Harbor Freight Tools 2628 User's Manual
Contents
1. SKU 2628 Page 2 10 Stay alert Watch what you are doing use common sense Do not assemble the Cycle tree when you are tired 11 Check for damaged parts Before using this movable bicycle rack any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function Check for alignment and binding of moving parts any broken parts or mounting fixtures and any other condition that may affect proper operation Any part that is damaged should be properly repaired or replaced by a qualified technician 12 Replacement parts and accessories When servicing use only identical replacement parts Use of any other parts will void the warranty Only use accessories intended for use with this movable bicycle rack Approved accessories are available from Harbor Freight Tools 13 Do not assemble Cycletree if under the influence of alcohol or drugs Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs If there is any doubt do not assemble the Cycletree 14 Maintenance For your safety parts replacement or repair should be performed by a qualified technician 15 Maintain Balance To obtain the best and safest performance of the Cycletree be sure that the multiple hanging bicycles are evenly distributed on the Cycletree Be careful to follow the operation instructions on page 4 Warning The warnings cautions and instru2. 12 06
3. CYCLETREE Model 02628 ASSEMBLY and OPERATING INSTRUCTIONS Bicycle s not included Distributed Exclusively by fiz 3491 Mission Oaks Blvd Camarillo CA 93011 Visit our Web site at http www harborfreight com Copyright 2002 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools For technical questions and replacement parts please call 1 800 444 3353 Specifications Overall Dimensions 30 Square Base Top of T Bar is 66 from the Base Beam Hang Bar Dimensions 36 Height amp 17 1 2 Length per side 7 8 Diameter 1 3 16 Sq x 35 1 8 L x 1 16 Thick Center Post Dimensions 1 Sq x 36 L x 1 16 Thick 778 W x3 Diameter Save This Manual You will need the manual for the safety warnings and precautions assembly instructions operating and maintenance procedures parts list and diagram Keep your invoice with this manual Write the invoice number on the inside of the front cover Keep the manual and invoice in a safe and dry place for future reference Safety Warnings and Precautions WARNING When using the movable bicycle rack basic safety precautions should al ways be followed to reduce the risk of personal injury and damage to equipment Read all instructions before using this movable bicycle rack 1 Keep work area clean Clutt
4. Cycletree Maintain balance to obtain the best and safest performance of the Cycletree Be sure that the multiple hanging bicycles are evenly distributed on the Cycletree SKU 2628 Page 4 REV 12 03 REV 12 06 Maintenance 1 Periodically check that the hardware is tight Tighten if necessary Parts List artNo Description ss Q A OA Center Post 2A 3 Bolt M6 3A Bolt M8 Flat Washer 6 Flat Washer 8 Nut M6 Nut M8 lt 4A 5A 4 6 B8 is PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER NOR DISTRIBU TOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO NOTE Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts SKU 2628 Page 5 REV 12 03 12 06 Assembly Drawing SKU 2628 Page 6 REV 12 03
5. ctions discussed in this instruction manual cannot cover all possible conditions and situations that may occur It must be understood SKU 2628 Page 3 Assembly Refer to the Assembly Drawing on Page 6 1 Form a square by facing both of the Base Brackets 1 toward each other and inserting both of the Base Channeled Supports 2 into the Base Brackets 1 lining up the holes on all four corners 2 Put each of the Casters 3 through the holes on the four corners of the base frame you just constructed from the bottom so that the square frame sits on them 3 Place Strut A 6 on a top of the threaded caster bolt making sure the end with the most severe angle faces the middle of the square Refer to the Assembly Drawing on Page 6 Secure it with a Flat Washer 4 and Nut 5 4 On the opposite corner diagonal repeat step three with the other Strut A 6 5 On the two remaining corners repeat the process in step three above using both of the Struts B 8 6 Set the Base Beam 7 over the holes on the center of each of the Base Brackets 1 and secure it by putting a Bolt 13 in from the top and attaching a Flat Washer 14 and Nut 15 from the bottom on both sides Make sure that the square receptacle on the Base Beam 7 faces up 7 Slide the Base Post 9A through the flexible opening made by the top of the four Struts and insert it into the square receptacle on the Base Beam 7 8 Line up the top of all four Struts
6. ered areas invite injuries 2 Observe work area conditions Do not use Cycletree in damp or wet locations Don t expose to rain Keep work area well lighted Situate the Cycletree in a child safe location Only use the Cycletree on a flat level hard surface 3 Keep children away Children must never be allowed in the work area Do not let them handle the Cycletree Do not let children remove or add cycles to the Cycle tree 4 Store idle equipment When not in use Cycletree must be stored in a dry location to inhibit rust Always keep Cycletree out of reach of children 5 Use the right tool for the job There are certain applications for which this product was designed It will do the job better and more safely at the rate for which it was intended Do not modify this product and do not use this product for a purpose for which it was not intended 6 Dress properly Do not wear loose clothing or jewelry as they can be caught in moving parts Protective electrically non conductive clothes and non skid footwear are recommended when working Wear restrictive hair covering to contain long hair 7 Use eye protection Always wear ANSI approved impact safety goggles during assembly 8 Do not overreach Keep proper footing and balance at all times 9 Maintain this movable bicycle rack with care Keep Cycletree clean for better and safer performance The handles must be kept clean dry and free from oil and grease at all times
7. with the two connection holes on the Base Post 9A and secure both Struts A 6 with a Bolt 13 Flat Washer 14 and Nut 15 Next secure both Struts B 8 with a Bolt 13 Flat Washer 14 and Nut 15 9 Insert the Center Post 10A into the Base Post 9A and secure it with 2 Bolts 13A 2 Flat Washers 14A and 2 Nuts 15A The Center Post 10A has various holes for height adjustment 10 Slide the Plastic Covered T Bar 12A onto the top of the Center Post 10A and secure it with 2 Bolts 13A 2 Flat Washers 14A and 2 Nuts 15A Operation Warning Hanging and dismounting of bicycles should only be done by adults who are physically capable of safely handling and lifting the weight of a bicycle Hanging Bicycles Hang one bicycle by threading the front wheel spokes through the plasic covered T Bar the next bicycle must be hung the same way but facing the opposite direction see photos to the right and on front cover continue the same procedure making sure that all the contigious bicycles hang opposite to each other It is recommended that two people assist in hanging the bicycles to maintain the balance and stability of the Cycletree Dismounting Bicycles Before lifting the front wheel off the Plastic Covered T Bar 12A place a firm grip on the bicycle frame just behind the front fork making sure that the bicycle does not sway the wrong way and carefully remove the bicycle from the
Download Pdf Manuals
Related Search