Harbor Freight Tools 92043 User's Manual
Contents
1. AND OR DISTRIBUTOR EXPRESSLY STATES THat ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABIL ITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACE MENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACE MENT PARTS THERETO SKU 92043 For technical questions please call 1 800 444 3353 Page 42. intended to take the place of vehicle s normal back lighting system Warning The warnings cautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur It must be understood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator SKU 92043 For technical questions please call 1 800 444 3353 Page 2 Unpacking When unpacking check to make sure that all parts are included Refer to the Assembly Drawing and Parts List on the next page Installation During installation refer to the Assembly Drawing 1 Set the vehicle emergency brake and remove the ignition keys 2 Plug the vehicle s trailer brake light connector Flat 4 trailer plug into the Hitch Cover Brake Light Power Wire A5 plug If the vehicle does not have an existing trailer brake light cable installed have one installed by a qualified technician Note that the green wire on the Hitch Cover Brake Light is connected to the brake light cable of the vehicle The other wire is connected to ground or the chassis 3 Remove the Cotter Pin B2 from the Hitch Pin B1 Slide the Hitch Pin from the Hitch Cover Brake Light 4 With the Receiver Gasket in place against the Lens Housing A4 slide the Hitch Cover Brake Light into the hitch receiver 5 Insert the Hitch Pin B1 through the hole in the Hitch Cover Brake Light an
3. HITCH COVER WITH BRAKE LIGHT ASSEMBLY AND OPERATING INSTRUCTIONS SPECIFICATIONS Item Description Lens Polystyrene replaceable Light Source 12 bright red LED s Power Requirement 12 VDC Power Wire 16 AWG x 2C x 13 L inches Flat four trailer plug 4 pin slip fit Hitch Pin Hole Diameter 5 8 inch Dimensions 3 1 4 square x 4 3 8 D inches Hitch Receiver Depth Two inches on square hitch Weight 0 3 Ibs Receiver Gasket 1 2 inch thick Distributed Exclusively by HARBOR FREIGHT a oy os TOOLS tiie 3491 Mission Oaks Blvd Camarillo CA 93011 Visit our Web site at hitp www harborfreight com Copyright 2004 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools For technical questions and replacement parts please call 1 800 444 3353 Save This Manual You will need the manual for the safety warnings and precautions assembly instructions operating and maintenance procedures parts list and diagram Keep your invoice with this manual Write the invoice number on the inside of the front cover Keep the manual and invoice in a safe and dry place for future reference Safety Warnings and Precautions WARNING When using this product basic safety precautions should always be followed to reduce the risk of personal injur
4. d the hitch 6 Secure the Hitch Pin B1 by inserting the Cotter Pin B2 7 Test the Hitch Cover Brake Light by pressing down on the vehicle brake peddle Have another person view the Hitch Cover Brake Light 8 Remove and store the Hitch Cover Brake Light before attempting to attach a trailer to the vehicle hitch Maintenance 1 Periodically check that the Lens A1 is securely seated in the Lens Housing A4 2 Clean the Hitch Cover Brake Light with a cloth dampened with water Do not spray the brake light directly with a water hose 3 When not in use store the brake light in its original box to keep from scratching the lens SKU 92043 For technical questions please call 1 800 444 3353 Page 3 Parts List Part No Description Al Lens A2 LED Lights 12V 2W A3 Power Wire with Plug A4 Lens Housing A5 Receiver Gasket B1 Hitch Pin B2 Cotter Pin NOTE Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts Assembly Drawing PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER
5. y and damage to equipment Read all instructions before using this tool 1 Avoid working alone If an accident happens an assistant can bring help 2 Observe work area conditions Before installing the Hitch Cover Brake Light always set the vehicle emergency brake and remove the ignition key from the vehicle 3 Keep children away Children must never be allowed in the work area Do not let them handle machines tools or extension cords 4 Check for damaged parts Before using this product any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function Check for alignment and binding of moving parts any broken parts or mounting fixtures and any other condition that may affect proper operation Any part that is damaged should be properly repaired or replaced by a qualified technician 5 Replacement parts and accessories When servicing use only identical replacement parts Use of any other parts will void the warranty Only use accessories intended for use with this tool Approved accessories are available from Harbor Freight Tools 6 Do not operate a vehicle or install this product if under the influence of alcohol or drugs Read warning labels if taking prescription medicine to determine if your judgment or reflexes are impaired while taking drugs If there is any doubt do not operate 7 This product is intended to provide supplemental lighting and is not
Download Pdf Manuals
Related Search