Harbor Freight Tools 239 User's Manual
Contents
1. PITTSBURGHEZY TORQUE WRENCH 00239 00807 Models 00808 02696 ASSEMBLY AND OPERATING INSTRUCTIONS P Model 00239 1 2 Drive Torque Wrench shown above Visit our website at http www harborfreight com Read this material before using this product Failure to do so can result in serious injury SAVE THIS MANUAL Copyright 2009 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools Diagrams within this manual may not be drawn proportionally Due to continuing improvements actual product may differ slightly from the product described herein Tools required for assembly and service may not be included For technical questions or replacement parts please call 1 800 444 3353 Revised Manual 10i SAVE THIS MANUAL Keep this manual for the safety warnings and precautions assembly operating inspection maintenance and cleaning procedures Keep this manual future reference CAUTION without CAUTION the safety alert symbol is used to address practices not related to personal injury warnings and instructions and the receipt in a safe and dry place for WARNING Read all safety IMPORTANT SAFETY INFORMATION In this manual on the labeling and all other information provided with this product This is the safety alert symbol It is use2. d to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death DANGER indicates 2 rN DANGER a hazardous situation which if not avoided will result in death or Failure to follow the warnings and instructions may result in serious injury Save all warnings and instructions for future reference The warnings cautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur It must be understood by operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator Wear ANSI approved safety goggles and heavy duty work gloves during use serious inju 3 Use only within rated torque range Ous ary Do not use for loosening AWARNING oe 4 Use as intended only Do not use situation which if not as hammer or pry bar Do not use a ebes result ini death handle extension to increase force lean A i a Do not drop or serious injury CAUTION used 5 Inspect before every use do not use ACAUTION with the safety aleit if damaged or parts loose symbol indicates a 6 Keep away from children hazardous situation which if not avoided could result in For your safety service calibration minorar moderate injury and maintenance should be performed regularly by a qualified NOTICE is used to technician NOTICE address prac
3. den at this point b Continue turning the knurled handle about a half turn clockwise until the 5 graduation mark lines up with the centerline It is now set for 55 See illustration B above Page 3 7 Retighten Lock Knob by turning it all the way clockwise Direction Switch 8 Set the Direction Switch for clockwise or counterclockwise operation The Switch shown above is in position for clockwise operation 9 Place socket onto the nut or bolt and pull handle gradually until a click is heard or felt Do not pull beyond that point the click indicates that the torque setting has been reached 10 Stop pulling and the Torque Wrench will automatically reset 11 When finished set the Torque to the lowest torque setting not lower than the lowest setting before storing indoors out of reach of children CLEANING MAINTENANCE AND LUBRICATION TO PREVENT ACAUTION INJURY FROM TOOL FAILURE Do not use damaged equipment If abnormal noise or vibration occurs have the problem corrected before further use 1 BEFORE EACH USE inspect the general condition of the tool Check for loose hardware misalignment or binding of moving parts cracked or broken parts and any other condition that may affect its safe operation 2 Ifthe Torque Wrench has not been used for some time turn the knurled Torque Wrenches a For technical questions please call 1 800 444 3353 handle CW and CCW sev
4. eral times to re lubricate the internal workings Then operate at a low torque setting several times This ensures proper operation Do not turn knurled handle below the lowest torque setting Wipe Torque Wrench with a cloth to clean Do not immerse in any cleaning solution This would damage the internal lubrication The Torque Wrench was calibrated and tested to 4 Periodically have the Wrench calibrated and serviced by a qualified technician Store inside case in a clean and dry location Note Replacement parts are not available for this item Page 4
5. tices not related to personal injury Use only sockets with the correct drive and rated to at least the torque that will be applied to it Torque For technical questions please call 1 800 444 3353 Page 2 Wrenches SPECIFICATIONS Model_____ _02696 20 200 in Ib 1 4 11 4 Model 00239 00808 UNPACKING When unpacking make sure that the item is intact and undamaged If any parts are missing or broken please call Harbor Freight Tools at 1 800 444 3353 as soon as possible OPERATING INSTRUCTIONS SAFETY INFORMATION section at the beginning of this manual before set up or use of this product 1 Read the ENTIRE IMPORTANT 1 Wear ANSI approved safety goggles and heavy duty work gloves 2 Clean and or repair the threads that will be tightened Damaged or dirty threads will result in a misleading torque reading 3 Select the desired socket and verify it fits properly on the nut or bolt being tightened 4 Press the socket firmly onto the drive anvil Torque Wrenches For technical questions please call 1 800 444 3353 Lock Knob Turn the Lock Knob at bottom of the Handle counterclockwise until it stops Turn the handle to set the torque To set to 55 for example a Turn the knurled handle CW or CCW until the O graduation on the bevel edge lines up with 50 See illustration A above The 50 line is shown in grey because it will likely be hid
Download Pdf Manuals
Related Search