Harbor Freight Tools 3/8 in. x 30 Ft. Air Hose Reel Product manual
Contents
1. 444 33532. The correct tool will do the job better and safer at the rate for which the tool is designed Disconnect the tool from the air source before making any adjustments changing accessories or storing the tool Such preventive safety measures reduce the risk of starting the tool unintentionally Page 2 For technical questions please call 1 800 444 3353 Keep bystanders children and visitors away while operating the tool Do not overreach Keep proper footing and balance at all times Proper footing and balance enables better control of the tool in unexpected situations Use safety equipment A dust mask non skid safety shoes and a hard hat must be used for the applicable conditions Always wear eye protection Wear ANSI approved safety goggles Store the tool when it is idle out of reach of children and other untrained persons A tool is dangerous in the hands of untrained users Item 69232 Tool Use and Care cont 4 Check for misalignment or binding of moving parts breakage of parts and any other condition that affects the tool s operation If damaged have the tool serviced before using Many accidents are caused by poorly maintained hose reels There is a risk of bursting if the tool is damaged Service 1 Tool service must be performed only by qualified repair personnel 2 When servicing a tool use only identical replacement parts Use only authorized parts Air Source 1 Never connect to
3. an air source that is capable of exceeding 200 psi Over pressurizing the tool may cause bursting abnormal operation breakage of the tool or serious injury to persons Use only clean dry regulated compressed air at the rated pressure or within the rated pressure range as marked on the tool Always verify prior to using the tool that the air source has been adjusted to the rated air pressure or within the rated air pressure range Safety Symbol Definitions PSI Pounds per square inch of pressure Property or statement NPT WARNING marking concerning Risk of Eye Injury Wear ANSI approved eye protection Specific Safety Instructions National pipe thread tapered 1 The warnings and precautions discussed in this manual cannot cover all possible conditions and situations that may occur It must be understood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator 2 Obey the manual for the air tool and air compressor used with this tool Use only accessories that are identified by the manufacturer for the specific tool model Use of an accessory not intended for use with the specific tool model increases the risk of injury to persons Use only the lubricants supplied with the tool or specified by the manufacturer Never use oxygen carbon dioxide combustible gases or any bottled gas as an air source for the tool Such gases are capable
4. of explosion and serious injury to persons ymbol Property or statement WARNING marking concerning Risk of Respiratory Injury Wear NIOSH approved dust mask respirator WARNING marking concerning Risk of Explosion Install an in line shutoff valve to allow immediate control over the air supply in an emergency even if a hose is ruptured WARNING The brass components of this product contain lead a chemical known to the State of California to cause birth defects or other reproductive harm California Health amp Safety code 25249 5 et seq A SAVE THESE INSTRUCTIONS Item 69232 For technical questions please call 1 800 444 3353 Page 3 SAFETY dNLas Functional Description Specifications Hose Length 250 PSI Air Inlet 1 4 18 NPT Components and Controls Mounting Plate Inlet from Compressor on Mounting A Plate Outlet to tool lt lt Handle Reel Flange Figure A Initial Hose Reel Setup Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product Note For additional information regarding the parts listed in the following pages refer to the Assembly Diagram near the end of this manual 1 Choose a mounting location that is free of electrical 3 Check for hidden wiring then drill holes to wiring or other obstructions and is sturdy enough acco
5. Owner s Manual amp Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions assembly operating inspection maintenance and cleaning procedures Write the product s serial number in the back of the manual near the assembly diagram or month and year of purchase if product has no number Keep this manual and the receipt in a safe and dry place for future reference CENTRALPNEUMATIC Air Hose Reel With 30ft Air Hose Visit our website at http www harborfreight com ITEM 69232 Email our technical support at tech harborfreight com When unpacking make sure that the product is intact and undamaged If any parts are missing or broken AWARNING please call 1 800 444 3353 as soon as possible Copyright 2012 by Harbor Freight Tools All rights reserved i i No portion of this manual or any artwork contained herein may be reproduced in Read this material before using this product any shape or form without the express written consent of Harbor Freight Tools Failure to do so can result in serious injury Diagrams within this manual may not be drawn proportionally Due to continuing SAVE THIS MANUAL improvements actual product may differ slightly from the product described herein Tools required for assembly and service may not be included wn gt m m lt WARNING SYMBOLS AND DEFINITIONS This is the safety alert symbol It is used to alert you to potential personal injury h
