Harbor Freight Tools 1/2 In Picket Twister Attachment Product manual
Contents
1. 12 13 14 15 SECURE WORK Use clamps or a vise to hold the work if possible It s safer than using your hands and it frees both hands to operate the tool DO NOT OVERREACH Keep proper footing and balance at all times MAINTAIN TOOLS WITH CARE Keep tools sharp and clean for better and safer performance Follow instructions for lubricating and changing accessories Keep handles dry clean and free from oil and grease STAY ALERT Watch what you are doing use common sense Don t operate any tool when you are tired CHECK DAMAGED PARTS Before using any tool any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function Check for alignment of moving parts binding of moving parts breakage of parts mounting and other conditions that may affect its operation Any part that is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated elsewhere in the instruction manual REPLACEMENT PARTS AND ACCESSORIES When servicing use only identical replacement parts Only use accessories intended for use with this tool Approved accessories are available from Harbor Freight Tools DO NOT OPERATE TOOL IF UNDER THE INFLUENCE OF ALCOHOL OR DRUGS Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs If there is any doubt do not operate machine UNPACKING2. When unpacking refer to the list below If any parts are missing or broken please call Harbor Freight Tools at the number on the cover of this manual NO _TTEMDESCRIPTION ow 6 Tower Frame Depth Stop Depth Stop Lock Knob 06 FrameBoltKnob 1 09 Page 3 SKU 36620 ASSEMBLY Step 1 Using the FRAME BOLT 07 and FRAME BOLT KNOB 08 attach the LOWER FRAME 06 to the bottom of the STAND 11 of the Compact Bender See Figure 1 Step 2 Insert the DEPTH STOP 09 into the round hole of the LOWER FRAME 06 and attach using the DEPTH STOP LOCK KNOB 10 Stand u Frame Bolt i b Knob 08 7 Frame i Bolt 07 Lower Frame 06 Depth Stop Lock Knob Depth Stop 10 09 Figure 1 Lower Frame Assembly Page 4 SKU 36620 Step 3 Attach the BRACKET 05 to the RING ASSEMBLY DIE RECEIVER 10 of the Compact Bender using two LONG PINS 1 Use Holes 5 amp 6 See Figure 2 Step 4 Insert the HANDLE 01 into the BRACKET 05 ue Long Handle 01 Pin Ring Assembly Bracket Die Receiver 05 i Figure 2 Handle Head Assembly Page 5 SKU 36620 OPERATIONS Step 1 Determine the length of stock you wish to twist and cut it accordingly Step 2 Determine the length of stock you wish to leave unbent on either end and mark using chalk Step 3 Insert stock through the square holes of the HANDLE 01 and the LOWER FR
3. INSTRUCTIONS BEFORE USING THIS TOOL 1 KEEP WORK AREA CLEAN Cluttered areas invite injuries 2 CONSIDER WORK AREA CONDITIONS Don t use in damp wet or poorly lit locations Do not expose to rain Keep work area well lit 3 KEEP CHILDREN AWAY All children should be kept away from the work area Don t let them handle machine 4 STORE IDLE EGUIPMENT When not in use tools should be locked up in a dry location to inhibit rust If possible store in an area out of reach of children 5 DO NOT FORCE THE MACHINE OR TOOL It will do the job better and more safely at the rate for which it was intended 6 USE THE RIGHT TOOL Don t force a small tool or attachment to do the work of a larger industrial tool Don t use a tool for a purpose for which it was not intended 7 DRESS PROPERLY Don t wear loose clothing or jewelry They can be caught in moving parts Protective gloves and non skid footwear are recommended when working Wear restrictive hair covering to contain long hair preventing it from getting caught in machinery 8 USE EYE AND EAR PROTECTION Use a full face mask if the work you re doing produces metal filings dust or wood chips Goggles are acceptable in other situations Wear a clean dust mask if the work creates a lot of fine or coarse dust When operating for extended periods of time use approved ear protection Safety goggles and ear protectors are available from Harbor Freight Tools Page 2 SKU 36620 10 11
4. AME T06 See Figure 3 Handle 01 Stock oN og Lower Frame 06 WARNING Depth Stop Never let the HANDLE go until you have Lock Knob finished the twisting operation When 10 letting the HANDLE go be careful as it 10 may spring back due to the torque of the twisting action Depth Stop 09 Figure 3 Operation Page 6 SKU 36620 Step 4 Adjust the DEPTH STOP 09 so that the chalk mark is even with the top of the LOWER FRAME 06 when the stock is resting on the DEPTH STOP S foot Secure the DEPTH TOP 09 using the DEPTH STOP LOCK KNOB 10 Step 5 Rotate the handle either clockwise or counterclockwise depending upon the desired direction of the twist Step 6 Continue rotating the handle until you have the desired twist Step 7 The length of your stock will not change even as you twist PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUME
5. S ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO Page 7 SKU 36620 PARTS LIST PART NO DESCRIPTION 09 Depth Stop 10 Depth Stop Lock Knob 1 06 8 10 1 ASSEMBLY DIAGRAM Page 8 SKU 36620
6. TWISTING ATTACHMENT FOR 31980 EE 36620 ASSEMBLY AND OPERATING INSTRUCTIONS Visit our website at http www harborfreight com Read this material before using this product Failure to do so can result in serious injury SAVE THIS MANUAL Copyright 1997 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools Diagrams within this manual may not be drawn proportionally Due to continuing improve ments actual product may differ slightly from the product described herein Tools reguired for assembly and service may not be included For technical guestions or replacement parts please call 1 800 444 3353 Revised Manual 11b SPECIFICATIONS ITEM 36620 Capacity 1 2 Pickets 36 Long Metal Type Hot Rolled Square Mild Steel 25x 1 14 SAVE THIS MANUAL You will need this manual for the safety instructions operating instructions and parts list Put it in a safe dry place for future reference Keep your invoice with this manual Write the invoice number on the inside front cover READ ALL INSTRUCTIONS BEFORE ASSEMBLING OR OPERATING THIS TOOL SAFETY WARNINGS 8 CAUTIONS WARNING When using electric tools machines or eguipment basic safety precautions should always be followed to reduce the risk of fire electric shock and personal injury READ ALL
Download Pdf Manuals
Related Search