Harbor Freight Tools 95029 User's Manual
Contents
1. Collet and Grinding Drum in place See Figure B 5 Connect the air supply hose to the Air Inlet 13 Turn on the air compressor and set its regulator to the recommended 90 PSI for the Die Grinder 6 In order to keep the air supply hose out of the way hang it over your shoulder IMPORTANT Grip the Die Grinder firmly with both hands Trip the Lever Pin 15 with your finger Then slowly apply hand pressure to the Lever 14 until the desired speed is obtained See Figure C NOTE The Die Grinder always turns the Grinding Drum clockwise reference while holding the tool as you would when operating it Lever 14 Lever Pin 15 _ a li i Figure C SKU 95029 For technical questions please call 1 800 444 3353 Page 5 10 11 12 Assembly and Operation Instructions continued With a firm grip on the Die Grinder lightly apply the Grinding Drum to the workpiece slowly and steadily moving the Grinding Drum to the right and left until you have achieved the desired appearance finish on the workpiece Once the work is completed release the hand pressure on the Lever 14 The Lever Pin 15 will automatically return to its locked position to prevent the Lever from ac cidentally being activated Turn off the air compressor Trip the Lever Pin 15 with your finger and slowly squeeze the Trigger 14 to release any remaining air pressure from the Die Grinder Then dis connect the air hose from the to2. ALLATION OF REPLACEMENT PARTS THERETO SKU 95029 For technical questions please call 1 800 444 3353 Page 8
3. CENTRAL PNEUMATIC TET y REE s SERRE p Professional 1 4 COMPOSITE AIR DIE GRINDER Model ASSEMBLY AND OPERATING INSTRUCTIONS Due to continuing improvements actual product may differ slightly from the product described herein 3491 Mission Oaks Blvd Camarillo CA 93011 Visit our Web site at http www harborfreight com TO PREVENT SERIOUS INJURY READ AND UNDERSTAND ALL WARNINGS AND INSTRUCTIONS BEFORE USE Copyright 2006 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools For technical questions and replacement parts please call 1 800 444 3353 Specifications 1 4 18 NPT female inlet Maximum RPM 22 000 RPM Loaded Safety Lever 1 15 16 D X 6 3 4 L X 2 13 16 H Save This Manual You will need the manual for the safety warnings and precautions assembly instruc tions operating and maintenance procedures parts list and diagram Keep your invoice with this manual Write the invoice number on the inside of the front cover Keep the manu al and invoice in a safe and dry place for future reference Safety Warnings and Precautions WARNING When using tool basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment Read all instructions before using this tool 1 Keep work are
4. W SEV AAR ANI CENTRAL PNEUMATIC UMITED 1 yEAn oe E N y E v EN py VIS ODN S ON ZZ ZA VY y SS 29 C v 4 Professional Z LA YZ 2 ee WARRANTY KE ON AN we CH Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards WD pr and warrants to the original purchaser that this product is free from defects in materials and workmanship for the ZZA KN period of 1 year from the date of purchase This warranty does not apply to damage due directly or indirectly to Wey AN misuse abuse negligence or accidents repairs or alterations outside our facilities or to lack of maintenance NY SS We shall in no event be liable for death injuries to persons or property or for incidental contingent special eS ch or consequential damages arising from the use of our product Some states do not allow the exclusion or VX K limitation of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS YA Seg WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING lt lt ANY THE WARRANTIES OF MERCHANTABILITY AND FITNESS NY SSS D4 A To take advantage of this warranty the product or part must be returned to us with transportation charges prepaid 2s CA Proof of purchase date and an explanation of the complaint must accompany the merchandise If our inspecti
5. a clean Cluttered areas invite injuries 2 Do not operate pneumatic tools in explosive atmospheres such as in the presence of flammable liquids gases or dust Pneumatic tools create sparks which may ignite flammables 3 Keep children away Children must never be allowed in the work area Do not let them handle machines tools extension cords or air hoses 4 Store idle equipment When not in use tools must be stored in a dry location to inhibit rust Always lock up tools and keep out of reach of children 5 Use the right tool for the job Do not attempt to force a small tool or attachment to do the work of a larger industrial tool There are certain applications for which this tool was designed It will do the job better and more safely at the rate for which it was intended Do not modify this tool and do not use this tool for a purpose for which it was not intended 6 Dress properly Do not wear loose clothing or jewelry as they can be caught in moving parts Protective electrically non conductive clothes and non skid footwear are recommended when working Wear restrictive hair covering to contain long hair SKU 95029 For technical questions please call 1 800 444 3353 Page 2 7 Stay alert Watch what you are doing and use common sense when operating a pneumatic tool Do not use a pneumatic tool while tired or under the influence of drugs alcohol or medication A moment of inattention while operating pneumatic tools may result
6. f California to cause cancer birth defects or other reproductive harm Some examples of these chemicals are lead from lead based paints crystalline silica from bricks and cement or other masonry products arsenic and chromium from chemically treated lumber Your risk from these exposures varies depending on how often you do this type of work To reduce your exposure to these chemicals work in a well ventilated area and work with approved safety equipment such as those dust masks that are specifically designed to filter out microscopic particles California Health amp Safety Code 25249 5 et seq The warnings cautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur It must be understood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator Unpacking When unpacking check to make sure the parts listed on page 7 are included If any parts are missing or broken please call Harbor Freight Tools at the number on the cover of this manual as soon as possible Assembly and Operating Instructions To Attach a Quick Connector 1 lt is recommended that prior to use you attach a Quick Connector not included into the Die Grinder s Air Inlet 13 To do so wrap approximately 3 of pipe thread sealer tape not included around the male threads of a Quick Connector Then firmly tighten t
