Home
Harbor Freight Tools 69243 User's Manual
Contents
1. injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death DANGER indicates a hazardous situation which if not avoided will result in death or serious injury AWARNING WARNING indicates a hazardous situation which if not avoided could result in death or serious injury ACAUTION CAUTION used with the safety alert symbol indicates a hazardous situation which if not avoided could result in minor or moderate injury NOTICE is used to address practices not related to personal injury CAUTION CAUTION without the safety alert symbol is used to address practices not related to personal injury General Safety Warnings WARNING Read all safety warnings and instructions Save all warnings and instructions for future reference 1 Avoid direct eye exposure The included laser enhancement glasses are NOT intended to protect your eyes in any way Page 2 10 11 12 13 14 15 For technical questions please call 1 800 444 3353 Do not direct the laser beam into the eyes of any person or animal Doing so may cause severe eye injury or death Verify Laser Level is in the Off position before making any adjustments or changing the batteries Position batteries in proper polarity and do not install batteries of different types charge levels or capacities together Remove batteries if Laser Level is not to be used for a long period of time The La
2. EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS To take advantage of this warranty the product or part must be returned to us with transportation charges prepaid Proof of purchase date and an explanation of the complaint must accompany the merchandise If our inspection verifies the defect we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement We will return repaired products at our expense but if we determine there is no defect or that the defect resulted from causes not within the scope of our warranty then you must bear the cost of returning the product This warranty gives you specific legal rights and you may also have other rights which vary from state to state PITTSBURGH 3491 Mission Oaks Blvd PO Box 6009 Camarillo CA 93011 800 444 3353
3. MENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO Parts List and Assembly Diagram e acustabe Handle e rack Seem O o laser window Record Product s Serial Number Here Note If product has no serial number record month and year of purchase instead Note Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts REV 07h SKU 69243 For technical questions please call 1 800 444 3353 Page 7 Limited 90 Day Warranty Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase This warranty does not apply to damage due directly or indirectly to misuse abuse negligence or accidents repairs or alterations outside our facilities criminal activity improper installation normal wear and tear or to lack of maintenance We shall in no event be liable for death injuries to persons or property or for incidental contingent special or consequential damages arising from the use of our product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES
4. PITTSBURGH Self leveling Laser Level Item 69243 AWARNING Read this material before using this product Failure to do so can result in serious injury SAVE THIS MANUAL When unpacking make sure that the product is intact and undamaged If any parts are missing or broken please call 1 800 444 3353 as soon as possible Visit our website at http www harborfreight com Email our technical support at tech harborfreight com Copyright 2011 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools Diagrams within this manual may not be drawn proportionally Due to continuing improvements actual product may differ slightly from the product described herein Tools required for assembly and service may not be included Save This Manual Keep this manual for the safety warnings and precautions assembly operating inspection maintenance and cleaning procedures Write the product s serial number in the back of the manual near the assembly diagram or month and year of purchase if product has no number Keep this manual and the receipt in a safe and dry place for future reference IMPORTANT SAFETY INFORMATION In this manual on the labeling and all other information provided with this product This is the safety alert symbol It is used to alert you to potential personal
5. Projects Up to 40 ft Lock Batteries 2 AA included To prevent serious injury and blindness Do not use included goggles for eye protection Read manual before use CDANGER gt Figure 1 LASER LIGHT AVOID DIRECT EYE EXPOSURE s i lt amW 8 Turnon the Laser Allow the laser lines to Wavelength 650 nm 10 GLASS Ila LASER PRODUCT stabilize for 4 to 6 seconds before starting This product complies with 21 CFR 1040 10 and 1040 11 any measuring or leveling tasks iode Mfr Sean amp Stephen Corp 4F NO3 Lane 335 Sec 4 Hsin Yi Rd Taipen China Manufacture Date i 11k 9 To disassemble and store move the pendulum lock to the left see Figure 1 and follow the above directions in reverse Assembly NOTICE If the pendulum lock is not engaged before movement the level may be damaged Read the ENTIRE IMPORTANT A SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product AWARNING TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION Turn Line Buttons off before adjusting Laser Level Note For additional information regarding the parts listed in the following pages refer to the Assembly Diagram near the end of this manual 1 Remove the tripod from the case 2 Open tripod s legs and adjust positioning of each leg until base is level Use bubble level in tripod base as a guide w Remove the Laser Level
6. Y FROM ACCIDENTAL OPERATION Turn Line Buttons off before performing any inspection maintenance or cleaning procedures TO PREVENT SERIOUS INJURY FROM TOOL FAILURE Do not use damaged equipment If abnormal noise or vibration occurs have the problem corrected before further use Installing and Removing Batteries 1 Remove the Battery Cover see Figure 2 on page 4 and insert two new AA Batteries Follow the polarity symbols so that the positive and negative ends of the batteries match the diagram 2 WARNING Do not mix old and new batteries Remove batteries when storing Laser Replacement Parts NOTE Internal replacement parts are not available for this item Cleaning and Maintenance 1 BEFORE EACH USE inspect the general condition Laser Level Check for loose hardware misalignment or binding of moving parts cracked or broken parts and any other condition that may affect its safe operation 2 AFTER USE wipe external surfaces of the tool with clean cloth 3 Store the Laser Level indoors and out of children s reach REV 07h SKU 69243 Level Beam Accuracy 1 For technical questions please call 1 800 444 3353 Set up the instrument with the Tripod centered between two walls approximately 16 ft apart Ensure the Rotary Base is level Push the Pendulum Lock to the right to free the pendulum See Figure 1 on page 3 Press both the horizontal and vertical buttons to project a laser cr
