Harbor Freight Tools 94585 User's Manual
Contents
1. A Wrap approximately 4 of Teflon tape around the male threads of a 1 4 NPT Quick Connector not provided Then wrench tighten the Quick Connector into the Air Inlet B If an automatic oiler is not used add two drops of oil into the Quick Connector C Turn on the compressor and set the regulator to the pressure recommended for this tool 90 PSI Quick Quick Quick Oiler Filter connector coupler cannector _ Air a i tre _ Air Drill T compressor Quick coupler Airline Oiler Assembly 3 ALWAYS DISCONNECT TOOL FROM ITS COMPRESSED AIR SUPPLY SOURCE BEFORE PERFORMING ANY SERVICES OR MAINTENANCE such as cleaning the tool changing chisels or punches moving to a different work location handing the tool to another person etcetera Caution After disconnecting the TOOL from the air compressor the TOOL will still be pressurized Point the TOOL onto an extra piece of work surface and depress the trigger until all pressure is released 4 MAINTAIN A SAFE WORK ENVIRONMENT Keep work area well lit Make sure there is adequate surrounding work space Use this product in a well ventilated area Do not operate this product in the presence of flammable liquids gasses or dust 5 DO NOT FORCE THE EQUIPMENT This product will do the work better and safer at the speed and capacity for which it was designed 6 AVOID UNINTENTIONAL STARTING Make sure you are prepared to begin work before depressing the Trigger 7 NEVER P2. KEEP WORK AREA CLEAN Cluttered damp or wet areas invite injuries KEEP CHILDREN AWAY Children must never be allowed in the work area Do not let them handle machines tools or hoses STORE IDLE EQUIPMENT When not in use tools must be locked up in a dry location to inhibit rust Always lock up tools and keep out of reach of children DO NOT FORCE THE TOOL It will do the job better and more safely at the rate for which it was intended Do not use inappropriate attachments in an attempt to exceed the tool s capacities USE THE RIGHT TOOL FOR THE JOB Do not attempt to force a small tool or attachment to do the work of a larger industrial tool Do not use a tool for a purpose for which it was not intended DRESS SAFELY Do not wear loose clothing or jewelry as they can be caught in moving parts Non skid footwear is recommended Wear restrictive hair covering to contain long hair USE EYE BREATHING AND EAR PROTECTION Wear ANSI approved impact safety goggles ANSI approved hearing protectors and ANSI approved dust mask or respirator when using this product ANSI approved safety impact eye glasses hearing protectors and dust masks and respirators are available from Harbor Freight Tools SKU 94585 For technical questions please call 1 800 444 3353 Page 2 8 DO NOT ABUSE THE POWER CORD Do not yank compressor s cord to disconnect it from the receptacle Do not carry tools by the cord 9 DO NOT OVERREACH Keep proper footing and
3. balance at all times Do not reach over or across running machines 10 MAINTAIN TOOLS WITH CARE Keep tools sharp and clean for better and safer performance Follow instructions for lubricating and changing accessories Inspect compressor s cord periodically and if damaged have them repaired by an authorized technician Inspect all hoses for leaks prior to use The handles must be kept clean dry and free from oil and grease at all times 11 REMOVE ADJUSTING KEYS AND WRENCHES Make it a habit to check that keys and adjusting wrenches are removed from the tool or machine work surface before plugging it in 12 AVOID UNINTENTIONAL STARTING Do not carry any tool with your finger on the trigger whether it is connected to the compressor or not 13 STAY ALERT Watch what you are doing use common sense Do not operate any tool when you are tired 14 CHECK DAMAGED PARTS Before using any tool any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function Check for alignment and binding of moving parts any broken parts or mounting fixtures and any other condition that may affect proper operation Any part that is damaged should be properly repaired or replaced by a qualified technician Do not use the tool if any switch does not turn on and off properly 15 REPLACEMENT PARTS AND ACCESSORIES When servicing use only identical replacement parts Use of any other par
4. in Figure 1 Motor Housing 16 Drill Chuck 2 Figure 1 Opening the Jaws Step 3 When the Jaws are open wide enough to insert the drill bit slide the bit into the DRILL CHUCK as far as possible SKU 94585 For technical questions please call 1 800 444 3353 Page 5 Step 4 By hand turn the DRILL CHUCK to tighten the Jaws as shown in Figure 2 Motor Housing 16 h Drill Chuck 2 Drill Bit Figure 2 Tightening the Jaws Step 5 Insert the Chuck Key into one of the three chuck holes in the DRILL CHUCK as shown in Figure 3 mating the teeth of the Chuck Key with the teeth of the DRILL CHUCK Drill Chuck 2 Chuck Hole Figure 3 Using the Chuck toTighten the Jaws Step 6 Turn the Chuck Key to tighten the Jaws Make sure the Jaws are tight Step 7 Put the Chuck Key in a safe place Do not lose the Chuck Key SKU 94585 For technical questions please call 1 800 444 3353 Page 6 Air Connection Step 1 Remove the plastic cap from the AIR INLET 29 Step 2 You will need a Union fitting sold separately before you can connect your Air Drill to an air compressor Attach the Union fitting to the AIR INLET Step 3 Attach an Air Coupler sold separately to the Union fitting if desired This is a useful accessory as it allows quick coupling action when using a variety of tools with the same air compressor Step 4 Your Air Drill is ready for use OPERATION Setup Frequent but no
