Harbor Freight Tools 36 LED Solar Security Light Product manual
Contents
1. set to OFF allow to charge in full on and off with sunlight for 8 hours before further use clicking sounds 2 Battery worn out 2 The internal Battery is non replaceable Replace the Lamp assembly once the Battery will no longer charge effectively Frequent changes in Check sensing area for possible heat sources such heat being detected as air vents vehicles or objects in wind Reposition the Motion Detector Light if needed Light brightens 1 Changes in heat are being 1 Check sensing area for possible heat sources and darkens detected from a fixed heat Such as air vents vehicles or objects in wind continuously source or moving object Reposition the Motion Detector Light 2 Sudden temperature change 2 Turn Power Switch OFF until storm passes due to storms or high winds Mount in a sheltered location Follow all safety precautions whenever diagnosing or servicing the tool Disconnect power supply before service Page 6 For technical questions please call 1 888 866 5797 Item 69644 Parts List and Diagram PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACT2. Owner s Manual amp Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions assembly operating inspection maintenance and cleaning procedures Write the product s serial number in the back of the manual near the assembly diagram or month and year of purchase if product has no number Keep this manual and the receipt in a safe and dry place for future reference Bunker Hill Security ITEM 69644 36 LED Solar Security Light Visit our website at http www harborfreight com Email our technical support at productsupport harborfreight com When unpacking make sure that the product is intact and undamaged If any parts are missing or broken please call 1 888 866 5797 as soon as possible Copyright 2012 by Harbor Freight Tools All rights reserved A y 5 S No portion of this manual or any artwork contained herein may be reproduced in Read this material before using this product any shape or form without the express written consent of Harbor Freight Tools Failure to do so can result in serious injury Diagrams within this manual may not be drawn proportionally Due to continuing SAVE THIS MANUAL improvements actual product may differ slightly from the product described herein Tools required for assembly and service may not be included o gt mn m lt Table of Contents Safety i intct rette R 2 Maintenarnce teet iot inet ide 6 Specifications 5 eset rettet dd 4 Pa
3. URER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO Partt Description Qty Part Description Qty 6 Scew 4 Solar Panel Anchor Sleeve Mounting Bracket 8 Power Cord not shown 4 Adjustable Hinge 5 Wing Nut and Bolt set Oe SSeS SSIS 4 mE a Record Product s Serial Number Here MAINTENANCE Note If product has no serial number record month and year of purchase instead Note Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts Item 69644 For technical questions please call 1 888 866 5797 Page 7 Limited 90 Day Warranty Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase This warranty does not apply to damage due directly or indirectly to misuse abuse negligence or accidents repairs or alterations outside our facilities criminal activity improper installation normal wear and tear or to l
4. ack of maintenance We shall in no event be liable for death injuries to persons or property or for incidental contingent special or consequential damages arising from the use of our product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS To take advantage of this warranty the product or part must be returned to us with transportation charges prepaid Proof of purchase date and an explanation of the complaint must accompany the merchandise If our inspection verifies the defect we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement We will return repaired products at our expense but if we determine there is no defect or that the defect resulted from causes not within the scope of our warranty then you must bear the cost of returning the product This warranty gives you specific legal rights and you may also have other rights which vary from state to state Bunker Hill Security 3491 Mission Oaks Blvd PO Box 6009 Camarillo CA 93011 1 888 866 5797
5. ar Panel Detects Motion Range of Motion Up to 120 30 Seconds Delay Time Setup Before Use Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product Note For additional information regarding the parts listed in the following pages refer to Parts List and Diagram on page 7 Installation 1 Decide where you want to place the Lamp and 3 Mount the Lamp the Solar Panel The Solar Panel is equipped with a 16 ft connecting wire so the Lamp and Solar Panel can be installed up to 16 ft apart Set the Solar Panel in a location that receives full direct sunlight a minimum of eight hours a day Angle the solar panel slightly toward the south northern hemisphere a Locate the unit six to eight feet above ground on a solid surface capable of supporting the Lamp and secure enough so that it will not move when exposed to vibrations or wind The unit must be high enough to allow for motion detection and light distribution b Mark the hole locations of the 2 Mount the Solar Panel Mounting Bracket then set the Lamp aside a Place the Solar Panel in the desired location adjusting the unit to best fit the surface b Mark the hole locations of the Base then set the Solar Panel aside c Check that the marked areas are clear of obstacles such as cables and electrical lines Drill holes for the encl
