Harbor Freight Tools Drill Press Extension Table with Fence Product manual
Contents
1. cccccesessseeeeeeeeseeeeeeees 6 OPE Nace seen cence dete tceenuenecakcestevecsectureeeees l INSPECTION AND MAINTENANCE ec eeeeeeeeee l PARTS LIS 0 ere ce oc eee cen E E ESAE 8 ASSEMBLY DIAGRAM cccccceesceeeeseeeeeeeeeeeeeseeeeeeees 8 WV INE Yeas pecye esac eensereseteaten ssesecsgecesusne eenagenteccesskear sere 9 SKU 96395 For technical questions please call 1 800 444 3353 Page 2 Ms SKU 96395 SAVE THIS MANUAL Keep this manual for the safety warnings and precautions assembly operating inspection maintenance and cleaning procedures Write the product s serial number in the back of the manual near the assembly diagram or month and year of purchase if product has no number Keep this manual and the receipt in a safe and dry place for future reference IMPORTANT SAFEGUARDS In this manual on the labeling and all other information provided with this product AWARNING A CAUTION NOTICE CAUTION This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death DANGER indicates a hazardous situation which if not avoided will result in death or serious injury WARNING indicates a hazardous situation which if not avoided could result in death or serious injury CAUTION used with the safety alert symbol indicates a hazardous situation which if not avoided co2. of the Full Thread Rods 11 Thread one knob 5 onto each Full Thread Rod 11 See Figure 1 and the Assembly Diagram on page 8 ATTACHING THE DRILL PRESS TABLE Wipe down the surface of the drill table Lay the Drill Press Table 4 onto the table of your drill press and line up the drill chuck with the Insert Block 14 The Insert Block 14 is used to prevent tear out from the drill bit exiting the work piece when drilling thin materials Tighten the Hold Down Clamps 12 by turning the Knobs 5 clockwise until the Hold Down Clamps 12 are snug against the bottom of the drill table Always tighten both clamps to insure a secure connection SKU 96395 For technical questions please call 1 800 444 3353 Page 6 OPERATION Read the ENTIRE IMPORTANT SAFEGUARDS section at the beginning of this manual including all text under subheadings therein before set up or use of this product 1 Wipe down the Drill Press Table Top before each use See Cleaning on page 6 2 For safety turn off the drill press and disconnect its power supply before use 3 After the Drill Press Table 4 is mounted to your drill press see Attaching the Drill Press Table on page 6 set the Drill Press Fence 2 by loosening the two T Slot Bolts 7 Slide the Drill Press Fence to where you need to stop your material then turn the Knobs 5 clockwise to secure it in place 4 The Stop Block 3 can be mounted into the Drill Press Fence 2 usi
3. CENTRAL MACHINERY PACCCSSOV1ES DRILL PRESS TABLE AND FENCE exe 1 96395 ASSEMBLY AND OPERATION INSTRUCTIONS CE AL MACHINER 8 Drill Press bad pm Drill Press not included Diagrams within this manual may not be drawn proportionally Due to continuing improvements actual product may differ slightly from the product described herein Distributed Exclusively by Aa HARBOR FREIGHT 3491 Mission Oaks Blvd Camarillo CA 93011 Visit our website at http www harborfreight com Read this material before using this product Failure to do so can result in serious injury SAVE THIS MANUAL Copyright 2007 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools For technical questions or replacement parts please call 1 800 444 3353 CONTENTS IMPORTANT SAFEGUARDS cccceceeeeeeeeeeeneeeeeeenees 3 Work Area Safety ccccccceseecseecneecnseceescnsseenseoneeonseoeeeseeesens 3 General Safety acceso cs csre ce tee cect ctenc tees cectecccnecceecenesseceeetecaaencseeee SPECIFICATIONS ccccccceseccneeeseenecneecnsseesceneonssonenens D UNPACKING cece ecceeecceeceeeceeseeeeeeeseneeeeseeeseeseeneeeesanenes 9 CLEANING oore E E E D ASSEMBLY sorreran E E aea R EE 5 Attaching the Drill Press Table
4. ING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO SKU 96395 For technical questions please call 1 800 444 3353 Page 7 PARTS LIST Te tape a o Flathead Tapping Screw 6 40 Flathead Tapping Screw 6 6 T Slot Bolt M8 X 1 9 16 T Slot Bolt M8 X 3 9 16 ASSEMBLY DIAGRAM SKU 96395 For technical questions please call 1 800 444 3353 Page 8 LIMITED 90 DAY WARRANTY Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase This warranty does not apply to damage due directly or indirectly to misuse abuse negligence or accidents repairs or alterations outside our facilities criminal activity improper installation normal wear and tear or to lack of maintenance We shall in no event be liable for death injuries to persons or property or for incidental contingent special or consequential damages arising from the use of our product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS To take advantage of this warranty the product or part must be