5. CENTRAL PNEUMATIC W N 3 8 REVERSIBLE AIR DRILL Model 94585 Due to continuing improvement actual product may differ slightly from the product described herein ASSEMBLY and OPERATING sd OES Distributed Exclusively by 3491 Mission Oaks Blvd Camarillo CA 93011 Visit our Web Site at www harborfreight com Copyright 2006 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools For technical questions and replacement parts please call 1 800 444 3353 SPECIFICATIONS No Load Speed 1700 RPM Max Recommended Air Pressure 90 PSI Air Consumption 5 CFM Air Inlet 1 4 18 NPT Chuck Type 3 Jaw Keyed Chuck Chuck Size 3 8 Weight 2 4 lbs SAVE THIS MANUAL You will need the manual for the safety warnings and cautions assembly instructions operating procedures maintenance procedures trouble shooting parts list and diagram Keep your invoice with this manual Write the invoice number on the inside of the front cover Keep both this manual and your invoice in a safe dry place for future reference SAFETY WARNING amp CAUTIONS WARNING When using pneumatic equipment basic safety precautions should always be followed to reduce the risk of personal injury and hazards due to over pressurization READ ALL INSTRUCTIONS BEFORE USING THIS TOOL 1 2
6. OINT TOOL AT PEOPLE OR ANIMALS 8 WARNING Some dust created by power sanding sawing grinding drilling and other construction activities contain chemicals known to the State of California to cause cancer birth defects or other reproductive harm Some examples of these chemicals SKU 94585 For technical questions please call 1 800 444 3353 Page 4 Continued from page 4 are lead from lead based paints crystalline cilica from bricks and cement or other masonry products arsenic and chromium from chemically treated lumber Your risk from these exposures varies depending on how often you do this type of work To reduce your exposure to these chemicals work in a well ventilated area and work with approved safety equipment such as those dust masks that are specially designed to filter out microscopic particles California Health amp Safety Code 25249 5 et seq UNPACKING Your Air Drill comes completely assembled Included is a chuck key for use with this tool Check to make sure everything is included If any parts are missing or broken please call Harbor Freight Tools at the number on the cover of this manual ASSEMBLY Your Air Drill is completely assembled Follow the steps below to install drill bits and prepare for the operation of your Air Drill Drill Bit Installation Step 1 Select the drill bit needed for the drilling you wish to perform Step 2 Open up the Jaws of the Drill by turning the DRILL CHUCK 2 as shown
7. estions please call 1 800 444 3353 Page 11 WARRANTY PNEUMATIC LIMITED 1 YEAR Y WARRANTY Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of one year from the date of purchase This warranty does not apply to damage due directly or indirectly to misuse abuse negligence or accidents repairs or alterations outside our facilities or to lack of maintenance We shall in no event be liable for death injuries to persons or property or for incidental contingent special or consequential damages arising from the use of our product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS To take advantage of this warranty the product or part must be returned to us with transportation charges prepaid Proof of purchase date and an explanation of the complaint must accompany the merchandise If our VP Inspection verifies the defect we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement We will return repaired products at ou
8. n Points 29 PARTS LIST QTY Item Description ket cap screw 1 16 Motor Housing 1 17 Cup Point Set Screw 1 18 Trigger 1 19 Valve Spring 2 20 Reverse Valve 1 21 O Ring 3 22 Reverse Valve Bushing 1 23 Throttle Valve 1 24 O Ring 2 25 O Ring 2 26 Roll Pin 1 27 Exhaust Diffuser 5 28 Self Tapping 1 Button Head Screw 1 29 Air Inlet with Screen 30 Chuck Key Reverse Valve QTY i h h h i Se mere Ca Seer k h lt N NOTE Some parts are listed and shown for illustration purposes only and are not available iindividually as replacement parts SKU 94585 For technical questions please call 1 800 444 3353 Page 10 ASSEMBLY DIAGRAM DISCLAIMER PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THE ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYERASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACMENT PARTS THERETO SKU 94585 For technical qu
