Harbor Freight Tools 450 lb. Low Lift Transmission Jack Product manual
Contents
1. Item 61232 For technical questions please call 1 800 444 3353 Page 3 Ratchet Tie Down 31 Ratchet Handle Assembly Saddle 30 Screw Rod 20 PITTSBURGH EEE Page 4 For technical questions please call 1 800 444 3353 ltem 61232 A Removing a Transmission 1 Once the vehicle is raised and secured on a lift clear the area underneath the vehicle of people and tools 2 Roll the Jack under the transmission 3 Engage a 1 2 Drive Ratchet or Breaker Bar neither one included in the square Socket in the Screw Rod Rotate the Screw Rod clockwise Raise the Jack until the Saddle nearly contacts the underside of the transmission 4 Position the Jack directly under the center of gravity of the transmission Assure a good contact between the Saddle and the transmission The transmission must be properly supported and balanced when removed from the vehicle and resting on the Jack 5 Loosen the Wing Nuts Rotate the Screw Rod clockwise and raise the Jack further until the Saddle presses slightly against the transmission 6 To secure the transmission to the Saddle pass the Ratchet Tie Down over the top of the transmission and secure it See Ratchet Tie Down Operation below Ratchet Tie Down Operation The Ratchet Tie Down secures the transmission to the Jack to prevent the transmission from falling Securing the Ratchet Tie Down To secure the transmission to the Jack first pass the Strap over the top of2. PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO Record Product s Serial Number Here Note If product has no serial number record month and year of purchase instead Note Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts Page 6 For technical questions please call 1 800 444 3353 Item 61232 Parts List and Diagram Part Description Qty Part Description Qty Part Description Qty 13 Pin 6 Bushing 8 Wheel _ _ 9 Adjustable Frame 2 so Let Part 2 LZ Saddle 1 Ratchet Tie Down 1 Retaining Clip Item 61232 For technical questions please call 1 800 444 3353 Page Limited 90 Day Warranty Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase This warranty does not apply to damage due directly or indirectly to misuse ab
3. the transmission The Strap must not twist or press on any part of the transmission that might be damaged such as the speedometer cable fitting 1 Pass the free end of the Strap through the Ratchet Tie Down behind the Reel then through the Slot in the Reel See Figure C Figure C Ratchet Tie Down Use 2 Tighten the Strap by pressing the Ratchet Handle down repeatedly Check that the Strap and Ratchet Tie Down are securely fastened before continuing Item 61232 For technical questions please call 1 800 444 3353 Read ENTIRE IMPORTANT SAFETY INFORMATION section at beginning of this manual including all text under subheadings therein before set up or use of this product 7 Check that the Ratchet Tie Down is tight and the transmission is secure on the Saddle Tighten the Wing Nuts and raise the Jack until the transmission s weight is supported by it 8 Remove bolts and fittings attaching the transmission to the vehicle as recommended by the vehicle s repair instructions 9 Turn the Screw Rod counterclockwise slowly and lower transmission slightly Recheck that the transmission is secure and firmly strapped to the Saddle Make any necessary adjustments 10 When it is safe lower the transmission fully by turning the Screw Rod counterclockwise For safety two people should be working together to perform these operations 11 Stabilize the transmission on the Jack and roll the Jack from under the vehicle to the re
4. 53
5. Owner s Manual amp Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions assembly operating inspection maintenance and cleaning procedures Write the product s serial number in the back of the manual near the assembly diagram or month and year of purchase if product has no number Keep this manual and the receipt in a safe and dry place for future reference PITTSB URGH CR ITEM 61232 450 Lb Low Lift Transmission Jack Note This tool requires a 1 2 drive ratchet or breaker bar to operate neither one included Visit our website at http www harborfreight com Email our technical support at tech harborfreight com When unpacking make sure that the product is intact and undamaged If any parts are missing or broken please call 1 800 444 3353 as soon as possible Copyright 2013 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in Read this material before using this product any shape or form without the express written consent of Harbor Freight Tools Failure to do so can result in serious injury Diagrams within this manual may not be drawn proportionally Due to continuing SAVE THIS MANUAL improvements actual product may differ slightly from the product described herein Tools required for assembly and service may not be included Specifications Maximum Load Capacity 450 Ibs Saddle
6. ar the area near the Jack Turn the Screw Rod counterclockwise to lower the Jack Move the Jack clear of the vehicle Maintenance TO PREVENT SERIOUS INJURY FROM TOOL FAILURE Procedures not specifically explained in this manual must A be performed only by a qualified technician AWARNING Do not use damaged equipment If abnormal noise or vibration occurs have the problem corrected before further use 1 BEFORE EACH USE inspect the general condition of the equipment Check for loose hardware misalignment or binding of moving parts visibly leaking hydraulic fluid cracked or broken parts and any other condition that may affect its safe operation 2 Before each use and after the inspection thoroughly test the Jack for proper operation prior to its actual use Occasionally lubricate the mechanical parts of the Jack such as the Screw Rod and hinge pins of the Adjustable Frame with heavy oil or grease Wipe dry with a clean cloth Then store the Jack in a safe dry location out of reach of children and other non authorized people PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY
