Harbor Freight Tools 40312 User's Manual
Contents
1. 13 Turn the Lubricator Body clockwise tightening the Fitting to the Air Filter Body 12 and the Lubricator Body A7 Note that the arrows imprinted on top of each body should be pointing all in the same direction Align both bodies so that their bowls are facing down Attach the mounting support Holder 6 to the Air Filter if the assembly is to be mounted to a flat surface Refer to the Assembly Drawings at the end of this manual Remove Screw 1 and pull up and remove the Adjusting Knob 3 Remove the Panel Mount Nut 4 by turning it counterclockwise Insert the Holder 6 and replace the Panel Mount Nut the Adjusting Knob and finally the screw Secure the whole assembly by the Holder to a flat surface using the appropriate hardware not supplied Connect the compressor air output hose or pipe to the air inlet connector on the Lubricator Body Connect the air output hose or pipe to the Air Filter output connector Press on the Lubricator Quick Release Button and pull off the Metal Bowl Guard A15 Twist off the Plastic Bowl A14 and add air lubricator oil to the maximum level Press up on the Plastic Bowl to replace it Snap in the Metal Bowl Guard Operation Turn on the Compressor and check for air leaks If any are found turn the Compressor off and fix the leak With the Compressor ON turn the Pressure Adjusting Knob 3 to adjust the air pressure as read on the Gauge 13 Adjust the oil2. flow by viewing the Visi dome 1A and adjusting the Oil Feed Adjustment Screw A3 Press on the Regulator Spring 14 button to expel any accumulated moisture from the Plastic Bowl 23 Do this daily SKU 40312 Page 5 Maintenance 1 Check oil level in Lubricator Plastic Bowl daily Refill if below minimum level 2 Press onthe Regulator Spring 14 button to expel any accumulated moisture in the Plastic Bowl 23 Air Filter Parts List Saal aR item Description Ce fre D7 ome KETE o retire E Fitting 1 4 Double sided PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THat ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO SKU 40312 Page 6 Air Filter Assembly Drawing NOTE Some parts are listed and shown for illustration purposes only and are not available
3. have them repaired by an authorized technician Stay alert Watch what you are doing use common sense Do not operate any tool when you are tired Check for damaged parts Before using any tool any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function Check for alignment and binding of moving parts any broken parts or mounting fixtures and any other condition that may affect proper operation Any part that is damaged should be properly repaired or replaced by a qualified technician Replacement parts and accessories When servicing use only identical replacement parts Use of any other parts will void the warranty Only use accessories intended for use with this tool Do not operate tool if under the influence of alcohol or drugs Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs If there is any doubt do not operate the tool Maintenance For your safety service and maintenance should be performed regularly by a qualified technician WARNING The brass components of this product contain lead a chemical known to the State of California to cause birth defects or other reproductive harm California Health amp Safety code 25249 5 et seq Caution Do not remove Part A1 Visi Dome from the lubricator Attempting to do so may damage the seal and thread Warning The warnings cautions
4. AIR FILTER REGULATOR AND LUBRICATOR Mfere 1140312 ASSEMBLY AND OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd Camarillo CA 93011 Visit our Web site at http www harborfreight com Copyright 2000 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools For technical questions and replacement parts please call 1 800 444 3353 Specifications Maximum Pressure 150 PSI Air Inlet Size 3 8 inch Mount Dimensions 2 1 2 inches center to center elongated holes Adjustable Pressure with Gauge Features Adjustable Lubrication Metal bowl covers Weight 4 5 lb Save This Manual You will need the manual for the safety warnings and precautions assembly instructions operating and maintenance procedures parts list and diagram Keep your invoice with this manual Write the invoice number on the inside of the front cover Keep the manual and invoice in a safe and dry place for future reference Safety Warnings and Precautions WARNING When using tool basic safety precautions should always be fol lowed to reduce the risk of personal injury and damage to equipment Read all instructions before using this tool 1 2 Keep work area clean Cluttered areas invite injuries Observe work area conditions Do not use machines or power tools in damp or wet locations Don t e
5. and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur It must be understood by the operator that common sense and caution are fac tors which cannot be built into this product but must be supplied by the opera tor REV 02e 07f SKU 40312 Page 3 Unpacking When unpacking check to make sure the following parts are included 1 Air Filter Regulator 2 Lubricator 3 Double sided Fitting If any parts are missing or broken please call Harbor Freight Tools at the number on the cover of this manual Installation The diagram below shows the general connections for the Air Filter Regulator and Lubricator Connector Coupler Air Tool 3 Air Hose Quick Reaulator 1 Find the 1 4 inch double sided Fitting 27 and apply brass fitting compound to both sides 2 Hand screw the Fitting into the Air Filter Body 12 right input side 3 Take the Lubricator Body A7 and align its output connection to the Fitting and hand screw the Fitting a few turns into the Lubricator Body z Screw 1 Pressure Adjusting Knob 3 Holder 6 gt l Air Filter Body 12 Fitting 27 Air Flow from Compressor la To Air Tool Lubricator Body A7 Quick Release Button Quick Release Button Metal Bowl Guard 26 Metal Bowl Guard A15 Regulator Spring 14 button _ SKU 40312 Page 4 10 11 12
6. individually as replacement parts SKU 40312 Page 7 Lubricator Parts List Lubricator Assembly Drawing Item Description NOTE Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts When ordering parts from this list add an A prefix to the part number illustrated in the Assembly Drawing Caution Do not remove Part A1 Visi Dome from the lubricator Attempting to do so may damage the seal and thread SKU 40312 Page 8 REV 05 02
7. xpose to rain Keep work area well lighted Do not use electrically powered tools in the presence of flammable gases or liquids Keep children away Children must never be allowed in the work area Do not let them handle machines tools or extension cords Store idle equipment When not in use tools must be stored in a dry location to inhibit rust Always lock up tools and keep out of reach of children Do not force tool It will do the job better and more safely at the rate for which it was intended Do not use inappropriate attachments in an attempt to exceed the tool capacity Do not overreach Keep proper footing and balance at all times Do not reach over or across running machines Use the right tool for the job Do not attempt to force a small tool or attachment to do the work of a larger industrial tool There are certain SKU 40312 Page 2 applications for which this tool was designed Do not modify this tool and do not use this tool for a purpose for which it was not intended Use eye and ear protection Always wear ANSI approved impact safety goggles Wear a full face shield if you are producing metal filings or wood chips Wear an ANSI approved dust mask or respirator when working around metal wood and chemical dusts and mists Maintain tools with care Keep tools sharp and clean for better and safer performance Follow instructions for lubricating and changing accessories Inspect tool cords periodically and if damaged
Download Pdf Manuals
Related Search