Use eye and ear protection Always wear ANSI approved impact safety goggles when setting up this product and when working with tools and equipment Do not overreach Keep proper footing and balance at all times Maintain products with care Inspect all components and the hose periodically and if damaged have defective items repaired or replaced by an authorized technician Disconnect when not in use When the Drip Kit is not being used disconnect from the water source and store all components in a dry location Stay alert Watch what you are doing use common sense Do not assemble or operate any product when you are tired Check for damaged parts Before using any p
5. Y THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO SKU A For technical questions please call 1 800 444 3353 Page 6 PARTS LIST AND ASSEMBLY DIAGRAM Part Description ty Hose Neoprene 1 4 O D x 3 16 I D Model 93261 Hose Neoprene 1 4 O D x 3 16 I D Model 46095 2 Faucet to Hose Connector Tt 3 Threaded Adapter Coupler Tt 4 Water Pressure Regulator Tt 5 FaucetGasket o O i i 6 Faucet Gasket with FilterScreen Tt 7 HoseT Tee o Oda i i ca N Pasie ub E 9 Tie Down Stake O OJ 10 Plastic Hose Coupler In Line Hose Coupler with Drip Nozzle 10 Flow Thru Has Small Pin Hole Faucet Cedo Terminal Drip Nozzle Has No Pin Hole 2 Beer 3 4 5 NOTE Some parts are listed and shown for illustration purposes only an
6. d are not available individually as replacement parts SKU yo For technical questions please call 1 800 444 3353 Page7 13
7. feet in height Use Scissors to cut the Hose at the desired location and length The Hose Tees 7 can be used to tap off the main Hose line Example 1 e o9 _o __ _e _ __o _ __9 _ __0_ o _ Example 2 Plastic Tube Water Faucet Hose Tees FIGURE B 10 Turn on the water to flush out the Hose 1 or 1A before taping off and closing the end s This will blow out any debris within the Hose NOTE Do not exceed the maximum 55 PSI water pressure for the Hose 11 Use the Plastic Tubes 8 to close an open Hose 1 or 1A end by SKU 93261 For technical questions please call 1 800 444 3353 Page 5 46095 doubling over the Hose end and forcing it over the doubled Tube 12 Turn on the water and check each Drip Nozzle for dripping water If the flow is too slow try removing the Water Pressure Regulator 4 and retest the flow once again If there are leaks in the Faucet Couplings hand tighten once again or remove and reassemble them using pipe sealant tape not included on the threads MAINTENANCE 1 Remove and clean out the Faucet Gasket with Filter Screen 6 every month 2 Periodically remove Plastic Tubes 8 connected to Hose ends and turn on the water to blow out any debris oo CAUTION All maintenance service or repairs not mentioned in this manual are only to be attempted by a qualified service techni cian PLEASE READ THE FOLLOWING CAREFULL
8. roduct any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function Check for alignment and binding of moving parts any broken parts or mounting fixtures and any other condition that may affect proper operation Any part that is damaged should be properly repaired or replaced by a qualified technician Do not use the product if it is not working properly Replacement parts and accessories When servicing use only identical replacement parts Use of any other parts will void the warranty Only use SKU 93261 For technical questions please call 1 800 444 3353 Page 3 46095 accessories intended for use with this tool 15 Do not operate this product if under the influence of alcohol or drugs Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs If there is any doubt do not operate the product 16 Maintenance For your safety service and maintenance should be performed regularly by a qualified technician Warning The warnings cautions and instructions discussed in this instruc tion manual cannot cover all possible conditions and situations that may oc cur It must be understood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator OPERATION 1 Using the Faucet Connector 13 Faucet to Hose Connector 2 Threaded
Download Pdf Manuals
Related Search