9. need to make Clamp the material in a vise to make sure the material does not move or begin to spin while drilling Wear eye protection to guard against flying wood or metal Set the compressor s pressure regulator to 90 PSI Do not set the compressor s outlet regulator over 90 PSI Connect the Air Drill to the air compressor s hose If leaking is detected disconnect the air hose and repair before use CAUTION Do not operate the Air Drill Grip the Air Drill firmly Place the drill bit on the spot mere siepi before placing the drill bit on the material To begin drilling press the TRIGGER 18 Your Air Drill has a variable speed for drilling To vary the speed of the drilling action vary the pressure on the TRIGGER Drill only as deep as necessary Do not drill deeper than necessary into walls or other areas where you cannot identify any possible hazards behind the drilling surface When you have drilled the hole remove the drill bit from the hole while the Air Drill is still spinning This is to prevent the drill getting caught in the hole and causing damage If the drill bit does get caught while you are drilling immediately release the TRIGGER WARNING Do not touch the DRILL CHUCK or the drill bit while the Air Drill is spinning SKU 94585 For technical questions please call 1 800 444 3353 Page 8 Step 12 Flip the REVERSE VALVE 20 to the R position as shown in Figure 5 This will rever
10. r expense but if we determine there is no defect or that the defect resulted from causes not within the scope of our warranty then you must bear the cost of returning the product This warranty gives you specific legal rights and you may also have other rights which vary from state to state 3491 Mission Oaks Blvd PO Box 6009 Camarillo CA 93011 800 444 3353 SINC ZS YC ZANE VANINA NI WIC IRN IC INCISIONS RS i A A SKU 94585 For technical questions please call 1 800 444 3353 Page 12
11. se the rotation of the drill allowing you to back out your drill bit Figure 5 Reversing the Rotation of the Drill Bit Step 13 Lightly press the TRIGGER until the drill bit spins free Remove the Air Drill Step 14 Flip the REVERSE VALVE back to the F position MAINTENANCE It is recommended that you use an Airline Oiler with your Air Drill If you do not use an Airline Oiler follow the steps below to maintain and prolong the life of your tool Step 1 Disconnect the Air Drill from the air hose CAUTION Do not use detergent oil or additives as these lubricants will Step 2 Apply a few drops of PNEUMATIC TOOL OIL through the air line before each use or every hour if used continuously cause accelerated wear to the Step 3 Apply a few drops of oil to the TRIGGER 18 seals in the tool Work the TRIGGER a few times to lubricate SKU 94585 For technical questions please call 1 800 444 3353 Page 9 Step 4 Twice a month apply a few drops of oil to the Jaws and REVERSE VALVE 24 as shown in Figure 6 Open and close the Jaws a few times to lubricate Jaws Item Description Flat head soc Drill Chuck Clamp Nut Flat Washer Ball Bearing Internal Gear Bearing Case 10 Ball Bearing 11 End Plate OONDAFRWNY gt gt 12 Rotor 13 Rotor Blade 14 Cylinder 15 Motor Alignment Pin l Trigger Planet Gear Carrier Planet Gear with Bushing 20 18 Air Inlet Figure 6 Lubricatio
12. t excessive lubrication is required for best performance Oil added through the airline connection will lubricate internal parts An automatic airline oiler is recommended but oil may be added manually before every operation or after about 1 hour of continuous use Only a few drops of oil at a time are necessary Too much oil will collect inside the tool and be blown out during the exhaust cycle ONLY USE PNEUMATIC TOOL OIL Do not use detergent oil or additives as these lubricants will cause accelerated wear to the seals in the tool Dirt and water in the air supply are major causes of pneumatic tool wear Use a filter oiler for better performance and longer life The filter must have adequate flow capacity for the specific application Consult the manufacturer s instructions for proper maintenance of your filter The connector on the tool must not hold pressure when the air supply is disconnected If the wrong fitting is used the tool can remain charged with air after being disconnected and still be able to drive a fastener See Airline Oiler Assembly on page 4 for the recommended accessories and connection order SKU 94585 For technical questions please call 1 800 444 3353 Page 7 Using The Air Drill Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 Step 8 Step 9 Step 10 Step 11 Mark the material you wish to drill at the spot for the hole Make sure your drill bit is the correct size for the hole you
13. ts will void the warranty Only use accessories intended for use with this tool Approved accessories are available from Harbor Freight Tools 16 DO NOT OPERATE TOOL IF UNDER THE INFLUENCE OF ALCOHOL OR DRUGS Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs If there is any doubt do not operate the tool 17 DRAIN THE COMPRESSOR USED TO POWER THE TOOL EVERY DAY Do not allow moisture to build up inside the compressor Do not allow compressor to sit pressurized for longer than one hour 18 MAKE SURE ALL EQUIPMENT IS RATED TO THE APPROPRIATE CAPACITY Make sure that regulator is set at least 10 PSI lower than the lowest rated piece of equipment you are using 19 MAINTAIN PRODUCT WITH CARE Keep clean and dry for better and safer performance 20 WARNING The warnings and precautions discussed in this manual cannot cover all possible conditions and situations that may occur It must be understood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator SKU 94585 For technical questions please call 1 800 444 3353 Page 3 SPECIFIC PRODUCT WARNINGS AND PRECAUTIONS 1 USE CLEAN DRY REGULATED COMPRESSED AIR AT 90 PSI Do not exceed the recommended 90 PSI Never use oxygen carbon dioxide combustible gases or any other bottled gas as a power source for this tool 2 WHEN CONNECTING TO THE AIR SUPPLY
Download Pdf Manuals
Related Search