Harbor Freight Tools 38413 User's Manual
Contents
1. 13 For technical questions please call 1 800 444 3353 Page 62. CENTRAL FORGE o THROATLESS SHEAR ASSEMBLY AND OPERATING INSTRUCTIONS Visit our website at http Awww harborfreight com Read this material before using this product Failure to do so can result in serious injury SAVE THIS MANUAL Copyright 1998 2009 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools Diagrams within this manual may not be drawn proportionally Due to continuing improvements actual product may differ slightly from the product described herein Tools required for assembly and service may not be included For technical questions or replacement parts please call 1 800 444 3353 Revised 09i Thank you for choosing a Harbor Freight Tools product For future reference please complete the owner s record below Model Purchase Date Save the receipt and these instructions It is important that you read the entire instruction sheet to become familiar with this product before you begin using it Technical Specifications Designed to allow you to turn the workpiece at any angle for straight curved and irregular cuts Will cut mild steel aluminum stainless steel or lighter material 18 handle for good leverage Blades Alloy tool steel 4 length Dimensions 8 1 4 x 13 1 2 x 27 1 4 Base Size 5 1 8 x 3 7 8 with three mounti
3. EV 03d 03 05i SKU 38413 For technical questions please call 1 800 444 3353 Page 4 Assembly Diagram NOTE Some parts are listed and shown for illustration purposes only 4 and are not available individually as replacement parts PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARIS ING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO REV 03d SKU 38413 For technical questions please call 1 800 444 3353 Page 5 LIMITED 90 DAY WARRANTY Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase This warranty does not apply to damage due directly or indirectly to misuse a
4. buse negligence or accidents repairs or alterations outside our facilities criminal activity improper installation normal wear and tear or to lack of maintenance We shall in no event be liable for death injuries to persons or property or for incidental contingent special or consequential damages arising from the use of our product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS WARRANTY IS EX PRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS To take advantage of this warranty the product or part must be returned to us with trans portation charges prepaid Proof of purchase date and an explanation of the complaint must accompany the merchandise If our inspection verifies the defect we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement We will return repaired products at our expense but if we determine there is no defect or that the defect resulted from causes not within the scope of our warranty then you must bear the cost of returning the product This warranty gives you specific legal rights and you may also have other rights which vary from state to state 3491 Mission Oaks Blvd e PO Box 6009 Camarillo CA 93011 800 444 3353 SKU 384
5. irregular cuts are made by turning the workpiece while following through with the downward stroke of the blade 3 When a cut has been finished push the workpiece forward while raising the handle to lift the blade above the workpiece Start the next cut at the heel of the blade 4 Always keep the material being cut flat on the bed of the shear SKU 38413 For technical questions please call 1 800 444 3353 Page 3 Maintenance a Periodically use a good graphite oil to lubricate blade edges and gears on the Geared Handle 4 2 To Replace the Blades 8 14 a Open jaws completely Be sure to use caution when replacing the blade if the handle is bumped the blades may move causing personal injury b Remove all three Bolts 13 replace Upper Blade 14 and secure Blade with Bolts 13 c Loosen Bolt 9 replace Lower Blade 8 and loosen Adjusting Bolts 15 16 d Adjust the Lower Blade 8 to the proper clearance for the workpiece to be cut by using the Adjusting Bolts 15 16 e After the Lower Blade 8 is properly adjusted tighten Bolt 9 to secure it in place Parts List Part Description Q ty Description Q ty 1 Base 1 Clamp 1 2 Right Stand 1 Nut M12 1 3 Blade Stand 1 Bolt M12 2 4 Geared Handle 1 Bolt M5x8 3 5 Bolt M8x16 1 Upper Blade 1 6 Handle 1 Adjusting Bolts M5x35 1 7 Handle Bushing 1 Adjusting Bolt M5x20 1 8 Lower Blade 1 Spring Washer 1 R
6. ng holes 3 8 diameter Tool Weight 16 4 Ibs Warning Common sense and caution are factors which cannot be built into any product These factors must be supplied by the operator Please remember 1 Prevent body contact with grounded surfaces such as pipes radiators etc Stay alert Never operate equipment or use tools if you are tired Ned Do not use this product if under the influence of alcohol or drugs Read warning labels on prescriptions to determine if your judgement or reflexes might be impaired Do not wear loose clothing or jewelry as they can be caught in moving parts Nonskid footwear is recommended Wear restrictive hair covering to contain long hair No oo o ooe Use eye and ear protection Always wear ANSI approved safety glasses when using equip ment or tools 8 Keep proper footing and balance at all times Work Area To avoid risk of personal injury equipment damage fire and shock make sure your work area is 1 Free of damp wet or rainy conditions 2 Free of flammable gasses or liquids 3 Free of children Children should never handle tools or operate equipment SKU 38413 For technical questions please call 1 800 444 3353 Page 2 4 Make sure your work area is well lighted Clean and uncluttered work spaces contribute to safe and productive work conditions Before Operating i Check for damaged parts Before using any tool any part that appears damaged should be carefully checked
7. to determine that it will operate properly and perform its intended function 2 Check for alignment and binding of all moving parts broken parts or mounting fixtures and any other condition that may affect proper operation Any part that is damaged should be properly repaired or replaced by a qualified technician Operation 1 Never force the tool or attachment to do the work of a larger industrial tool It is designed to do the job better and more safely at the rate for which it was intended 2 Never use the blades if they are dull worn or chipped Blades must be sharpened re paired or replaced before using 3 Check to make sure all bolts are secure but not overtightened Check for blade clearance Make sure clearance is suitable for the workpiece 4 While being used the lower blade must be secured with the Clamp When not being used the Clamp 10 can be loosened 5 Minor assembly of the Throatless Shear is required Assemble the Handle 6 over the exposed shaft of the Geared Handle 4 and tighten Bolt 5 Using the Throatless Shear Le Adjust the clearance between the Upper Blade 14 and Lower Blade 8 To decrease the clearance turn the Adjusting Bolts 15 clockwise To increase clearance turn the bolts counterclockwise The clearance can be adjusted to between 1 4 and 1 10 of the thickness of the workpiece 2 To gain power and control of the workpiece start all cuts at the heel of the blades Circu lar and
Download Pdf Manuals
Related Search