Harbor Freight Tools 91851 User's Manual
Contents
1. A pees a j No Load Revolutions FIGURE C XXXX M N per Minute RPM SPECIFIC SAFETY RULES 1 This Camera is Rainproof however it is NOT intended for use as an underwater camera a Make sure to mount the Security Camera where it is protected from extreme weather and temperature conditions b Make sure to properly seal all connections from moisture c Do not immerse any part of this product in any liquid 2 Do not point the Security Camera at the sun or any other bright light source 3 Do not attempt to open the sealed parts of the Security Camera housing 4 The warnings precautions and instructions discussed in this manual cannot cover all possible conditions and situations that may occur The operator must understand that common sense and caution are factors which cannot be built into this product but must be supplied by the operator UNPACKING When unpacking check to make sure all the parts shown on the Parts List on page 10 are included If any parts are missing or broken please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible SKU 91851 For technical questions please call 1 800 444 3353 Page 7 ASSEMBLY AND OPERATING INSTRUCTIONS NOTE For additional information regarding the parts mentioned in the following pages refer to the Assembly Diagram on page 10 1 Locate the two mounting holes in the base of the Security Camera 1 Then use the two Wood Screws2. 4 to mount the Security Camera in the desired location on a wall or ceiling Then adjust the Security Camera to view a specific area See Figure D 2 Connect the Security Camera Phone Jack to the Cable 2 See Figure D 3 Connect the Audio Video Output Cables to your television NOTE The Yellow Cable connects to the Yellow video television jack The White Cable connects to the White audio television jack See Figure D 4 Plug the Adapter 3 into the nearest 120 volt grounded electrical outlet See Figure A 5 Turn on your television and set the channel selector to AV Channel The Secu rity Camera s view will then appear on the television screen Turn up the volume on the television and the Security Camera s built in microphone will relay sound to the television The video input selector may be a function of the TV remote control SECURITY TELEVISION CAMERA NOT INCLUDED 1 ADAPTER PHONE CABLE JACK 2 AUDIO VIDEO OUTPUT CABLES FIGURE D SKU 91851 For technical questions please call 1 800 444 3353 Page 8 INSPECTION MAINTENANCE AND CLEANING WARNING Always unplug the Adapter 3 from its electrical outlet prior to performing any inspection maintenance or cleaning procedures 2 Before each use inspect the general condition of the Security Camera Check for misalignment or binding of moving parts cracked or broken parts damaged wiring and any other condition that may a
3. ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO SKU 91851 For technical questions please call 1 800 444 3353 Page 10
4. RAINPROOF COLOR amp NIGHT VISION CAMERA SECURITY SYSTEM Model 91851 ASSEMBLY AND OPERATING INSTRUCTIONS Distributed Exclusively by 3491 Mission Oaks Blvd Camarillo CA 9301 1 Visit our Web site at http www harborfreight com Copyright 2004 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools For technical questions please call 1 800 444 3353 Extreme weather and temperature conditions excepted PRODUCT SPECIFICATIONS Po ttem Description Electrical Requirements Adapter Input 120 VAC 60 Hz 6 Watts Adapter Output 7 5 VDC 6 Long Adapter Power Cord w 2 Prong Plug 300K Pixels Color with Night Vision Operating Temperature Range 14 F 122 F 10 C 50 C Overall Dimensions 1 15 16 W x 3 3 4 L x 2 H Injection Molded Poly Plastic Additional Features Built In Microphone 80 AV Cable Rainproof Construction With the exception of extreme weather conditions Weight 1 75 Pounds SAVE THIS MANUAL You will need this manual for the safety warnings and precautions assembly oper ating inspection maintenance and cleaning procedures parts list and assembly diagram Keep your invoice with this manual Write the invoice number on the inside of the front cover Keep this manual and invoice in a safe and dry place for future ref
5. ccessories intended for this product SKU 91851 For technical questions please call 1 800 444 3353 Page 4 Improperly connecting the grounding wire can result in the risk of electric shock Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded Do not modify the power cord plug provided with the tool Never remove the grounding prong from the plug Do not use the tool if the power cord or plug is damaged If damaged have it repaired by a service facility before use If the plug will not fit the outlet have a proper outlet installed by a qualified electrician DOUBLE INSULATED TOOLS TOOLS WITH TWO PRONG PLUGS 1 The Adapter for the Security Camera is marked Double Insulated and does not require grounding The Adapter has a special double insulation system which satisfies OSHA requirements and complies with the applicable standards of Underwriters Laboratories Inc the Canadian Standard Association and the National Electrical Code See Figure A 2 Double insulated products may be used in either of the 120 volt outlets shown in the following illustration See Figure A FIGURE A SKU 91851 For technical questions please call 1 800 444 3353 Page 5 EXTENSION CORDS 1 Grounded tools require a three wire extension cord Double Insulated tools can use either a two or three wire extension cord 2 As the distance from the supply outlet increases you must use a heavi
