Harbor Freight Tools 91091 User's Manual
Contents
1. to equipment Read all instructions before beginning assembly 1 Keep assembly area clean Cluttered areas invite injuries 2 Observe work area conditions Do not use machines or power tools in damp or wet locations Keep work area well lighted Do not use electrically powered tools in the presence of flammable gases or liquids 3 Keep children away Children must never be allowed in the assembly area Do not let them handle machines tools or extension cords 4 Do not exceed weight capacity of this chair To do so may cause personal injury or property damage 5 Use the right chair for the job Do not modify this chair and do not use this chair for a purpose for which it was not intended 6 Do not overreach Keep proper footing and balance during assembly 7 Stay alert Watch what you are doing use common sense during assembly and use of this chair SKU 91090 91091 Page 2 10 11 12 13 Use eye and ear protection Always wear ANSI approved impact safety goggles during assembly Wear a full face shield if you are producing wood chips Wear an ANSI approved dust mask or respirator when working around wood and chemical dusts and mists Take caution as some woods contain preservatives such as copper chromium arsenate CCA which can be toxic When cutting these materials extra care should be taken to avoid inhalation and minimize skin contact Check for damaged parts Before using this chair any part that appe2. weathering process This can be slowed by removing the chair from these conditions or covering it with a suitable cover You may wish to stain varnish or paint the chair If so follow the instructions supplied with these coatings Occasionally wash the chair with a garden hose or pressure sprayer to remove accumulated dust or dirt Wipe down or blow off any remaining water left on the chair after washing Periodically perhaps once per year recheck the tightness of all fasteners Normal usage of the chair and weathering of the wood may cause fasteners to loosen SKU 91090 91091 Page 4 Assembly Drawings TAS A l 4 Yi omae i PRA Hi I AEE Ly L Step 2 Attach C1 amp C2 with B using 6pcs of Attach B with 2pcs of D using 4pcs of bolts and nuts H to tighten up screw H to tighten up U a M i Attach E1 with C1 E2 with C2 using 4pcs Step 4 of Screw G to tighten up Then attach E1 Attach A with B and 2pcs of D using 6pcs and E2 with 2pcs of D using 2pcs of bolts of Screw G to tighten up and nuts I to tighten up COMPLETED Product secant L337 x W36 1 4 x H37 1 2 Attach F with C1 amp C2 using 4pcs of Screw G to tighten up SKU 91090 91091 Page 5 Parts List ir mame E ammine i frman Hidpes 1 2pes 55mm Bolt 65mm Bolt with Washer and Nut with Washer and Nut NOTE Some parts are listed and shown for illustration purposes only and are not ava
3. OneStopGardens M91090 M91091 WHITE PAINTED VARNISHED ADIRONDACK ADIRONDACK CHAIR CHAIR ASSEMBLY AND OPERATING INSTRUCTIONS Pi 3491 Mission Oaks Blvd Camarillo CA 93011 Visit our Web site at http www harborfreight com Copyright 2004 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools For technical questions and replacement parts please call 1 800 444 3353 Specifications SKU 91090 SKU 91091 Comfortable White Painted Fir Comfortable Varnished Fir wood Adirondack chair wood Adirondack chair Dimensions Overall 33 L x 36 W x 37 H Back Seat Height 10 Seat Area 18 1 2 D x 22 W Back Slat Length 32 Arm Rest 31 1 4 L x 5 1 8 W Front Legs 21 L x 3 W x 7 8 Front Seat Height 15 Side Legs 35 1 2 L Weight 20 Ibs Weight Capacity 250 Ibs Save This Manual You will need the manual for the safety warnings and precautions assembly instructions operating and maintenance procedures parts list and diagram Keep your invoice with this manual Write the invoice number on the inside of the front cover Keep the manual and invoice in a safe and dry place for future reference Safety Warnings and Precautions WARNING When assembling this item basic safety precautions should always be followed to reduce the risk of personal injury and damage
4. ars damaged should be carefully checked to determine that it will operate properly and perform its intended function Any part that is damaged should be properly repaired or replaced Replacement parts and accessories When servicing use only identical replacement parts Use of any other parts will void the warranty Only use accessories intended for use with this item Approved accessories are available from Harbor Freight Tools Do not assemble this chair if under the influence of alcohol or drugs Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs If there is any doubt do not proceed with assembly Maintenance For your safety service and maintenance should be performed regularly Check the alignment of all parts and check the tightness of all fasteners Warning The warnings cautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur It must be understood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator Unpacking When unpacking check to make sure the following parts are included 1 Back 1 Front Support 1 Seat 14 Wood Screws 2 Front Legs 10 55mm Bolts with nut and washer 2 Back Supports 2 65mm Bolts with nut and washer 2 Arms 1 Owner s Manual If any parts are missing or broken please call Harbor Freight Tools a
5. ilable individually as replacement parts PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THat ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO SKU 91090 91091 Page 6
6. t the number on the cover of this manual or contact your local Harbor Freight retailer SKU 91090 91091 Page 3 Assembly Carefully unpack the parts and check for damaged or missing parts Attach Left Front Leg C1 and Right Front Leg C2 to Seat B using 3 Bolts H per side Use the included washers and nuts to tighten Attach both Back Supports D to the inner sides of the Seat B using 2 Bolts H per side Tighten using the included washers and nuts Attach the Left Arm E1 and Right Arm E2 to the Front Legs C1 C2 using 2 Wood Screws G per side Attach the Arms E1 E2 to the Back Supports D using 1 Long Bolt I per side Tighten the bolts using included washers and nuts Attach the Back A to Seat B and Back Supports D using a total of 6 Wood Screws G Attach the Front Support F to the Front Legs C1 C2 using 2 Wood Screws G per side Recheck the alignment of all parts and recheck the tightness of all fasteners Set up the chair on a flat level location Do not exceed load capacity of 250 Ibs Maintenance This chair is made of natural Fir wood This beautiful material will naturally weather over time especially if used outdoors You can manage the speed and extent of this weathering by controlling the environment in which the chair is used and stored as well as any coatings you may apply Leaving the chair outside exposed to weather especially direct sun rain and salt air will soeed the
Download Pdf Manuals
Related Search