Harbor Freight Tools 350 Lb. Capacity Motocross Dirt Bike Stand Product manual
Contents
1. e Washer 9 Secure Long Bolt with a Lock Nut 8 Insert Short Bolt 7 through e Washer 9 e Mounting Bracket 5 e Washer 9 e Remaining hole in Pedal 3 e Washer 9 e Remaining Mounting Bracket 5 e Washer 9 Secure Short Bolt with a Lock Nut 8 Insert remaining Short Bolt 7 through e Washer 9 e Release Bar 4 e Washer 9 e Remaining hole in Mounting Brack et 5 e Washer 9 SKU 66552 For technical questions please call 1 800 444 3353 Page 4 e Hole in foot on Base 2 e Washer 9 e Remaining hole in second Mounting Bracket 5 e Washer 9 7 Secure Short Bolt with Lock Nut 8 8 Before using the Bike Stand with a load test the operation of the Pedal and Release Bar without any load following the operating instructions below 4 Insert Locking Pin 11 fully through the hole in the saddle and the base OPERATING INSTRUCTIONS to secure the stand in the up position Lock it in place with the R Pin 12 SAFETY INFORMATION 5 AWARNING Stay clear of Release section at the beginning of this Bar while Saddle is elevated and in manual including all text under use subheadings therein before set up or use of this product 1 Read the ENTIRE IMPORTANT 6 Remove tools from under stand be fore lowering 1 Locate Stand on hard flat and level surface able to withstand load without 7 TO lower Saddle keep clear and remove the R Pin and Locking P2. ALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO Page 6 PARTS LIST PARTS LIST Description Part Qty Bushing _ 2 1 Bushing Mounting Bracket 6 M10X70 Bolt Long Bolt RPin S 9 1 8 10 9 8 9 8 9 5 2 9 3 9 6 9 5 9 9 9 7 9 7 4 Note Locking Pin 11 and R Pin 12 not shown Record Product s Serial Number Here Note If product has no serial number record month and year of purchase instead Note Some parts are listed and shown for illustration purposes only and are not avail able individually as replacement parts SKU 66552 For technical questions please call 1 800 444 3353 Page 7 LIMITED 90 DAY WARRANTY Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards and warrants to the original purchaser that this prod uct is free from defects in materials and workmanship for the period of 90 days from the date of purchase This wa
3. HAUL MASTER MOTOCROSS DIRT BIKE STAND SET UP AND OPERATING INSTRUCTIONS Distributed exclusively by Harbor Freight Tools 3491 Mission Oaks Blvd Camarillo CA 93011 Visit our website at http www harborfreight com Read this material before using this product Failure to do so can result in serious injury SAVE THIS MANUAL Copyright 2008 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools Diagrams within this manual may not be drawn proportionally Due to continuing improvements actual product may differ slightly from the product described herein Tools required for assembly and service may not be included For technical questions or replacement parts please call 1 800 444 3353 SAVE THIS MANUAL Keep this manual for the safety warn ings and precautions assembly operat ing inspection maintenance and cleaning procedures Write the product s serial number in the back of the manual near the assembly diagram or month and year of purchase if product has no number Keep this manual and the receipt in a safe and dry place for future reference IMPORTANT SAFETY INFORMATION In this manual on the labeling and all other information provid ed with this product This is the safety alert symbol It is used to alert you to potential personal inj
4. ear eye protection Safety equipment such as dust mask non skid safety shoes hard hat or hearing protection used for appropri ate conditions will reduce personal injuries SKU 66552 For technical questions please call 1 800 444 3353 Page 2 c Do not overreach Keep proper footing and balance at all times This enables better control of the tool in unexpected situations d Dress properly Do not wear loose clothing or jewelry Keep your hair clothing and gloves away from moving parts Loose clothes jewelry or long hair can be caught in moving parts e Only use safety equipment that has been approved by an appropri ate standards agency Unapproved safety equipment may not provide adequate protection Eye protection must be ANSI approved and breath ing protection must be NIOSH ap proved for the specific hazards in the work area Motocross Bike Stand Safety Warnings Strap load to Saddle before lifting 2 Keep clear of Release Bar and do not leave unattended while supporting load 3 Do not exceed 350 Ib capacity 4 Center load on Saddle 5 Raise and lower using second person to stabilize load 6 Keep out from under load while low ering 7 Inspect before every use do not use if parts are loose or damaged 8 Use as intended only 9 Operate on flat and level surface 10 Do not rock load on Stand SKU 66552 11 For technical questions please call 1 800 444 3353 Keep out of reach of child