7. ing use 5 Use of this product is limited to the removal installation and transportation in the lowered position of transmissions transfer cases and transaxles 13 The brass components of this product contain lead 7 Keep clear of load while lifting and lowering a chemical known to the State of California to cause cancer birth defects or other reproductive harm 8 Lower load slowly California Health amp Safety Code 25249 5 et seq 9 Do not use for aircraft purposes 14 Store idle equipment When not in use tools must be stored in a dry location to inhibit rust Always lock up tools and keep out of reach of children A SAVE THESE INSTRUCTIONS Page 2 For technical questions please call 1 800 444 3353 Item 61232 Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product TO PREVENT SERIOUS INJURY AWARN NG Remove load from the jack before any procedure on this page Note For additional information regarding the parts listed in the following pages refer to Parts List and Diagram on page 7 1 Locate set of four Casters 2 four M12 Nuts 4 and four M12 Washers 3 M12 Nut 4 2 Inserta Caster in each opening in Base 1 3 Place a Washer 3 and Nut 4 over the threaded end of each Caster Assembly Tighten securely See Figure A Figure A Caster Assembly PITTSBURGH EEE
8. pair work location Have an assistant help to lower and move the transmission 3 Removing the Ratchet Tie Down When preparing to remove the Ratchet Tie Down have an assistant stabilize the transmission on the Jack to prevent it from falling 4 Toremove the Strap pull release tab A away from the spool Swing the upper Handle wide open The Handle should rest on the raised portion of the flanges See Figure D Release TabA Release Tab B Figure D Releasing the Strap CAUTION Keep your fingers clear of the spool when releasing the Ratchet it will rotate as the strap is released 5 When the Strap is loose pull the end free Remove the Strap from its position around the transmission Have an assistant stabilize the transmission safely Page 5 Replacing a Transmission 1 Check that the transmission is balanced on the Saddle and that the Ratchet Tie Down is securing the load on the Jack Check that the Wing Nuts are tight Move the Jack to line up the transmission properly with its connection points Have an assistant stabilize the load while moving the Jack Use a 1 2 Drive Ratchet or Breaker Bar neither one included to turn the Screw Rod clockwise Slowly and gradually raise the Jack while guiding it into place Secure the transmission into place using its hardware Double check all work to be sure the transmission is securely installed Release the Ratchet Tie Down and remove it Cle
9. tilt Maximum height 23 1 4 Cradle size 6 7 8 x 13 Minimum height 7 1 4 WARNING SYMBOLS AND DEFINITIONS This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death lt a a ae eee eee eee CAUTION IMPORTANT SAFETY INFORMATION AWARNING Read all safety warnings and instructions Save all warnings and instructions for future reference Failure to heed these markings may result in personal injury and or property damage Addresses practices not related to personal injury 1 Study understand and follow all instructions 10 Inspect before every use do not use before operating this device if parts are loose or damaged 2 Do not exceed 450 Ib rated capacity 11 Do not alter the jack or use attachments and or adapters that are not supplied by the manufacturer 3 Use only on hard level surfaces This tool requires a 1 2 Drive Ratchet or Breaker Bar to operate neither one included Adequately support the vehicle before starting repairs 12 The warnings precautions and instructions discussed in this manual cannot cover all possible conditions and situations that may occur The operator must understand that common sense and caution are factors which cannot be built into 6 Wear ANSI approved safety goggles and this product but must be supplied by the operator heavy duty work gloves dur
10. use negligence or accidents repairs or alterations outside our facilities criminal activity improper installation normal wear and tear or to lack of maintenance We shall in no event be liable for death injuries to persons or property or for incidental contingent special or consequential damages arising from the use of our product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS To take advantage of this warranty the product or part must be returned to us with transportation charges prepaid Proof of purchase date and an explanation of the complaint must accompany the merchandise If our inspection verifies the defect we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement We will return repaired products at our expense but if we determine there is no defect or that the defect resulted from causes not within the scope of our warranty then you must bear the cost of returning the product This warranty gives you specific legal rights and you may also have other rights which vary from state to state PITTSBURGH EE 3491 Mission Oaks Blvd PO Box 6009 Camarillo CA 93011 800 444 33
Download Pdf Manuals
Related Search