6. he Light Lithium Battery Safety Warnings 2 LITHIUM BATTERIES STORE A LARGE AMOUNT OF ENERGY AND WILL VENT FIRE OR EXPLODE IF MISTREATED 3 4 12 13 Have your product serviced by a qualified repair person using only identical replacement parts This will ensure that the safety of the product is maintained WARNING The cord of this product contains lead a chemical known to the State of California to cause cancer and birth defects or other reproductive harm Wash hands after handling California Health amp Safety Code 25249 5 et seq SAFETY The warnings precautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur It must be understood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator Keep Battery dry DO NOT DO ANY OF THE FOLLOWING TO THE BATTERY a Open Drop Short circuit Puncture Incinerate or Expose to temperatures greater than 140 F 0o20o0c Charge Battery only according to instructions Do not use or charge battery if damaged A SAVE THESE INSTRUCTIONS Bunker Hill Security Item 69644 For technical questions please call 1 888 866 5797 Page 3 Specifications Lamp 36 LED lamps with reflective intensifier Battery Pack 3 2V 600mAh Li ion 4 x 3 Amorphous Silicon Up to 20 Sol
7. osed Screws and Anchor Sleeves d Insert the Anchor Sleeves then secure the Solar Panel in place with the Screws c Check that the marked areas are clear of obstacles such as cables and electrical lines Drill holes for the enclosed Screws and Anchor Sleeves d Insert the Anchor Sleeves then secure the Lamp in place with the screws Figure A Carefully route the Power Cord of the Solar Panel to the Lamp and plug it into the Outlet on the back of the Lamp Initial Battery Charging Before the Security Light can operate properly the 1 Turn OFF the Power Switch battery need to be fully charged To charge the battery The battery will recharge without turning on the light while the Power Switch is off 2 Allow the battery to charge for 8 hours of full sunlight Page 4 For technical questions please call 1 888 866 5797 Item 69644 Functions Solar Panel Back of Lamp Wing Nut E NN Mounting Hole Power Switch Outlet Figure B Base Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product 1 Move the Power Switch to ON to 4 The lamp should brighten temporarily activate the Solar Security Light when motion is detected 2 The Light will automatically turn 5 If the Lamp does not brighten relocation or aiming ON dimly during the night adjustment or more charging time will be re
8. quired 3 Test the Light by walking or driving into the protected area Z o E lt nc Lu n Oo Item 69644 For technical questions please call 1 888 866 5797 Page 5 AONVNALNIVIN Maintenance and Servicing Procedures not specifically explained in this manual must be performed only by a qualified technician AWARNING TO PREVENT SERIOUS INJURY FROM TOOL FAILURE Do not use damaged equipment If abnormal noise or vibration occurs have the problem corrected before further use Cleaning Maintenance and Lubrication 1 BEFORE EACH USE inspect the general 2 AFTER USE wipe external surfaces condition of the tool Check for of the tool with clean cloth loose hardware misalignment or binding of parts cracked or broken parts and any other condition that may affect its safe operation e 3 The internal Battery is non replaceable Replace the Lamp assembly once the Battery will no longer charge effectively e e Troubleshooting Possible Causes Likely Solutions 1 Power is not on 1 Check that Power Switch is set to ON 2 Cable connection is loose 2 Plug in firmly at back of Battery Housing 3 Battery pack not fully charged 3 Keep solar panel clean Allow to charge in full sunlight for 8 hours with the Power Switch OFF Light turns on Light is positioned in Move light to a location that is lit during the day during day a dark location Light flashes 1 Low battery 1 With Switch
9. roperly and perform its intended function Check for any broken or damaged parts and any other conditions that may affect its operation Replace or repair damaged or worn parts immediately Do not use the Security Light if any switch does not turn on and off properly Page 2 For technical questions please call 1 888 866 5797 Check hardware and assembled parts after assembling All connections should be tight and hardware tightened Keep children away Mount the Light Solar Panel and Cord out of children s reach Dress properly Protective electrically non conductive clothes and nonskid footwear are recommended when working with the Solar Powered Security Light Wear restrictive hair covering to contain long hair Item 69644 8 Use eye protection Wear ANSI approved impact safety goggles when setting up this product 9 Maintain products with care Keep the Solar Powered Security Light clean for better and safer performance Inspect the Light periodically If damaged have it repaired by a qualified technician 10 Do not overreach Keep proper footing and balance at all times If a ladder is to be used during installation it should be supported by an assistant 14 11 Do not set up the Solar Powered Security Light if under the influence of alcohol or drugs Read warning labels on prescriptions to determine if your judgement or reflexes are impaired while taking drugs If there is any doubt do not set up t
10. rts List and Diagram 7 SetU Peine e an a det RN 4 Warranty ssns tec a e A 8 Operation nero teen 5 Bunker Hill Security WARNING SYMBOLS AND DEFINITIONS This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death Indicates a hazardous situation which if not avoided will result in death or serious injury A DANGER AWARNING ACAUTION Indicates a hazardous situation which if not avoided could result in death or serious injury Indicates a hazardous situation which if not avoided could result in minor or moderate injury NOTICE CAUTION IMPORTANT SAFETY INFORMATION AWARNING Read all safety warnings and instructions Failure to follow the warnings and instructions may result in electric shock fire and or serious injury Save all warnings and instructions for future reference Addresses practices not related to personal injury 4 Replacement parts and accessories When servicing use only identical replacement parts Use of any other parts will void the warranty 1 Keep installation area clean Cluttered areas invite accidents 2 Observe installation area conditions Keep work area well lit during installation Check for damaged parts Before using any product any part that appears damaged should be carefully checked to determine that it will operate p
Download Pdf Manuals
Related Search