Harbor Freight Tools 10 Ft. x 20 Ft. Portable Car Canopy Product manual
Contents
1. 10 Assembly 1 5 e 4 LEE 12 a Harbor Freight Tools Brand WARNING SYMBOLS AND DEFINITIONS This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death A DANGER Indicates a hazardous situation which if not avoided will result in death or serious injury AWARNING Indicates a hazardous situation which if not avoided could result in death or serious injury ACAUTION Indicates a hazardous situation which if not avoided could result in minor or moderate injury NOTICE CAUTION Addresses practices not related to personal injury WARNING marking concerning Risk safety goggles with side shields NY a set up and or use i Page 2 For technical questions please call 1 800 444 3353 Item 69034 IMPORTANT SAFETY INFORMATION AWARNING Read all safety warnings and instructions Failure to follow the warnings and instructions may result in serious injury Save all warnings and instructions for future reference The warnings precautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur It must be understood by the operator that common sense Z and caution are factors which cannot be built into this product but must be supplied by the operator Ww LL lt Assembly Precautions o 1 Do not assemble in windy condition2. MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO Record Products Serial Number Here Note If product has no serial number record month and year of purchase instead Note Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts a Harbor Freight Tools Brand Item 69034 For technical questions please call 1 800 444 3353 Page 9 MAINTENANCE AONVNALNIVIN Parts List and Diagram Parts List Note Individual part illustrations not to scale 40 1 4 Swaged Tube 24 Rafter Tube 40 5 8 Straight Cross Tube 3 Way Connector 4 Way Connector Base Fastening Stake Foot Plate Roof Tarp Ball Tie down Tarp Corner Rope and Hook Rope Fastening Stake Page 10 For technical questions please call 1 800 444 3353 Item 69034 Asse
3. for a replacement A SAVE THESE INSTRUCTIONS Specifications Center Height Side Height 6 3 Item 69034 For technical questions please call 1 800 444 3353 Page 3 AMIGWASSV Assembly Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product TO PREVENT SERIOUS INJURY Do not leave this product partially assembled Assemble this product completely at one time Note For additional information regarding the parts listed in the following pages refer to Parts List and Diagram on page 10 Note Much of this product s assembly is done using slip fit construction Make sure all parts seat completely and securely Arubber mallet sold separately can be used to gently tap parts in place to ensure a tight fit Sk y P SS X 1 Assemble one half of the roof using 11x Swaged Tubes 2 3x Rafter Tubes 3 4x Straight Cross Tubes 4 4x 3 Way Connectors 5 and 2x 4 Way Connectors 6 Align the 3 and 4 Way Connectors so that the free ends are all on the same side of the assembly as shown in Figure 1 Figure 2 Roof Assembly 2 2 Connect a Swaged Tube 2 to each 3 and 4 Way Connector 5 6 at the top of the roof Connect a Rafter Tube 3 to the end of each Swaged Tube 2 Connect 4x Swaged Tubes 2 2x Straight Cross Tubes 4 2x 3 Way Connectors 5 and 1x 4 Way Connector 6 together then attac
4. we cannot readily and quickly provide you with a replacement We will return repaired products at our expense but if we determine there is no defect or that the defect resulted from causes not within the scope of our warranty then you must bear the cost of returning the product This warranty gives you specific legal rights and you may also have other rights which vary from state to state a Harbor Freight Tools Brand 3491 Mission Oaks Blvd PO Box 6009 Camarillo CA 93011 800 444 3353
5. Owner s Manual amp Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions assembly operating inspection maintenance and cleaning procedures Write the product s serial number in the back of the manual near the assembly diagram or month and year of purchase if product has no number Keep this manual and the receipt in a safe and dry place for future reference iiB uoo GANOPY a Harbor Freight Tools Brand EHE TEE LET l KN f NAR Visit our website at http www harborfreight com Email our technical support at tech harborfreight com ITEM 69034 When unpacking make sure that the product is intact and undamaged If any parts are missing or broken AWARNING please call 1 800 444 3353 as soon as possible Copyright 2012 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in Read this material before using this product any shape or form without the express written consent of Harbor Freight Tools Failure to do so can result in serious injury Diagrams within this manual may not be drawn proportionally Due to continuing SAVE THIS MANUAL improvements actual product may differ slightly from the product described herein Tools required for assembly and service may not be included ALAAVS Table of Contents SI Em 2 Maintenance sseee 8 SPECHICATIONS MERE 3 Parts List and Diagram
