Harbor Freight Tools 46908 User's Manual
Contents
1. MINI OFF ROAD FOG LIGHTS Model 46908 OPERATING INFORMATION Distributed Exclusively by 3491 Mission Oaks Blvd Camarillo CA 93011 Visit our Web site at http www harborfreight com Copyright 2002 by Harbor Freight Tools All rights reserved No portion of this Prod uct Information Sheet or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools For technical questions please call 1 800 444 3353 SPECIFICATIONS TABLE Electrical Requirements Halogen H3 Type Lamp 12 Volt DC 55 Watt 15 Amp In Line Glass Fuse Power Switch Rocker T pe i Glass Oval 4 1 4 L x 1 7 8 H Blue Glow Dichromatic Sheet Strap Steel Glass Lens Weight 1 20 Pounds Lamp Dimensions SAVE THIS MANUAL You will need this Product Information Manual for the safety warnings and pre cautions assembly inspection maintenance and cleaning procedures Keep your invoice with this Product Information Manual Write the invoice number on the front page Keep this Product Information Manual and invoice in a safe and dry place for future reference GENERAL SAFETY WARNINGS AND PRECAUTIONS 1 KEEP WORK AREA CLEAN AND DRY Cluttered damp or wet work areas invite injuries 2 KEEP CHILDREN AWAY FROM WORK AREA Do not allow children to handle this product 3 STORE IDLE EQUIPMENT When not in use tools and equipment should be stored in a dr2. UYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO SKU 46908 PAGE 6
3. ditional references to the parts mentioned below refer to Figure A he Wiri r is M I 1 To mount the Mini Off Road Fog Lights select the desired mounting locations on the vehicle typically the front grill area 2 Position the Main Bracket on the underside of the vehicle s surface where the Mini Off Road Fog Light will be mounted See Figure A next page 3 Slide the U Shaped Support Bracket over the topside of the vehicle s mounting surface and underside of the Main Bracket See Figure A next page 4 Secure the Main Bracket and U Shaped Support Bracket to the vehicle s mount ing surface using the two Vertical Bolts See Figure A next page 5 Position the Lens and Lamp with pre attached Horizontal Bolts between the flanges of the Main Bracket and secure the Lens and Lamp to the Main Bracket with the two Nuts See Figure A next page 6 For wiring instructions refer to the Wiring Diagram on the last page of this Manual SKU 46908 PAGE 4 VEHICLE VERTICAL SURFACE U SHAPED SUPPORT BRACKET MAIN BRACKET LENS amp LAMP HORIZONTAL BOLT FIGURE A INSPECTION MAINTENANCE AND CLEANING 1 Caution To avoid electrical shock always disconnect both Battery Cables from the vehicle s Battery prior to performing inspection maintenance and cleaning 2 Before each use inspect the general condition of the Mini Off Road Fog Lights Check for cracks or breaks in the Lens loose or broken Wiring d
4. efective Halo gen Lamps loose or broken Mounting Brackets and any other condition that may affect safe operation If a problem occurs with the Mini Off Road Fog Lights immediately discontinue their use and have the problem corrected before further use Do not use damaged equipment 3 To replace the Halogen Lamps remove the Lamp Socket and replace only with new 12 Volt DC 55 Watt Halogen H3 type Lamps NOTE Though only one Lamp at a time may burn out it is recommended to replace both Lamps at the same time 4 To clean the Lens wipe with a damp cloth You may use a mild detergent Do not use solvents de greasers or other harsh chemicals as damage to the Lens may occur SKU 46908 PAGE 5 WIRING DIAGRAM 15A FUSE RED BLACK BLACK WHITE NOTE Some parts are shown for illustration purposes only No replacement parts are available for this product PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THIS ASSEMBLY INFORMATION MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALI FIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CEATIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE B
5. tenance should be performed regularly by a qualified technician USE THE RIGHT PRODUCT FOR THE RIGHT JOB There are certain applications for which this product was designed Do not use this product for a purpose for which it was not intended WARNING The warnings and precautions discussed in this manual cannot cover all possible conditions and situations that may occur The operator must understand that common sense and caution are factors that cannot be built into this product but must be supplied by the operator SPECIFIC PRODUCT WARNINGS AND PRECAUTIONS PRIOR TO INSTALLING THIS PRODUCT ON A VEHICLE MAKE SURE TO READ AND UNDERSTAND ALL INSTRUCTIONS AND SAFETY PRECAU TIONS AS OUTLINED IN THE VEHICLE MANUFACTURER S MANUAL TO AVOID ELECTRICAL SHOCK ALWAYS DISCONNECT BOTH BATTERY CABLES FROM THE VEHICLE S BATTERY PRIOR TO PRODUCT INSTALLA TION INSPECTION MAINTENANCE AND CLEANING SKU 46908 PAGE 3 3 ALWAYS WEAR CLEAN CLOTH GLOVES WHEN INSTALLING AND RE PLACING THE HALOGEN LAMPS Moisture dirt grease oil and other foreign materials introduced on the surface of the Halogen Lamps will damage and or reduce the life of the Lamps UNPACKING When unpacking check to make sure the parts shown on Figure A and the Wiring Diagram are included if any parts are missing or broken please call Harbor Freight Tools at the number shown on the front page of this Manual as soon as possible ASSEMBLY INSTRUCTIONS NOTE For ad
6. y location to inhibit rust Always lock up tools and equipment and keep out of reach of children 4 DO NOT USE TOOLS IF UNDER THE INFLUENCE OF ALCOHOL OR DRUGS Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs If there is any doubt do not attempt to use tools 5 USE EYE PROTECTION Wear ANSI approved safety impact eyeglasses when installing this product ANSI approved safety impact eyeglasses are available from Harbor Freight Tools SKU 46908 PAGE 2 10 11 14 INDUSTRIAL APPLICATIONS MUST FOLLOW OSHA REQUIREMENTS DO NOT OVERREACH Keep proper footing and balance at all times to prevent tripping falling back injury etcetera STAY ALERT Watch what you are doing at all times Use common sense Do not use tools when you are tired or distracted from the job at hand CHECK FOR DAMAGED PARTS Before using this product carefully check that it will operate properly and perform its intended function Check for damaged parts and any other conditions that may affect the operation of this product Replace or repair damaged or worn parts immediately REPLACEMENT PARTS AND ACCESSORIES When servicing use only identical replacement parts Only use accessories intended for use with this product Approved accessories are available from Harbor Freight Tools MAINTAIN THIS PRODUCT WITH CARE Keep this product clean MAINTENANCE For your safety service and main
Download Pdf Manuals
Related Search