5. is turned off and the cord is unplugged Do not immerse motor heating element cord or plug of the drill press in water or any other liquid Wipe down with a Dry with a soft cloth ASSEMBLY Read the ENTIRE IMPORTANT SAFEGUARDS section at the beginning of this manual including all text under subheadings therein before set up or use of this product Before Drill Press Table s assembly or adjustment make sure AWARNING the the drill press to which it will be attached is turned off and the cord is unplugged SKU 96395 For technical questions please call 1 800 444 3353 Page 5 Note For additional information regarding the parts listed in the following pages refer 1 to the Assembly Diagram on page 8 of this manual Wipe down the Drill Press Table before assembly as explained in the Cleaning section Figure 1 Attach the Drill Press Fence 2 to the T Tracks 1 using two T Slot Bolts 7 Thread two Knobs 5 onto the top of each T Slot Bolt 7 See Figure 1 If needed for use with repetitive bores attach the Stop Block 3 to the Drill Press Fence 2 using one T Slot Bolt 6 and thread the Knob 5 onto the end of the T Slot Bolt 6 See Assembly Diagram on page 8 Insert the two T Cap Nuts 8 into slots in the bottom of the Drill Press Table top 4 and insert three Screws 9 into each T Cap Nut 8 Mount one Full Thread Rod 11 into each T Cap Nut 8 and one of the Hold Down Clamps 12 onto each
6. ng a T Slot Bolt 6 and Knob 5 Use the Stop Block 3 when repetitive bores are being made When the Stop Block 3 is not being used it may be removed INSPECTION AND MAINTENANCE Before Drill Press Table inspection or maintenance make AWARNING sure the power switch to the drill press is turned off and the cord is unplugged Do not use damaged tools If abnormal noise or vibration occurs have the problem corrected before further use 1 BEFORE EACH USE inspect the general condition of the Drill Press Table Check for loose screws misalignment or binding of moving parts cracked or broken parts and any other condition that may affect its safe operation 2 Make sure the Drill Press Table is securely fastened to the drill press PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARIS
7. ormation If unreadable or missing contact Harbor Freight Tools for a replacement This Drill Press Table is not a toy Keep it out of reach of children when children are not being closely supervised The warnings precautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur It must be understood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator AA SAVE THESE INSTRUCTIONS SKU 96395 For technical questions please call 1 800 444 3353 Page 4 SPECIFICATIONS Table Top and Fence Particle Board T Track and Hold Down Clamps Aluminum Knobs Thermoplastic Hardware Carbon Steel Overall Dimensions 11 5 8 L X 23 7 8 W X 1 H Construction Materials NOTE Drill Press Table will fit the following Drill Presses offered by Harbor Freight Tools SKU 44505 SKU 44836 and SKU 44506 UNPACKING When unpacking check to make sure that the item is intact and undamaged If any parts are missing or broken please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible CLEANING Read the ENTIRE IMPORTANT SAFEGUARDS section at the beginning of this manual including all text under subheadings therein before set up or use of this product AWARNING RISK OF SHOCK Before cleaning this Drill Press Table make sure the drill press switch
8. returned to us with transportation charges prepaid Proof of purchase date and an explanation of the complaint must accompany the merchandise If our inspection verifies the defect we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement We will return repaired products at our expense but if we determine there is no defect or that the defect resulted from causes not within the scope of our warranty then you must bear the cost of returning the product This warranty gives you specific legal rights and you may also have other rights which vary from state to state 3491 Mission Oaks Blvd PO Box 6009 Camarillo CA 93011 800 444 3353 Record Product s Serial Number Here Note If product has no serial number record month and year of purchase instead Note Some parts are listed and shown for illustration purposes only and are not avail able individually as replacement parts SKU 96395 For technical questions please call 1 800 444 3353 Page 9
9. uld result in minor or moderate injury NOTICE is used to address practices not related to personal injury CAUTION without the safety alert symbol is used to address practices not related to personal injury READ AND UNDERSTAND ALL INSTRUCTIONS When using electrical appliances safety precautions should always be followed including the following Work Area Safety Disconnect power to drill press before installation or adjustments For technical questions please call 1 800 444 3353 Page 3 O a S p Wear ANSI approved safety goggles and heavy duty gloves during installation and use Secure this Drill Press Table before use Inspect before each use Do not use this Drill Press Table if it is damaged in any way Use this Drill Press Table for its intended purpose only Close supervision is necessary when any tool is used by or near children Extreme caution must be used when moving this Drill Press Table and Fence Keep the work area well lit Make sure there is adequate surrounding workspace Keep the work area free of obstructions and other debris Electrical Safety Always follow all safety warnings and instructions found in AWARNING the manufacturers manual for the drill press this Drill Press Table will be attached to General Safety The use of accessory attachments not recommended by the manufacturer may Cause injuries Maintain labels and nameplates on the appliance These carry important safety inf
Download Pdf Manuals
Related Search