7. he Quick Connector into the Air Inlet See Figure A Figure A r Quick Connector not included CO Air Inlet 13 Se a ee eee ee RECOMMENDED Air Hose not included Quick Connector to Oiler COMPRESSED not included AIR SYSTEM i t mn i cee a PRE CUIATON aa a teem Sees eos oe _ not included Air Hose Compressor not included a not included Oiler not included Filter not included SKU 95029 For technical questions please call 1 800 444 3353 Page 4 Assembly and Operation Instructions continued Note The Composite Air Die Grinder is designed to be used with grinding attachments backing pads and sanding discs and other small attachments such as the grind ing drum shown in Figure B below To Operate the Die Grinder 1 WARNING Prior to performing any assembly and or adjustment procedures make sure the air supply hose not included is disconnected from the Die Grinder 2 WARNING Always wear ANSl approved safety goggles a full face shield and hearing protection when operating the Die Grinder 3 Use the two Wrenches 30 to loosen the Collet Nut 29 See Figure B below Collet 28 Msi v7 Grinding Drum not included Collet Nut 29 t Wrench 30 Figure B 4 Insert the 1 4 diameter shank of a Grinding Accessory not included fully into the Col let 28 Then firmly re tighten the Collet Nut 29 to lock both the
8. in serious personal injury 8 Dress properly Do not wear loose clothing or jewelry Contain long hair Keep your hair clothing and gloves away from moving parts Loose clothes jewelry or long hair can be caught in moving parts 9 Avoid accidental starting Be sure the Trigger Lever 14 is off before connecting to the air supply Carrying pneumatic tools with your finger on the Trigger or connecting pneumatic tools to the air supply with the Trigger on invites accidents 10 Remove adjusting keys or wrenches before turning on the tool A wrench or a key that is left attached to a rotating part of the tool may result in personal injury 11 Do not overreach Keep proper footing and balance at all times Proper footing and balance enables better control and of the toll in unexpected situations 12 Use safety equipment Always wear ANSI approved safety glasses under neath a full face shield and hearing protection 13 Replacement parts and accessories When servicing use only identical replacement parts Use of any other parts will void the warranty Only use accessories intended for use with this tool Approved accessories are available from Harbor Freight Tools 14 Do not operate tool if under the influence of alcohol or drugs Read warning labels if taking prescription medicine to determine if your judgement or reflexes are impaired while taking drugs If there is any doubt do not operate the Wrench 15 Use proper size and t
9. ol Remove the Grinding Drum from the Die Grinder Then store the tool in a clean and dry location out of the reach of children Inspection Maintenance and Cleaning Warning Always make sure the Lever 14 is in its OFF position and disconnect the Die Grinder from its compressed air supply before performing any inspection adjustments maintenance or cleaning Before each use inspect the general condition of the Die Grinder Check for loose screws misalignment or binding of moving parts cracked or broken parts damaged air hose and any other condition that may affect its safe operation If abnormal noise or vibration occurs have the problem corrected before further use Never use damaged equipment Daily With a clean cloth remove all dirt oil and grease from the Die Grinder If neces sary you may use a mild detergent Do not use solvents as damage to the Die Grinder may occur Do not immerse the Die Grinder in any liquids SKU 95029 For technical questions please call 1 800 444 3353 Page 6 SKU 95029 Parts List and Diagram Part Description Q ty Plug Screw Air Regulator 7 1 Valve Spring Te 7 vaesem e fonn o moor Housing 8 Bah 20 Rotor o 21 25 27 29 30 NOTE Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts For technical questions please call 1 800 444 3353 Page Warranty AWA PAW A
10. on VD PLY verifies the defect we will either repair or replace the product at our election or we may elect to refund the purchase ZZA Z G price if we cannot readily and quickly provide you with a replacement We will return repaired products at our Wes AN expense but if we determine there is no defect or that the defect resulted from causes not within the scope of Ny gt our warranty then you must bear the cost of returning the product lt A ex KU This warranty gives you specific legal rights and you may also have other rights which vary from state to state a N A A 3491 Mission Oaks Blvd PO Box 6009 Camarillo CA 93011 800 444 3353 INXA A ANSE SS SS PO PO SO SO ASC SASSER SMSC SSCS SMCS SY PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER NOR DISTRIBU TOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INST
11. ype extension cord If an extension cord is required it must be of the proper size and type to supply the correct current to the compressor without heating up Otherwise the extension cord could melt and catch fire or cause electrical damage to the compressor Check your air compressor s manual for the appropriate size cord 16 Maintenance For your safety maintenance should be performed regularly by a qualified technician 17 Compressed air only Use clean dry regulated compressed air at 90 PSI Never use oxygen carbon dioxide combustible gases or any other bottled gas as a power source for this tool 18 When connecting to the air supply Prior to each use if an automatic oiler is not used add two drops of air tool oil not included into the Air Inlet 13 fitting of the Die Grinder 19 Always disconnect the Die Grinder from its compressed air supply source and squeeze the Trigger Lever 14 to release all compressed air in the tool before performing any maintenance or services Note Performance of the compressor if powered by line voltage may vary depending on variations in local line voltage Extension cord usage may also affect tool performance SKU 95029 For technical questions please call 1 800 444 3353 Page 3 20 Industrial applications must follow OSHA requirements Warning Some dust created by power sanding sawing grinding drilling and other construction activities contain chemicals known to the State o
Download Pdf Manuals
Related Search