6. h that assembly to the ends of the Rafter Tubes 3 Page 4 For technical questions please call 1 800 444 3353 Item 69034 eyelet Figure 3 Roof Tarp 9 3 Place the Roof Tarp 9 over the top of the roof assembly with its eyelet straps facing down on the inside Figure 4 Connecting Ball Tie downs 10 4 Use the Ball Tie downs 10 to attach the Roof Tarp to the tubes using the eyelets on the eyelet straps gt a LLI o o lt Figure 5 Leg Assembly 1 5 Attach a Straight Tube 1 to each 3 and 4 Way Connector 5 6 on one side of the assembly Note The warning label is on one of the Straight Tubes 1 Turn that Tube so that the Warning label can be read easily Attach a Swaged Tube 2 to the bottom of each Straight Tube Item 69034 For technical questions please call 1 800 444 3353 Page 5 A1aNassv Figure 6 Leg Assembly 2 6 Attach a Straight Tube 1 to each 3 and 4 Way Connector 5 6 on the other side of the assembly Attach a Swaged Tube 2 to the bottom of each Straight Tube Figure 7 Foot Plate 8 Assembly 7T Place a Foot Plate 8 over the bottom of each Swaged Tube 2 Use two Base Fastening Stakes 7 through each Foot Plate to anchor the Canopy Note Verify that there are no utility lines nearby before driving anchors Page 6 For technical questions please call 1 800 444 3353 Item 69034 Figure 8 Securing Tarp Corner Ho
7. mbly Diagram MAINTENANCE Item 69034 For technical questions please call 1 800 444 3353 Page 11 Limited 90 Day Warranty Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase This warranty does not apply to damage due directly or indirectly to misuse abuse negligence or accidents repairs or alterations outside our facilities criminal activity improper installation normal wear and tear or to lack of maintenance We shall in no event be liable for death injuries to persons or property or for incidental contingent special or consequential damages arising from the use of our product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS To take advantage of this warranty the product or part must be returned to us with transportation charges prepaid Proof of purchase date and an explanation of the complaint must accompany the merchandise If our inspection verifies the defect we will either repair or replace the product at our election or we may elect to refund the purchase price if
8. ok 11 8 For each corner of the Roof Tarp 9 a Connect the Tarp Corner Hook 11 to the hole on the inside corner of the Straight Tube 1 b Pull the end of the Rope snug and tie it off a a Lu o lt LA Figure 9 Rope Fastening Stakes 12 9 Drive a Rope Fastening Stake 12 about 3 feet away from each corner of the canopy angled inward Tie a Rope 13 around the 3 Way Connector 5 at each corner of the Canopy then attach it to the Stake 12 Note Verify that there are no utility lines nearby before driving anchors Item 69034 For technical questions please call 1 800 444 3353 Page 7 NISI EI Maintenance AWARNING TO PREVENT SERIOUS INJURY FROM PRODUCT FAILURE Do not use damaged products If damage is noted have the problem corrected before further use Procedures not specifically explained in this manual must be performed only by a qualified technician MONTHLY inspect the general condition of the Portable Garage Check for loose ratchet tie downs anchors tube connections and rail clamps tighten as needed torn or frayed covers ropes or cables cracked bent or broken parts and any other condition that may affect its safe operation a Harbor Freight Tools Brand Page 8 For technical questions please call 1 800 444 3353 Item 69034 PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS
9. s 5 Keep assembly area clean and well lit 2 Assemble and install only on 6 Keep bystanders out of the area during assembly flat level hard surface T Do not assemble when tired or when under 3 Assemble and anchor only according to the influence of drugs or medication these instructions Improper assembly or T inadequate anchoring can create hazards 8 Product capabilities apply to properly and completely assembled product only 4 Wear ANSI approved safety goggles and heavy duty work gloves during assembly Use Precautions 1 Do not use grill or any other type of 5 Use as intended only fire under cover Cover may catch fire Do not use for long term shelter if exposed to heat rising from fire 6 Inspect regularly tighten all loose hardware and 2 Do not allow snow or debris to loose cords and secure all loosened anchors accumulate on this item If any parts are damaged bent or stretched they must be replaced Hardware may loosen during 3 Heavy wet snow or strong wind could cause normal operation stresses Loose hardware damage or sudden collapse Remove the Cover or damaged altered parts will compromise when these or similar conditions are expected the structural integrity of this product 4 This product is not a toy Do not allow 7 Maintain product labels and nameplates children to play with or near this item These carry important safety information If unreadable or missing contact Harbor Freight Tools
Download Pdf Manuals
Related Search