Harbor Freight Tools 32826 User's Manual
Contents
1. IMPORTANT SAFETY INSTRUCTIONS A READ ALL INSTRUCTIONS BEFORE USING THIS PRODUCT Warning The warnings cautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur It must be understood by the operator that COMMON SENSE AND CAUTION ARE FACTORS WHICH CANNOT BE BUILT INTO THIS PRODUCT BUT MUST BE SUPPLIED BY THE OPERATOR The Operator PLEASE REMEMBER Do not operate the product if under the influence of alcohol or drugs Read warning labels on prescriptions to determine if your judgment reflexes might be impaired Be careful not to get fingers hands or feet under the tires Keep hands and feet inside the Wagon Protective gloves and non skid footwear is recommended Be very cautious when using the wagon on rough terrain Use caution when going over steps and curbs Only one person on wagon at a time Do not exceed the maximum weight capacity An approved safety helmet must be worn at all times Use only under adult supervision 32826 REV 08d Page 2 Before Operating Before using your Wagon any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function Before operating your Big Foot Panel Wagon check for damaged parts Do not over inflate the tires Check the instructions on the tires for proper air pressure Inspect all parts for sharp edges before using your wagon Great2. Tighten the Bolt into place with a Small Washer and Nut Cap Turn the Wagon upright Attach one 1 of the Long Side Panels part E to the wagon with the three 3 1 3 4 Bolts going through both the Tray and each vertical slat The top of the Bolts should be on the inside of the Tray Tighten each into place with a washer then a Nut Cap The Short Front Panel part G is the one with a downward curved front slat Attach the Short Rear Panel part F to the wagon with two 2 1 3 4 Bolts going through the Tray A and each vertical slat Tighten into place by sliding on the washer followed by the Nut Cap Attach the second Long Side Panel part E as in step 9 Attach the Short Front Panel part G with two 2 1 3 4 Bolts Tighten into place with the Washer and Nut Cap as previously described Operation Your Wagon has a long handle mounted at the front Use the handle to pull the wagon to your destination as well as transporting loads to and from your destination Turning the Handle part B will cause the front wheels on the wagon to turn Turn the Handle in the direction that you wish the wagon to go The Handle can be raised for steering from inside the wagon or lowered so that the wagon can be pulled from in front IF THERE IS ANY QUESTION ABOUT A CONDITION BEING SAFE OR UNSAFE DO NOT OPERATE THE WAGON PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANU
3. care has been taken to assure smooth surfaces but a complete inspection before using could prevent injury Periodically inspect all nuts bolts and tires to make certain that they are tight and properly inflated Make certain to park the Wagon on a level and secure area Assembly Your Wagon comes unassembled For assistance with assembly please refer to the parts list and the Assembly diagram on page 5 It is recommended that your wagon be assembled with the Tray placed over sawhorses or sturdy cartons This allows easy access to the wagon and protects it from damage during assembly Do not use excessive force when tightening the screws as this may result in damage to the support arms Step 1 With the Tray part A upside down so the bottom is facing upward place it over saw horses or sturdy cartons Step 2 Attach the Rear Axle Assembly part H to the Tray A using two 2 1 2 Bolts Line up the Rear Axle Assembly with the holes located at the very back of the Wagon Insert the Bolt so that the small washers small lock washers and cap nuts found in Hardware bag K are screwed on from the underside of the wagon Step 3 Slide each of the Rear Axle Braces part over the end of each Rear Axle until they sit firmly to the inside of the Rear Axle Assembly H Line up the end of the Braces with the holes in the wagon Using two 2 1 2 Bolts insert the bolts from the top of the wagon so that the small washers lock washers
4. cotter pins wheels large flat washers wheels Axle caps 1 1 8 Bolt with hole 7 8 Washer large lock washer and Hex Nut attaching Turntable to Steering Assembly Qty _ ane ee ee oe Page 5
5. AL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO 32826 REV 02g Page 4 When unpacking your Big Foot Panel Wagon check to make sure the following parts are included If any parts Unpacking are missing or broken please call Harbor Freight Tools at 1 800 444 3353 Parts List 32826 u Q e Description Tray Handle Wheels Turntable Long Side Panel Short Rear Panel Short Front Panel Rear Axle Assembly Rear Axle Braces Steering Assembly e TOm mmovoowa gt Assembly Diagram 32826 32826 lt DNMNrHH HNO PH H D K Assembly Hardware Bag Contains All bolts are 6mm thread and include a flat washer and nut to match 1 3 4 round head bolts w nuts amp washers 2 5 8 round head bolt handle w nut amp washer 1 2 flat head bolts axle amp steering yoke fasteners w nuts amp washers
6. HAUL MASTER BIG FOOT PANEL WAGON Model ASSEMBLY amp OPERATING INSTRUCTIONS Diagrams within this manual may not be drawn proportionally Due to continuing improvements actual product may differ slightly from the product described herein Distributed exclusively by Harbor Freight Tools 3491 Mission Oaks Bivd Camarillo CA 93011 Visit our website at http www harborfreight com Read this material before using this product Failure to do so can result in serious injury SAVE THIS MANUAL Copyright 1999 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools For technical questions or replacement parts please call 1 800 444 3353 THANK YOU for choosing a HARBOR FREIGHT TOOLS product For future reference please complete the owner s record below Model Serial No Purchase Date SAVE THE RECEIPT WARRANTY AND THESE INSTRUCTIONS It is important that you read the entire manual to become familiar with the unit BEFORE you begin assembly Technical Specifications Tool Name Big Foot Panel Wagon Item Number 32826 Tires Pneumatic 10 Deck Size 33 5 8 x 15 3 4 x 5 1 2 Max Weight Capacity 330 Lbs Inside Dimensions 31 7 8 x 13 3 4 x 4 Optional Accessory Spare wheels Item 30900 are available through Harbor Freight Tools
7. and the nut part K are secured on the underside of the wagon Step 4 Attach the Turntable part D to the Steering Assembly part J Attach the Steering Assembly to the Turntable using the 1 1 8 Bolt with Hole Slide the Bolt through the underside of the Steering Assembly J and into the Turntable part D Secure it from inside the Turntable with the 7 8 Washer the Large Lock Washer and the Hex Nut Loosely thread the Hex Nut onto the Bolt Insert the Cotter Pin through the hole and spread it open Step 5 Attach both parts now one assembled unit as shown in Step 4 the Steering Assembly part J and the Turntable part D to the Tray A Insert each of the four 4 1 2 Bolts from the top of the wagon and tighten it into place from the bottom of the Tray with four 4 small washers four 4 small lock washers and four nuts Step 6 Slide each of the four 4 Wheels part C onto an axle with the Air Valve facing out Slide two 2 1 1 4 Washers onto each axle one on each side of the Wheel After the Wheel and the Washers are in place attach the Cotter Pin to the outside of the Wheel 32826 Page 3 Step 7 Step 8 Step 9 Note Step 10 Step 11 Attach each of the four 4 Axle Caps from Bag part K to the Axles Insert the lower part of the Handle part B into the Steering Assembly part J Slide the 2 5 8 Bolt into the Assembly and through the Handle so that it exits the other side of the Assembly
Download Pdf Manuals
Related Search