Harbor Freight Tools 1118 User's Manual
Contents
1. Next thread the Air Regulator 3B onto the Nipple 1B See Figure 2 below 2 Thread in the Air Valve 5B into the Air Regulator Assembly See Figure 3 gt gt Figure 2 Figure 3 3 Thread the Regulator Handle 1C into the Air Regulator 3B until tight See Figure 4 When assembly is complete it should look like the photo in Figure 5 below Figure 4 Figure 5 SKU 1118 For technical questions please call 1 800 444 3353 Page 4 Air Connections Caution To avoid injury make certain that the air compressor is unplugged from the power source and that all pressure is released from its tank before connecting the Air Filter Regulator to it 1 Connect the compressor air output hose not included or pipe not included to the Air Inlet 7B and securely tighten See Figure 6 below 2 Connect the air output hose to the Quick Coupler not supplied and screw into the Air Valve 5B and securely tighten See Figure 6 below 3 Connect air tool or devise to an output hose See Figure 6 below Air Input Hose Air Inlet 7B QUICK QUICK CONNECTOR CONNECTOR AIR COMPRESSOR sa Bow yes va e AIR TOOL b a gt DO oe OR DEVICE Air Output Hos e QUICK Regulator Handle 1C SAN uck COUPLER n COUPLER Pressure Gauge 6B Figure 6 Operation 1 Turn on the air compressor and check for leaks If any are found turn the Compressor off drain air from tank and fix the leak WARNING Do no exc2. and if damaged have them repaired by an authorized technician The Filter Regualtor must be kept clean dry and free from oil and grease at all times Disconnect power Unplug air compressor not included when not in use SKU 1118 For technical questions please call 1 800 444 3353 Page 2 11 12 13 14 15 16 17 18 Do not exceed maximum air pressure of 160 PSI Avoid unintentional starting Do not carry any air tool with your finger on the trigger whether it is plugged in or not Stay alert Watch what you are doing use common sense Do not operate any tool when you are tired Check for damaged parts Before using Filter Regulator any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function Check for alignment and binding of moving parts any broken parts or mounting fixtures and any other condition that may affect proper operation Any part that is damaged should be properly repaired or replaced by a qualified technician Do not use any air tool if its switch does not turn On and Off properly Replacement parts and accessories When servicing use only identical replacement parts Use of any other parts will void the warranty Do not operate air tools if under the influence of alcohol or drugs Read warning labels if taking prescription medicine to determine if your judgment or reflexes are impaired while taking drugs If there is any doubt do
3. CENTRAL PNEUMATIC _ Qe o a AIR FILTER REGULATOR ASSEMBLY AND OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd Camarillo CA 93011 Visit our Web site at http www harborfreight com Copyright 2006 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools For technical questions and replacement parts please call 1 800 444 3353 Specifications es e Air Inlet and Outlet Size Inlet 1 2 NPT 11 3 4 Tall x 3 7 8 DIA x 8 3 4 Deep Save This Manual You will need the manual for the safety warnings and precautions assembly instructions operating and mainte nance procedures parts list and diagram Keep your invoice with this manual Write the invoice number on the inside of the front cover Keep the manual and invoice in a safe and dry place for future reference Safety Warnings and Precautions WARNING When using tools basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment Read all instructions before using this tool 1 2 10 Keep work area clean Cluttered areas invite injuries Observe work area conditions Do not use in damp or wet locations Don t expose to rain Keep work area well lighted Do not use in the presence of flammable gases or liquids Keep children away Childre
4. ED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTI FIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACE MENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO SKU 1118 For technical questions please call 1 800 444 3353 Page 7 SKU 1118 WARRANTY LV RZN V Y YDAN YP D IN EX AWS S N A __ aa AZ CZN gt A lt _ os F gt AZ CZA VINA ZZN SN K PS A CENTRAL PNEUMATIC Y zA KA YV CM g yY WARRANTY K SY SX NS Z H Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards Ye Y f yy DAP and warrants to the original purchaser that this product is free from defects in materials and workmanship for the KZZ lt KN period of one year from the date of purchase This warranty does not apply to damage due directly or indirectly FX AN to misuse abuse negligence or accidents repairs or alterations outside our facili
