Harbor Freight Tools 5 in. Rugged Cast Iron Drill Press Milling Vise Product manual
Contents
1. A NE Mon R ey A hha EA Le a es a n i N Middle Base Screw 10 Vise Adjustment Screw 8 Figure 2 Page 4 For technical questions please call 1 800 444 3353 Item 69159 2 Turn the Handles on the Vise Jaw Screws 19 to hold the workpiece in place The unit is calibrated to eight turns per inch 1 8 per turn Match up with the visual aid reference scales SAE which are located on all four sides of the Vise See Figures 3 amp 4 Visual Aid Reference Scales Figure 4 Handle Handle Figure 3 3 The opposing adjustable jaws enable the work piece to be firmly secured yet located in the middle of the X Y movement 4 To prevent accidents clean when finished then store the tool indoors out of children s reach Item 69159 For technical questions please call 1 800 444 3353 Page 5 Maintenance and Servicing Procedures not specifically explained in this manual must be performed only by a qualified technician CAUTION TO PREVENT INJURY FROM TOOL FAILURE Do not use damaged equipment If damaged or loose parts are noted have the problem corrected before further use 1 BEFORE EACH USE inspect the general 4 Check and tighten the mounting screws condition of the tool Check for loose to be sure the Vise is secure hardware misalignment or binding of moving parts cracked or broken parts and any other 5 Replacing a Jaw Plate 2 condition that may affect its safe operation a2. Unscrew the Screws holding the Jaw and set aside 2 AFTER USE wipe external surfaces of the tool with clean cloth b Replace with a new Jaw and securing in place with the Screws Tighten 3 Keep the moving parts oiled being sure to wipe c Repeat on the other Jaws if off any excess oil off of the Handle and Jaws necessary See Figure 6 Jaw Plate 2 Page 6 For technical questions please call 1 800 444 3353 Item 69159 Parts List and Diagram PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO 6 Flat Head Screw 1 4 20 x 3 8 L 8 ViseAdjustment Screw 9 NutBlock o O o Hex Screw 1 4 20 x 5 8 L Record Product s Serial Number Here Note If product has no serial number
3. our inspection verifies the defect we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement We will return repaired products at our expense but if we determine there is no defect or that the defect resulted from causes not within the scope of our warranty then you must bear the cost of returning the product This warranty gives you specific legal rights and you may also have other rights which vary from state to state Forge 3491 Mission Oaks Blvd PO Box 6009 Camarillo CA 93011 800 444 3353
4. record month and year of purchase instead Note Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts Item 69159 For technical questions please call 1 800 444 3353 Page 7 Limited 90 Day Warranty Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase This warranty does not apply to damage due directly or indirectly to misuse abuse negligence or accidents repairs or alterations outside our facilities criminal activity improper installation normal wear and tear or to lack of maintenance We shall in no event be liable for death injuries to persons or property or for incidental contingent special or consequential damages arising from the use of our product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS To take advantage of this warranty the product or part must be returned to us with transportation charges prepaid Proof of purchase date and an explanation of the complaint must accompany the merchandise If
5. the equipment you will mount this vise on Dress properly Do not wear loose clothing or jewelry Keep your hair clothing and gloves away from moving parts Loose clothes jewelry or long hair can be caught in moving parts Do not force the tool Use the correct tool for your application The correct tool will do the job better and safer at the rate for which it was designed Make sure that the equipment s bit does not come in contact with this vise Damage to the vise may damage the workpiece or cause a piece to fly off causing personal injury This product is not a toy Keep it out of reach of children Maintain labels and nameplates on the tool These carry important safety information If unreadable or missing contact Harbor Freight Tools for a replacement A SAVE THESE INSTRUCTIONS Page 2 For technical questions please call 1 800 444 3353 Item 69159 Specifications 4 3 4 7 1 8 6 1 8 56 Square Inch X and Y Movement Calibrated to Scales Setup Before Use Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product Note For additional information regarding the parts listed in the following pages refer to Parts List and Diagram on page 7 Assembly Mounting 1 Make sure the power head of your drill press 2 Secure the Lower Base 1 of the Vise in the center is fastened securely to th
6. ORMATION AWARNING Read all safety warnings and instructions Failure to follow the warnings and instructions may result in serious injury Save all warnings and instructions for future reference Setup Safety 1 Mount this item securely before use The forces exerted on this vise during use may cause a poorly mounted or unmounted vise or workpiece to come loose causing SEVERE PERSONAL INJURY or property damage Operation Safety 1 Stay alert watch what you are doing and use common sense when operating a tool Do not use while you are tired or under the influence of drugs alcohol or medication A moment of inattention may result in serious personal injury Use personal protective equipment Always wear ANSl approved safety goggles Safety equipment used for appropriate conditions will reduce personal injuries Maintenance and Storage Safety 1 Store idle tools out of the reach of children and do not allow persons unfamiliar with the tool or these instructions to operate the power tool Power tools are dangerous in the hands of untrained users Maintain tools Check for misalignment or binding of moving parts breakage of parts and any other condition that may affect the tool s operation If damaged have the tool repaired before use Many accidents are caused by poorly maintained tools Carefully follow all warnings and operation instructions including accessory mounting instructions provided with
7. Owner s Manual amp Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions assembly operating inspection maintenance and cleaning procedures Write the product s serial number in the back of the manual near the assembly diagram or month and year of purchase if product has no number Keep this manual and the receipt in a safe and dry place for future reference ITEM 69159 RUGGED CAST IRON DRILL PRESS MILLING VIS W AAN E p ANA A _ lt we NONY o eT i l Re aks ee A SET PE a a v y i Visit our website at http www harborfreight com Email our technical support at tech harborfreight com When unpacking make sure that the product is intact and undamaged If any parts are missing or broken AWARNING please call 1 800 444 3353 as soon as possible Copyright 2011 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in Read this material before using this product any shape or form without the express written consent of Harbor Freight Tools Failure to do so can result in serious injury Diagrams within this manual may not be drawn proportionally Due to continuing SAVE THIS MANUAL improvements actual product may differ slightly from the product described herein Tools required for assembly and service may not be included IMPORTANT SAFETY INF
8. e column of the drill of the drill press worktable using appropriate press Lock the worktable into place hardware as provided with or explained in the manual for the drill press machine hardware not included Make sure that the hardware used solidly secures the vise and does not interfere with the X Y adjustment of the vise See Figure 1 Functions Upper Base Screw 17 gt lt _ Vise Jaw Screw 19 CA u Upper Base 18 Se l Vise Jaws A S amp Lz A Middle Base 14 Vise Adjustment A A screw 8 fy u y ZS we ee Middle Base Screw 10 Vise Adjustment Screw 8 Lower Base 1 Figure 1 Vise Jaw Screw 19 ltem 69159 For technical questions please call 1 800 444 3353 Page 3 Operating Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product Work Piece and Work Area Set Up Designate a work area that is clean and well lit The work area must not allow access by children or pets to prevent distraction and injury General Operating Instructions 1 The Vise Adjustment Screws 8 and Middle Base Screw 10 are for adjusting the tension on X Y movement of the workpiece secured in the Vise Jaws Use the handles to hold the Adjustment Screws 8 amp 10 at the desired tension See Figure 2 and Parts Diagram page 7 Vise Adjustment Screw 8
Download Pdf Manuals
Related Search