5. in deforming Place foot on Release Bar and Pedal 2 Center dirt bike over Saddle and se Using second person to stabilize cure to Saddle with tie down strap load press on Release bar while sold separately before lifting guiding Pedal up to smoothly lower 3 Using second person to stabilize Saddle load slowly raise Saddle by de pressing Pedal with your foot until Saddle is fully raised SKU 66552 For technical questions please call 1 800 444 3353 Page 5 MAINTENANCE AND SERVICING Procedures not specifically explained in this manual must be performed only by a qualified technician TO PREVENT AWARNING serious INJURY FROM TOOL FAILURE Do not use damaged equipment If abnormal noise or vibration occurs have the problem corrected before further use Cleaning and Maintenance 1 BEFORE EACH USE inspect the general condition of the tool Check for loose screws misalignment or binding of moving parts cracked or broken parts and any other condition that may affect its safe operation 2 AFTER USE clean external surfaces of the tool with clean cloth SKU 66552 For technical questions please call 1 800 444 3353 PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QU
6. on Oaks Blvd PO Box 6009 Camarillo CA 93011 800 444 3353 SKU 66552 For technical questions please call 1 800 444 3353 Page 8
7. ren Maintain labels and nameplates on the tool These carry important safety information If unreadable or miss ing contact Harbor Freight Tools for a replacement The warnings precautions and in structions discussed in this instruction manual cannot cover all possible con ditions and situations that may occur It must be understood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator SAVE THESE INSTRUCTIONS Page 3 SPECIFICATIONS UNPACKING When unpacking make sure that the item is intact and undamaged If any parts are missing or broken please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible ASSEMBLY Read the ENTIRE IMPORTANT A SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product Note For additional information regarding the parts listed in the following pages refer to the Assembly Diagram near the end of this manual 1 Make sure rubber end caps are se cured into feet of Base 2 Steps 4 and 5 Steps 6 and 7 Steps 2 and 3 U Shaped Bracket r lt l f Long Bolt Insert Long Bolt 6 through e Washer 9 e One hole in U shaped Bracket un der Saddle 1 e Bushing 10 e Hole in end of Pedal 3 e Bushing 10 e Other hole in U shaped Bracket
8. rranty does not apply to damage due directly or indirectly to misuse abuse negligence or accidents repairs or alterations outside our facilities criminal activity improper installation normal wear and tear or to lack of maintenance We shall in no event be liable for death injuries to persons or property or for incidental contingent special or consequential damages arising from the use of our product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS WARRANTY IS EXPRESS LY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS To take advantage of this warranty the product or part must be returned to us with transportation charges prepaid Proof of purchase date and an explanation of the com plaint must accompany the merchandise If our inspection verifies the defect we will ei ther repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement We will return re paired products at our expense but if we determine there is no defect or that the defect resulted from causes not within the scope of our warranty then you must bear the cost of returning the product This warranty gives you specific legal rights and you may also have other rights which vary from state to state 3491 Missi
9. ury hazards Obey all safety messages that follow this symbol to avoid possible injury or death DANGER indicates A DANGER a hazardous situation which if not avoided will result in death or serious injury AWARNING WARNING indicates a hazardous situation which if not avoided could result in death or serious injury ACAUTION CAUTION used with the safety alert symbol indicates a hazardous situation which if not avoided could result in minor or moderate injury 1 NOTICE is used to NOTICE address practices not related to personal injury CAUTION CAUTION without the safety alert symbol is used to address practices not related to personal injury General Safety Warnings WARNING Read all safety warnings and instructions Failure to follow the warnings and instructions may result in serious injury Save all warnings and instructions for future reference Work area safety a Keep work area clean and well lit Cluttered or dark areas invite acci dents b Keep children and bystanders away while operating a tool Dis tractions can cause you to lose con trol Personal safety a Stay alert watch what you are do ing and use common sense when operating a tool Do not use a tool while you are tired or under the influence of drugs alcohol or medication A moment of inattention while operating tools may result in serious personal injury b Use personal protective equip ment Always w
Download Pdf Manuals
Related Search