6. azards Obey all safety messages that follow this symbol to avoid possible injury or death Indicates a hazardous situation which if not avoided will result in death or serious injury Indicates a hazardous situation which if not avoided AWARNING ACAUTION CAUTION could result in death or serious injury Indicates a hazardous situation which if not avoided could result in minor or moderate injury Addresses practices not related to personal injury IMPORTANT SAFETY INSTRUCTIONS INSTRUCTIONS PERTAINING TO A RISK OF INJURY TO PERSONS WARNING When using hose reels basic precautions should always be followed including the following To reduce the risk of injury to persons read all the instructions before using the tool Work Area 1 Keep the work area clean and well lighted Personal Safety 1 Stay alert Watch what you are doing and use common sense when operating the tool Do not use the tool while tired or under the influence of drugs alcohol or medication A moment of inattention while operating the tool increases the risk of injury to persons Dress properly Do not wear loose clothing or jewelry Contain long hair Keep hair clothing and gloves away from moving parts Loose clothes jewelry or long hair increases the risk of injury to persons as a result of being caught in moving parts Tool Use and Care 1 Do not force the tool Use the correct tool for the application
7. e and an explanation of the complaint must accompany the merchandise If our inspection verifies the defect we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement We will return repaired products at our expense but if we determine there is no defect or that the defect resulted from causes not within the scope of our warranty then you must bear the cost of returning the product This warranty gives you specific legal rights and you may also have other rights which vary from state to state PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO CENTRAL 3491 Mission Oaks Blvd PO Box 6009 Camarillo CA 93011 800
8. mmodate the bolts not included to support the weight of the Reel and hose as well as the force used to extend and retract it Purchase four bolts able to support the same forces na Mount the Reel and secure in place with four bolts 5 Align the holes of the Handle with the holes on 2 Make a paper template from the mounting the Reel Flange and secure the Handle in place plate of the Reel Mark the center of the bolt with the three Screws Nuts and Washers holes in the desired mounting location Page 4 For technical questions please call 1 800 444 3353 Item 69232 Operating Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product Inspect tool before use looking for damaged loose and missing parts If any problems are found do not use tool until repaired General Operating Instructions 1 Attach a coupler sold separately to your air compressor hose and apply thread seal tape to the Inlet fitting on the Reel Connect the coupler to the Inlet fitting Connect your air tool to the other end of the Hose using another coupler and thread seal tape Follow all instructions from the air tool and compressor for set up and use When finished using the Hose disconnect the air tool and wind the hose Wipe the Hose Reel clean with a dry cloth Z Q lt oO Lu ou O Item 69232 For tech
9. nical questions please call 1 800 444 3353 Page 5 AONVNALNIVIN User Maintenance Instructions AWARNING TO PREVENT SERIOUS INJURY Detach air supply from this product before performing any inspection maintenance or cleaning procedures Procedures not specifically explained in this manual must be performed only by a qualified technician TO PREVENT SERIOUS INJURY FROM TOOL FAILURE Do not use damaged equipment If abnormal noise vibration or leaking air occurs have the problem corrected before further use Cleaning Maintenance and Lubrication Note These procedures are in addition to the regular checks and maintenance explained as part of the regular operation of the Hose Reel 1 BEFORE EACH USE inspect the general 2 AFTER EACH USE re wind the hose onto the reel condition of the tool Check for and wipe the Hose Reel clean with a dry cloth e loose hardware or housing e misalignment or binding of moving parts e cracked or broken parts and e any other condition that may affect its safe operation CENTRAL Page 6 For technical questions please call 1 800 444 3353 Item 69232 Parts List and Diagram Part Description Qty Part Description Qty 3 Spring washer __ _ J1 Nut 8 Washer _ y Oa Protector rubber 1 6 Flangea tC Clamp i O Screw o y y Oa 8 FlangeB tC Screw y O8 9 Positionsleeve _ 1 Washer __ y O8 Nut J33 3 Handle 1 24 _ Valve MAINTENANCE Reco
10. rd Product s Serial Number Here Note If product has no serial number record month and year of purchase instead Note Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts Item 69232 For technical questions please call 1 800 444 3353 Page 7 Limited 90 Day Warranty Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase This warranty does not apply to damage due directly or indirectly to misuse abuse negligence or accidents repairs or alterations outside our facilities criminal activity improper installation normal wear and tear or to lack of maintenance We shall in no event be liable for death injuries to persons or property or for incidental contingent special or consequential damages arising from the use of our product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS To take advantage of this warranty the product or part must be returned to us with transportation charges prepaid Proof of purchase dat
Download Pdf Manuals
Related Search