6. er gauge extension cord Using extension cords with inadequately sized wire causes a serious drop in voltage resulting in loss of power and possible tool damage See Figure B 3 The smaller the gauge number of the wire the greater the capacity of the cord For example a 14 gauge cord can carry a higher current than a 16 gauge cord See Figure B 4 lf using more than one extension cord to make up the total length make sure each cord contains at least the minimum wire size required See Figure B 5 lf you are using one extension cord for more than one tool add the nameplate amperes and use the sum to determine the required minimum cord size See Figure B 6 lf you are using an extension cord outdoors make sure it is marked with the suffix suffix W A W in Canada to indicate it is acceptable for outdoor use re Make sure your extension cord is properly wired and in good electrical condition Always replace a damaged extension cord or have it repaired by a qualified electrician before using it RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS 120 VOLT NAMEPLATE EXTENSION CORD LENGTH AMPERES At Full Load Based on limiting the line voltage drop to five volts at 150 of the rated amperes FIGURE B SKU 91851 For technical questions please call 1 800 444 3353 Page 6 SYMBOLOGY By powe Insulated Q Canadian Standards Association Underwriters Laboratories Inc Vx foots Alternating Current
7. erence GENERAL SAFETY RULES A WARNING READ AND UNDERSTAND ALL INSTRUCTIONS Failure to follow all instructions listed below may result in electric shock fire and or serious injury SAVE THESE INSTRUCTIONS WORK AREA 1 Maintain a safe working environment Keep the work area well lit Make sure there is adequate surrounding workspace Always keep the work area free of obstructions grease oil trash and other debris Do not use the Security Cam era in areas near flammable chemicals dusts and vapors SKU 91851 For technical questions please call 1 800 444 3353 Page 2 ELECTRICAL SAFETY 2 Grounded tools must be plugged into an outlet properly installed and grounded in accordance with all codes and ordinances Never remove the grounding prong or modify the plug in any way Do not use any adapter plugs Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded If the tools should electrically malfunction or break down grounding provides a low resistance path to carry electricity away from the user 3 Double insulated tools are equipped with a polarized plug one blade is wider than the other This plug will fit in a polarized outlet only one way If the plug does not fit fully in the outlet reverse the plug If it still does not fit contact a qualified electrician to install a polarized outlet Do not change the plug in any way Double insulation O eliminates the need for the t
8. ffect its safe operation If a problem occurs with the Security Camera have the problem corrected before further use Do not use damaged equipment om To clean use a clean damp cloth to clean the outer surfaces of the Security Camera A mild detergent may be used Do not use solvents Do not immerse any part of the Security Camera in liquids 4 When storing always keep the Security Camera in the in a clean dry location SKU 91851 For technical questions please call 1 800 444 3353 Page 9 PARTS LIST AND ASSEMBLY DIAGRAM Part Description Qty Part Description _ Qty __ AC DC Adapter Cable 80 an 4 WOOD SCREWS NOT SHOWN NOTE Some parts are listed and shown for illustration purposes only and are not available individually as original or replacement parts PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE
9. hree wire grounded power cord and grounded power supply system 4 Do not abuse the Power Cord Never use the Power Cord to carry the Adapter or pull the Adapter from an outlet Keep the Power Cord away from heat oil sharp edges or moving parts Replace damaged Power Cords immediately Damaged Power Cords increase the risk of electric shock si When operating the Security Camera outside use an outdoor extension cord marked W A or W These extension cords are rated for outdoor use and reduce the risk of electric shock Also protect all connections from moisture PERSONAL SAFETY 6 Stay alert Watch what you are doing and use common sense when mounting the Security Camera Do not use power equipment while tired or under the influence of drugs alcohol or medication A moment of inattention may result in serious personal injury 7 Do not overreach when mounting the Security Camera Keep proper footing and balance at all times Proper footing and balance enables better control in unexpected situations 8 Wear eye protection when mounting the Security Camera Make sure to wear ANSI approved safety impact eye goggles Dust mask non skid safety shoes hard hat or hearing protection must be used for appropriate conditions SKU 91851 For technical questions please call 1 800 444 3353 Page 3 10 11 12 13 14 15 16 Les PRODUCT USE AND CARE Disconnect the Adapter from the power source before
10. making any adjust ments changing accessories or storing the Security Camera Such preven tive safety measures reduce the risk of accidents Mount the Security Camera so that it and its Cords are out of children s reach Maintain labels and nameplates on the Security Camera These carry important information If unreadable or missing contact Harbor Freight Tools for a replacement Maintain this product with care Keep this product clean and dry for better performance Maintenance For your safety service and maintenance should be performed regularly by a qualified technician Check for damaged parts Before using this product carefully check that it will operate properly and perform its intended function Check for damaged parts and any other conditions that may affect the safe operation of this product Re place or repair damaged or worn parts immediately Use the right product for the job Do not modify this product and do not use this product for a purpose for which it was not intended Tool service must be performed only by qualified repair personnel Service or maintenance performed by unqualified personnel could result in a risk of injury When servicing a tool use only identical replacement parts Follow in structions in the Inspection Maintenance And Cleaning section of this manual Use of unauthorized parts or failure to follow maintenance instructions may create a risk of electric shock or injury Only use a
Download Pdf Manuals
Related Search