5. eed 160 PSI during use 2 With the compressor ON turn the Adjusting Screw 1C to set the pressure that you want Look at the Pressure Gauge 6B while you turn the Adjusting Screw Stop turning the Regulator Handle 1C when the Presure Gauge needle points to the desired pressure See Figure 6 3 You must drain the Air Filter Regulator of water daily With the unit under pressure turn the Drain Plug 14A to expel any accumulated moisture from the Air Filter See page 6 parts list A Maintenance 1 Periodically disassemble the Air Filter and remove all dirt and debris Remove air pressure before cleaning 2 Periodically remove the Filter 6A rinse it out with water and replace If it is damaged or if it needs to be replaced you can order a new one by calling 1 800 444 3353 and order SKU 10767 Filter Element SKU 1118 For technical questions please call 1 800 444 3353 Page 5 1B Nipple B Ebow BB Ar Regulator BP ss arve e eas PART A ea Frere Ba Ar Regulator r e saoo arva NOTE Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts SKU 1118 For technical questions please call 1 800 444 3353 Page 6 Spring Spring Seal NOTE Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts PLEASE READTHE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVID
6. lo CA 93011 800 444 3353 A SS n Ee ACIS ICIS YC IRS ICIS SS yy ANS INAV AAN ANAY SEINE SEINE ANAAA NZI ANS ANS For technical questions please call 1 800 444 3353 Page 8
7. n must never be allowed in the work area Do not let them handle this product or other machines tools or extension cords Store idle equipment When not in use this product must be stored in a dry location to inhibit rust Always lock up and keep out of reach of children Use the right tool for the job Do not attempt to force a small tool or attachment to the work of a larger industrial tool There are certain applications for which this product was designed It will do the job better and more safely at the rate for which it was intended Do not modify this product and do not use this product for a purpose for which it was not intended Do not overreach Keep proper footing and balance at all times Do not reach over or across running machines Dress properly Do not wear loose clothing or jewelry as they can be caught in moving parts Protective electrically nonconductive clothes and nonskid footwear are recommended when working Wear restrictive hair covering to contain long hair Use eye and ear protection Always wear ANSI approved impact safety goggles when using and servicing this product and or air tools Wear a full face shield if you are producing metal filings or wood chips Wear a NIOSH approved dust mask or respirator when working around metal wood and chemical dusts and mists Maintain tools with care Keep clean for better and safer performance Follow instructions for lubricating and changing accessories Inspect periodically
8. not operate the product Maintenance For your safety service and maintenance should be performed regularly by a qualified technician Before using any air tool read and adhere to all instructions and safety warnings provided in the instruction manual of the air compressor being used Be sure to use compressed air only Warning The brass components of this product contain lead a chemical known to the State of California to cause birth defects or other reproductive harm California Health amp Safety Code 25249 5 et seq Warning The warnings cautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur It must be understood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the opera tor Unpacking When unpacking check to make sure all parts are included Refer to the photo below and the Parts List and Diagram located at the end of this manual If any parts are missing or broken please call Harbor Freight Tools at the number on the cover of this manual Assembly Remove the contents in the small plastic bag and locate Nipple 1B Thread the Nipple 1B into the Plug 1A You should use teflon tape or pipe dope not included on all threaded connections See Figure 1 below Figure 1 SKU 1118 For technical questions please call 1 800 444 3353 Page 3 Assembly Continued 1
9. ties or to lack of maintenance A L CS Ve shall in no event be liable for death injuries to persons or property or for incidental contingent special or NA gt Jj ae Me ae a SN consequential damages arising from the use of our product Some states do not allow the exclusion or limitation YX x of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS VA Seg WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING lt AY THE WARRANTIES OF MERCHANTABILITY AND FITNESS NY MAY D4 A To take advantage of this warranty the product or part must be returned to us with transportation charges prepaid as Z Proof of purchase date and an explanation of the complaint must accompany the merchandise If our inspection UD MLA verifies the defect we will either repair or replace the product at our election or we may elect to refund the purchase Zo Ni price if we cannot readily and quickly provide you with a replacement We will return repaired products at our Ney AN expense but if we determine there is no defect or that the defect resulted from causes not within the scope of Y our warranty then you must bear the cost of returning the product va A VPS KA This warranty gives you specific legal rights and you may also have other rights which vary from state to state AS CZ RSS AG 3491 Mission Oaks Blvd PO Box 6009 Camaril
Download Pdf Manuals
Related Search