Harbor Freight Tools Chain Saw Chain_Breaker/Spinner Product manual
Contents
1. Spinner Die 3 11 and Thrust Die 11 during operation Severe pinch haz ard exists at these areas during operation To Disassemble Break the Chain 1 For technical questions please call 1 800 444 3353 Fit the chain to the correct notch on the Anvil 2 Be sure the rivet lines up under the hole in the bottom of the slot in the Anvil Position the Anvil 2 and chain di rectly under the Breaker Punch 19 Lower the Breaker Lever 3 to lower the Breaker Punch 19 onto the rivet Be sure the Breaker Punch is centered on the rivet and the rivet is centered over the hole in the bottom of the Anvil Pull down on the Breaker Lever 3 to drive the rivet out of the chain If the rivet binds recheck the align ment of all parts Apply a small amount of penetrating oil Retry driv ing the rivet out of the chain When the rivet has been driven out remove the chain from the Anvil 2 Check for any damage to the links To Reassemble Spin the Chain 1 Select either the Large or the Small Spinner and Thrust Dies 11 and 12 and insert into the Spinner Sleeve 10 and Thrust Handle 13 respec tively Always use a matched set of dies do not mix sizes Apply a small amount of light grease to the rivet Insert the rivet into place loosely assembling the chain Drape the chain over the Guide Wheels 4 to hold it in place for spin ning The position of the wheels can be adjusted using the Wheel Lo2. CENTRAL MACHINERY CHAINSAW CHAIN BREAKER SPINNER Ur r1 99835 ASSEMBLY OPERATING AND MAINTENANCE INSTRUCTIONS Diagrams within this manual may not be drawn proportionally Due to continuing improvements actual product may differ slightly from the product described herein Distributed exclusively by Harbor Freight Tools 3491 Mission Oaks Blvd Camarillo CA 93011 Visit our website at http www harborfreight com Read this material before using this product Failure to do so can result in serious injury SAVE THIS MANUAL Copyright 2008 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools For technical questions or replacement parts please call 1 800 444 3353 SAVE THIS MANUAL Keep this manual for the safety warn ings and precautions assembly operat ing inspection maintenance and cleaning procedures Write the product s serial number in the back of the manual near the assembly diagram or month and year of purchase if product has no number Keep this manual and the receipt in a safe and dry place for future reference IMPORTANT SAFETY INSTRUCTIONS In this manual on the labeling and all other information provided with this product This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all s
3. Flat Bearing 1 19 Breaker Punch 1 10 Spinner Sleeve 1 20 Hex Wrench m2 5 1 21 Tool Holder 1 SKU 99835 For technical questions please call 1 800 444 3353 Page 7 LIMITED 90 DAY WARRANTY Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards and warrants to the original purchaser that this prod uct is free from defects in materials and workmanship for the period of 90 days from the date of purchase This warranty does not apply to damage due directly or indirectly to misuse abuse negligence or accidents repairs or alterations outside our facilities criminal activity improper installation normal wear and tear or to lack of maintenance We shall in no event be liable for death injuries to persons or property or for incidental contingent special or consequential damages arising from the use of our product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS WARRANTY IS EXPRESS LY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS To take advantage of this warranty the product or part must be returned to us with transportation charges prepaid Proof of purchase date and an explanation of the com plaint must accompany the merchandise If our inspection verifies the defect we will ei ther repair or replace the produc
4. afety messages that follow this symbol to avoid possible injury or death 44 DANGER a hazardous situation which if not avoided will result in death or serious injury AWARNING VARNING indicates a hazardous situation which if not avoided could result in death or serious injury DANGER indicates SKU 99835 For technical questions please call 1 800 444 3353 CAUTION used ACAUTION with the safety alert symbol indicates a hazardous situation which if not avoided could result in minor or moderate injury NOTICE NOTICE is used to address practices personal injury not related to CAUTION without CAUTION the safety alert symbol is used to address practices not related to personal injury READALLINSTRUCTIONS Personal Safety Dress Properly Do not wear loose clothing or jewelry They can be caught in moving parts Use of rub ber gloves and substantial footwear is recommended when working out doors Wear protective hair covering to contain long hair 2 Wear ANSI approved safety goggles and heavy duty work gloves Use face or dust mask if operation is dusty 3 Do not Overreach Keep proper foot ing and balance at all times 4 Stay Alert Watch what you are doing Use common sense Do not operate Tool when you are tired Page 2 that may affect its operation A guard Keep hands away from or other part that is damaged should anvil area be properly repaired or replaced b
5. cation reinstalling pins in 2 Use the Tool Base 1 as a template chainsaw chains to mark the bench top Drill two 5 16 1 4 0 325 3 8 holes for mounting bolts not includ Anvil Sizes 0 404 7 16 and ed being careful not to drill into any ae hidden electric or utility lines Mount the Base using bolts washers and UNPACKING nuts not included tighten securely 3 Mount the Breaker Lever 3 into the Breaker Cam 15 Secure the Lever in place using one Hex Set Screw 18 Be sure Lever and Cam turn freely then tighten screw securely us ing included Hex Wrench 20 When unpacking check to make sure that the item is intact and undamaged If any parts are missing or broken please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible 4 Insert the Breaker Punch 19 into the SET UP INSTRUCTIONS Tool Holder 21 Hold in place using Se Se one Hex Screw 18 Tighten securely using included Hex Wrench 20 Read the ENTIRE IMPORTANT SAFETY INSTRUCTIONS section at the Fonctions beginning of this manual E including all text under 1 This tool is intended to break apart subheadings therein before set and reassemble chains for chain up or use of this product saws Note For additional information regarding Available Accessories the parts listed in the following pages Attachments refer to the Assembly Diagram near the end of this manual Use of any AWARNING 2c