7. from the case gt Install batteries making sure to align batteries according to indicated polarity 5 Attach the Laser to the tripod base Do this by threading the bolt at the top of the tripod through the holes at the center of the Laser Level s lower base 6 Level the Laser by using the tri brack adjustment screws until the bubbles are centered on the two levels REV 10k SKU 69243 For technical questions please call 1 800 444 3353 Page 3 4 Press the button for the desired line s on Operating Instructions the top of the unit to switch ON Read the ENTIRE IMPORTANT A SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product AWARNING TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION Turn Line Buttons off before adjusting Level 1 After removing the Laser from the Carrying Case open the battery compartment insert the Vertical Horizontal two AA Batteries into the battery compartment Line Button Line Button according to the polarity symbols shown inside Figure 3 and close the battery compartment door 2 Be sure to set the Laser on as flat a surface as s The Laser Level will wark properly ee possible The tri brack adjustment on the base pasmane Witte SeMeveig range of the level can be used to help level the unit 6 Allow 4 6 seconds for the horizontal Turn each of the knobs to either raise or and vertica
8. l Laser lines to be stabilized lower that corner The self leveling range of After stabilization the Laser lines can be used for the Laser is within 6 Use the 2 Vials on measurement reference Laser lines may swing the base to verify that the base is level slightly due to vibration from surroundings 7 To prevent damage to the level tighten the pendulum lock see Figure 1 on page 3 after use and store in the carrying case NOTICE If the pendulum lock is not engaged Battery before movement the level may be damaged Compartment Aste pening After Using Laser Pendulum Lock 1 Detach Laser from Tripod hidden 2 Switch off both laser lines horizontal and vertical Check to see that both indicator LED s are off Vial Tri brack 3 Engage Pendulum Lock by moving it to the left one corner See Figure 1 on page 3 After use the Pendulum Lock should be locked before the instrument is put away in the Carrying Case Figure 2 3 Push the Pendulum Lock to the right to free the pendulum See Figure 1 on page 3 REV 05c 05g 07h Page 4 For technical questions please call 1 800 444 3353 SKU 69243 Maintenance and Servicing Accuracy Checking NOTE Due to the complicated sensitive nature of these procedures ordinarily only a qualified technician would attempt them Procedures not specifically explained in this manual must be performed only by a qualified technician A AWARNING TO PREVENT SERIOUS INJUR
9. ment until the vertical beam The length of the string should be 16 ft has moved 16 ft to the right side and mark b 8 ft from the intersection of the beams to the 4 Mark M1 16 ft from point A on the string thon Bie Bonzouial lhe See Figiie 5 Mark M2 8 ft below the intersection of the beams on the vertical line 6 Measure the distance between M1 and M2 7 Ifthe distance is less than or equal to 2 mm the accuracy is within tolerance Otherwise take the instrument to a qualified technician for repair Figure 6 5 Ifthe distance between a and b is less than or equal to 2mm the accuracy is within tolerance Otherwise take the instrument to a qualified technician for repair Page 6 For technical questions please call 1 800 444 3353 SKU 69243 PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACE
10. oss on wall A Mark point a4 at the intersection of the beams Turn the cross line laser 180 and repeat on wall B marking point b4 at the intersection of the beams see Figure 4 A Figure 4 Move the instrument straight towards wall A to a point 2 ft away and repeat step 2 marking the intersections as ag and bg see Figure 5 2 14 Figure 5 a distance da a4 ag b distance dp b4 b2 If da dp lt 1mm the accuracy is within tolerance Otherwise return the instrument to a qualified technician for repair Page 5 Horizontal Beam Level Accuracy Vertical Beam Level Accuracy End to End End to End 1 Set up the instrument with the Tripod 1 Set up the instrument with the Tripod approximately approximately 16 ft from the wall The wall 16 ft from the wall Ensure the Rotary Base is level should be at least 17 ft high Please ensure the Rotary Base is approximately level 2 Push the Pendulum Lock to the right to free the pendulum See Figure 1 on page 3 2 Press both the horizontal and vertical buttons to project a laser cross on the wall 3 Press both the horizontal and vertical buttons mark point A 8 ft above the intersection to project a laser cross on the wall mark point of the beams on the vertical beam a 8 ft from the intersection of the beams to the right on the horizontal beam 3 Use Aas a starting point and nail one end of a string with plumb bob not included on A 4 Turn the instru
11. ser Level is a delicate instrument do not drop or jar the Laser Level Keep work area clean and well lit This product is not a toy Keep it out of reach of children Keep children and bystanders away while operating Laser Level Inspect before every use do not use if parts loose or damaged Stay alert watch what you are doing and use common sense when operating Laser Level Do not use Laser Level while you are tired or under the influence of drugs alcohol or medication Dress properly Do not wear loose clothing or jewelry Keep your hair clothing and gloves away from moving parts Maintain labels and nameplates on the tool These carry important safety information If unreadable or missing contact Harbor Freight Tools for a replacement WARNING This product contains or when used produces a chemical known to the State of California to cause cancer and birth defects or other reproductive harm California Health amp Safety Code 25249 5 et seq The warnings precautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur It must be understood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator SAVE THESE INSTRUCTIONS Rev 05c 06b SKU 69243 7 Push the Pendulum Lock to the right to Specifications free the pendulum See Figure 1 Pendulum
Download Pdf Manuals
Related Search
Related Contents
Guida alla protezione delle colture ornamentali Téléchargez notre fiche conseil Manual - General Tools And Instruments 70055, 70056, 70065 & 70066 - Victor Jr Series intext:Betriebsanleitung filetype:pdf MANUAL DE INSTRUCCIONES manuale di istruzioni - Evolution Power Tools BENDIX BW1554 User's Manual Panasonic WJ-HD220 Specification Sheet Copyright © All rights reserved.
Failed to retrieve file