Harbor Freight Tools 40 ft. Retractable Cord Reel with Triple Tap Product manual
Contents
1. Owner s Manual amp Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions assembly operating inspection maintenance and cleaning procedures Write the product s serial number in the back of the manual near the assembly diagram or month and year of purchase if product has no number Keep this manual and the receipt in a safe and dry place for future reference a Harbor Freight Tools Brand Visit our website at http www harborfreight com Email our technical support at tech harborfreight com ITEM 61558 When unpacking make sure that the product is intact and undamaged If any parts are missing or broken AWARNING please call 1 800 444 3353 as soon as possible Copyright 2013 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in Read this material before using this product any shape or form without the express written consent of Harbor Freight Tools Failure to do so can result in serious injury Diagrams within this manual may not be drawn proportionally Due to continuing SAVE THIS MANUAL improvements actual product may differ slightly from the product described herein Tools required for assembly and service may not be included Specifications 1625W 13A 125VAC 14 AWG x 40 s EJ LISTED 59UT IMPORTANT SAFETY INFORMATION installation Precautions _ Install only according to these instru2. cessible connect this Cord Reel to a switch controlled outlet then if a malfunction occurs the Reel can be disconnected immediately Install out of reach of children Verify that installation surface has no hidden utility lines before drilling or driving screws Do not expose reels to rain or wet conditions Water entering a reel will increase the risk of electric shock If operating a reel in a damp location is unavoidable use a Ground Fault Circuit Interrupter GFCI protected supply Use of a GFCI reduces the risk of electric shock Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded If the plug will not fit the outlet have a proper outlet installed by a qualified electrician The plug must be connected to a properly grounded outlet If the reel should electrically malfunction or break down grounding provides a low resistance path to carry electricity away from the user reducing the risk of electric shock The grounding prong in the plug is connected through the green wire inside the cord to the grounding system in the reel The green wire in the cord must be the only wire connected to the reel s grounding system and must never be attached to an electrically live terminal The reel must be plugged into an appropriate outlet properly installed and grounded in accordance with all codes and ordinances Do not attach an extension cord to
3. ctions Improper Installation can create hazards 2 Wear ANSI approved safety goggles and heavy duty work gloves during installation 3 Keep Installation area clean and well lit 4 Keep bystanders out of the area during installation 5 Do not install when tired or when under the influence of alcohol drugs or medication Use Precautions This product is not a toy Do not allow children to play with or near this item 2 Wear ANSI approved safety goggles and heavy duty work gloves during use 3 Use as intended only 4 Inspect before every use do not use if parts are loose or damaged or if insulation is worn 5 Maintain product labels and nameplates These carry important safety information If unreadable or missing contact Harbor Freight Tools for a replacement o Plugs must match the outlet Never modify the plug in any way Do not use any adapter plugs Unmodified plugs and matching outlets will reduce risk of electric shock Avoid body contact with grounded surfaces such as pipes radiators ranges and refrigerators There is an increased risk of electric shock if your body is grounded 0 When pulling cord from the Cord Reel grasp the Reel s cord itself and not the device or tool the cord is plugged into Page 2 For technical questions please call 1 800 444 3353 Install the Cord Reel properly before connecting to the power supply If mounted in an area that is not readily ac
4. pection verifies the defect we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement We will return repaired products at our expense but if we determine there is no defect or that the defect resulted from causes not within the scope of our warranty then you must bear the cost of returning the product This warranty gives you specific legal rights and you may also have other rights which vary from state to state PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND INSTALLATION DIAGRAM IN THIS DOCUMENT AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYERASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO Item 61558 For technical questions please call 1 800 444 3353 Page 3 Parts List and Diagram E Record Product s Serial Number Here Note If
5. product has no serial number record month and year of purchase instead Note Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts a Harbor Freight Tools Brand 3491 Mission Oaks Blvd e PO Box 6009 Camarillo CA 93011 800 444 3353
6. surface Plug the reel into a grounded 3 prong switch controlled outlet 1 Pull cord out to desired length and stop The reel has stops to keep cord extended Limited 90 Day Warranty 2 To retract pull cord out and guide cord slowly back into the reel Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase This warranty does not apply to damage due directly or indirectly to misuse abuse negligence or accidents repairs or alterations outside our facilities criminal activity improper installation normal wear and tear or to lack of maintenance We shall in no event be liable for death injuries to persons or property or for incidental contingent special or consequential damages arising from the use of our product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS To take advantage of this warranty the product or part must be returned to us with transportation charges prepaid Proof of purchase date and an explanation of the complaint must accompany the merchandise If our ins
7. this item s input cord Do not open reel spring mechanism Spring may eject forcefully if housing is opened Item 61558 Installation Instructions gt _ Unplug the cord reel before installing N Select a mounting location within 2 feet of a grounded 3 prong switch controlled outlet The cord reel must be mounted to a stud joist or similar sturdy mounting location able to support cord reel and withstand stress from use WARNING Verify that installation surface has no hidden utility lines before drilling or driving screws 3 Use mounting holes in the Mounting Bracket 16 as a template to mark the spots where holes will need to be drilled in the installation surface Operation Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document including all text under subheadings therein before set up or use of this product 4 Drill holes at marked locations Use 3 8 diameter hardware at least 1 long sold separately to mount the Cord Reel Using smaller hardware may allow the Reel to slip off of the hardware and fall possibly causing injury Hang the Reel so that the hardware heads fit tightly into the thin end of the mounting holes in the Mounting Bracket Install a 1 long 3 8 diameter screw in the center round hole to ensure the reel will not come off the hardware heads Pull on and move the unit back and forth to make sure it is tightly secured to the
Download Pdf Manuals
Related Search