6. cessory or Assembly attachment other than those listed below may 1 This tool must be bench mounted be increase the risk of serious fore use To bench mount choose an injury appropriate work bench for mounting The workbench must be solid level and strong enough to support the 1 This Tool includes two sets of Dies for weight of the tool the work material spinning the chain rivets These are to fit the diameter of your chain rivets SKU 99835 For technical questions please call 1 800 444 3353 Page 4 SKU 99835 _ Spinner Die _ Thrust Die Small 5 32 W x 7 32 L 7 32 Dia Cup Large 7 32 W x 11 32 L 9 32 Dia Cup The Anvil 2 has settings for 6 differ ent chain sizes Chain Pitch and Width 1 4 Pitch 0 233 Wide 0 325 Pitch 0 255 Wide 3 8 Pitch 0 297 Wide 0 404 Pitch 0 326 Wide 7 16 Pitch 0 345 Wide 1 2 Pitch 0 389 Wide When in operation place the Anvil as required to position the chain directly under the Breaker Punch 19 OPERATING INSTRUCTIONS A Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product Before operating the Chain Breaker wear ANSI approved safety goggles and other safety gear Safety gog gles and other safety gear are sold separately Keep hands away from Breaker Punch 19 Spin ner Sleeve 10
7. cking Screws 5 Be sure the rivet is cen tered on the Dies Page 5 4 Rotate the Thrust Handle 13 clock wise until the chain rivet is held against the Spinner Die 11 5 Check again to be sure the rivet is lined up with the Dies and the open ings in the chain links 6 Apply a small amount of oil to the faces of the Dies 11 and 12 7 Turn the Spinner Handle 7 clock wise to begin forming the rivet head At the same time slowly turn the Thrust Handle 13 to keep the rivet centered and provide resistance to the pressure applied by the Spinner Die 8 Once the rivet head is formed turn both the Spinner Handle 7 and Thrust Handle 13 counterclockwise to release the chain 9 Check the rivet to be sure is is prop erly formed Check the chain to be sure it is not damaged and moves freely MAINTENANCE AND SERVICING Mn not specifically explained in this manual must be performed only by a qualified technician SKU 99835 For technical questions please call 1 800 444 3353 AWARNING TO PREVENT SERIOUS INJURY FROM TOOL FAILURE Do not use damaged equipment If abnormal noise or binding occurs have the problem corrected before further use Cleaning Maintenance and Lubrication 1 BEFORE EACH USE inspect the general condition of the Tool Check for loose screws misalignment or binding of moving parts cracked or broken parts and any other condition that may affect its safe operati
8. on 2 AFTER USE clean external surfaces of the Tool with clean moist cloth 3 Occasionally coat bare metal com ponents with a light coating of oil to prevent corrosion 4 Store this tool in a dry location away from moisture or corrosive materials PLEASE READ THE FOLLOW ING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO Page 6 ASSEMBLY DIAGRAM Part Description QTY Part Description QTY 1 Base 1 11 Spinner Die 2 2 Anvil 1 12 Thrust Die 2 3 Breaker Lever 1 13 Thrust Handle 1 4 Guide Wheel 2 14 Spring Pin 1 5 Wheel Locking Screw 2 15 Breaker Cam 1 6 Spinner Grip 1 16 Cam Holder Cover 1 7 Spinner Handle 1 17 Spring 1 8 Hex Nut 1 18 Hex Screw m5 2 9
9. t at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement We will return re paired products at our expense but if we determine there is no defect or that the defect resulted from causes not within the scope of our warranty then you must bear the cost of returning the product This warranty gives you specific legal rights and you may also have other rights which vary from state to state 3491 Mission Oaks Blvd PO Box 6009 Camarillo CA 93011 800 444 3353 Record Product s Serial Number Here Note If product has no serial number record month and year of purchase instead Note Some parts are listed and shown for illustration purposes only and are not avail able individually as replacement parts SKU 99835 For technical questions please call 1 800 444 3353 Page 8
10. y a qualified technician unless indicated Wear thick jeans and elsewhere in this manual steel toed work boots to help prevent injury 8 Keep Hands clear of anvil when caused by flying debris pressing pin Chain Breaker Use and Care SAVE THESE Keep Children Away All visitors INSTRUCTIONS should be kept at a distance from work area When servicing use only identical replacement parts Use Right Tool Do not use Tool for any job except that for which it is intended Do not Force Tool It will do the job better and with less likelinood of injury at the rate for which it was designed Store Idle Tools Indoors When not in use Tools should be stored indoors in dry and high or locked up place out of reach of children Maintain Tool With Care Keep tool maintained to reduce the risk of injury Follow instructions for lubricat ing and changing accessories Keep handles dry clean and free from oil and grease Check Damaged Parts Before further use of the Tool a guard or other part that is damaged should be carefully checked to determine that it will operate properly and per form its intended function Check for alignment of moving parts binding of moving parts breakage of parts mounting and any other condition SKU 99835 For technical questions please call 1 800 444 3353 Page 3 SPECIFICATIONS and pressure applied to the tool dur ing chain breaking and rivet spinning Removing and Materials Appli
Download Pdf Manuals
Related Search