Harbor Freight Tools 4 in. Swivel Vise with Anvil Product manual
Contents
1. legal rights and you may also have other rights which vary from state to state 3491 Mission Oaks Blvd PO Box 6009 Camarillo CA 93011 800 444 33532. Owner s Manual amp Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions assembly operating inspection maintenance and cleaning procedures Write the product s serial number in the back of the manual near the assembly diagram or month and year of purchase if product has no number Keep this manual and the receipt in a safe and dry place for future reference ITEM 61553 RUGGED CAST IRON ITEM 61551 SWIVEL VISE with ANVIL Visit our website at http www harborfreight com Email our technical support at tech harborfreight com When unpacking make sure that the product is intact and undamaged If any parts are missing or broken AWARNING please call 1 800 444 3353 as soon as possible Copyright 2013 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in Read this material before using this product any shape or form without the express written consent of Harbor Freight Tools Failure to do so can result in serious injury Diagrams within this manual may not be drawn proportionally Due to continuing SAVE THIS MANUAL improvements actual product may differ slightly from the product described herein Tools required for assembly and service may not be included Specifications Base 360 Swivel Base Jaw Opening 4 5 8 Maximum 5 1 2 Maximum 2 3 4 x 2 5 8 3 1 2 x 3 1 2 5 3 4 x 5 3 4 Im
3. from its mounting PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS DOCUMENT AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO Item 61551 53 For technical questions please call 1 800 444 3353 Page 3 Parts List and Diagram s Tease Handle 3 6 Base Nut not shown 1 _ Note Specify vise item number when ordering parts Record Serial Number Here Note If product has no serial number record month and year of purchase instead Note Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts Limited 90 Day Warranty Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards and warrants to the original purchaser that this product is free fr
4. g holes are positioned Carefully set the Base with the Mounting Holes corresponding to the holes previously drilled through the top of the workbench as desired With a pencil mark the points at which to fasten the Vise onto the workbench Set the Vise aside Note Mounting bolt diameter should fit mounting holes Mounting bolt length is based on workbench thickness N Drill holes of the appropriate size where previously marked with a pencil through the top of the workbench AWARNING Before drilling holes check for hidden electrical wires or cords in drilling path Insert hardened steel bolts not provided of the appropriate diameter and length downward through the Base and the workbench Secure the mounting bolts with the appropriate washers and nuts Operation Instructions Loosen the two Base Handles to oF allow the Base to pivot Tighten the Base Handles before working Place the workpiece inside the Jaws Tighten Jaws against the workpiece by turning the Handle clockwise until it is held securely inside the Jaws N Turn the Handle counterclockwise to open the Jaws of the Vise Maintenance 1 Keep the moving parts lubricated 3 The jaws can be removed for Wipe off any lubricant on cleaning and are replaceable the Handles and Jaws Each is held on by two cap screws N Keep the Jaws clean 4 Check and tighten the mounting screws bolts to be sure the vise has not loosened
5. om defects in materials and workmanship for the period of 90 days from the date of purchase This warranty does not apply to damage due directly or indirectly to misuse abuse negligence or accidents repairs or alterations outside our facilities criminal activity improper installation normal wear and tear or to lack of maintenance We shall in no event be liable for death injuries to persons or property or for incidental contingent special or consequential damages arising from the use of our product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS To take advantage of this warranty the product or part must be returned to us with transportation charges prepaid Proof of purchase date and an explanation of the complaint must accompany the merchandise If our inspection verifies the defect we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement We will return repaired products at our expense but if we determine there is no defect or that the defect resulted from causes not within the scope of our warranty then you must bear the cost of returning the product This warranty gives you specific
6. portant Safety Information 1 Mount before use according to these instructions Improper mounting can create hazards 2 Wear ANSI approved safety goggles and heavy duty work gloves during mounting and use G Keep work area clean and well lit va Keep bystanders out of the area during use 5 Before drilling holes check for hidden utility lines in drilling path 6 Do not use when tired or when under the influence of alcohol drugs or medication 7 This product is not a toy Do not allow children to play with or near this item 8 Use as intended only 9 ta Inspect before every use do not use if parts are loose or damaged Do not exceed listed weight capacity Be aware of dynamic loading Sudden load movement may briefly create excess load causing product failure Maintain product labels and nameplates These carry important safety information If unreadable or missing contact Harbor Freight Tools for a replacement When working with the Anvil do not strike with a hardened tool It could chip the Anvil and or the tool Damage could occur to your vise and or workpiece if you overtighten the Handle save THESE INSTRUCTIONS Forge Page 2 For technical questions please call 1 800 444 3353 Item 61551 53 Mounting Instructions A Use the mounting holes on the Base as a template to mark drill points Set the Vise flat on the workbench so that the mountin
Download Pdf Manuals
Related Search