Haier XQG50-ABA1100CTX User's Manual
Contents
1. Caution 1 Do not add liquid detergent to compartment 1 and 2 2 For pre washing program detergent should be added to both compartments 1 and 2 For other programs do not add detergent to compartment 1 3 Do not overuse softener otherwise it will damage the synthetic fibers 3 Select washing program For optimal wash results select the most suitable washing program The washing program instructions are printed on the detergent drawer Caution 1 Never select a washing program before the power is switched off 2 For washing chemical or woolen goods the laundry will go through a water soaking cycle before the spinning and drainage programs If some expensive clothes and articles should be removed select the drainage program manually Chemical or woolen goods are prone to crease if not taken out soon after washing is finished 3 For washing chemical fabrics if the drying option is selected the washing process will skip the soaking phase and commence drying Washing methods 4 Washing temperature setting Set the washing temperature as reguired otherwise set at position when heating is not needed Refer to the Program Selection for maximum temperature allowed for each washing procedure 5 Drylng options setting 1 The drying time can be selected in between 0 120 minutes for high temperature drying for low temperature drying it can be selected from 0 80 minutes 2 When the washing machine is loaded in excess of its2. drying capacity set the drying select knob at the position 0 Sort out the laundry into types after washing and carry out drying in batches 3 Avoid drying woolen goods 4 Keep the water supply turned on to condense vapour from the drying process 6 Selecting the function button Select function button as required refer to the directions printed on the operation panel otherwise keep all the buttons released 7 Washing Press the power button and the washing machine will automatically commence the programmed washing process 8 End Wait 2 3 minutes after the washing process is finished press the power button again to cut off the power supply Open the door to take out the laundry Turn off the tap and unplug the washing machine Additional information Energy time and water saving during wash process 1 Collect clothes for one full wash load Do not overload the washing machine Pre wash heavily soiled clothes Reduce the amount of detergent or choose fast or minimal washing programs for lightly soiled clothes dirty Choose a proper washing temperature Only exceed 60 C for heavily soiled clothes Do not use more detergent than required Softener makes clothes feel softer and easier to iron Washing methods 8 Set the drying time shorter than you anticipate Open the door and feel whether the laundry is sufficiently dry If not continue the drying for a short time This can save energy and the clothes w
3. Haier Fully Automatic Front Loading Washer Dryer XQG50 ABA1100CTX Content Before Use Names of Parts Safety and Precaution Installation Control Panel Operational Functions About Wash Programmes Program Selection Preparation Washing Methods Maintenance Maintenance Trouble shooting Specifications Wiring circuit OPERATION MANUAL Please carefully read this operation manual before using the product and please well keep this operation manual for your later reference Names of Parts re MERI EL st C Detergent Drawer Top Drying Knob Programming Knob Temperature Knob Door Watch Glass Door Knob _ Fs Power Supply Cable E Back Plate Screw 3 Packing Bolt 3 Drainage Hose Back Plate N cam and Warning Symbols Definitions For your safety any instructions in T this manual with this Warning sign shall be strictly followed For your safety and to prevent damages to the washing machine any instruction in this manual with this Stop sign shall be strictly followed Safety and Precaution Please well connect the earth line of socket to avoid electric shocking by accidental leakage Do not wash the clothes with kerosene gasoline alcohol and other flammable materials Do not put such substances near the machine Do not allow children to play with the packing materials after unpacking Please do not pull the electric cord when pulling out the plu
4. ake the water inlet hose nut to see if yp it is tightly and properly fixed Connector of water inlet valve Water drainage hose The height of the terminal of the water drainage hose should be between 80cm 100cm from the bottom of the machine the water drainage hose must be securely placed on the clip on the back of the washing machine Use the water drainage support supplied as an accessory for proper installation of the water drainage hose Fix the water drainage hose support with waterproof string Do not use an excessively long water drainage hose and contact the Shun Hing Electric Service Centre Ltd if the water drainage hose needs to be extended The water drainage hose should not be extended more than 250cm longer extension will result in concurrent water inflow and outflow The diameter of the extension hose should be the same as the original hose Caution water drainage hose must not be immersed in water the original and extension hoses should be tightly connected Connection of power supply Check the following items before connect to the power supply The socket conforms to the maximum power load The maximum current load of the socket and power supply cable should not be less than 15A Power supply voltage conforms to the required value Check whether the power supply socket and the plug of the washing machine are compatible if they are not compatible Pl
5. art working release this button the washing machine will stop No spin button Push the button down the washing machine does not spin and only perform the drain Use this function when the clothes are difficult to iron or only can use chemical fiber and soft washing program Half load button Pressing this button will reduce the consumption of water during bleaching under intense wash It is recommended that this program be used when doing 1 2 a small laundry load Do not forget to reduce the amount of detergent used Power light The light will illuminate when the power supply is connected Spin speed button In the cotton cycle you can change the spin speed 650rpm or 1100rpm to satisfy your needs For synthetic cycle the spin speed 500rpm or 850rpm can be selected Program Selection Note O indicates that softener can be added if needed x indicates that detergent must be added X indicates that detergent must not be added Remark Due to different washing laundry the temperature and programmes selected are different This table is for reference only Recommended Det t Recommended Max etergen Program Laundry Temperature SC 1 2 3 4 Pre wash 1 Heavy soiled white laundry 40 x O Xx O Normal wash 2 White and fast colours Max x x O O o Quick wash 3 White and fast colours soiled 60 x x O O Oo g super Quick 4 Delicate c
6. e materials Do not open the detergent box during the wash cycle After washing turn off the tap to prevent leakage unplug the washing machine and wipe clean the lower part of the port hole Keep the door slightly open when the washing machine is not being used Never cover the machine with a plastic sheet Installation O As shown in Figure 1 remove all the packing materials including the foam base Remove the packing screws as shown in Figure 2 The packing bolts protect the appliance from shock during transportation The steps below should be followed before using the appliance Remove the rear panel of the washing machine Remove the three packing bolts from the rear panel of the washing machine the rubber hose and then the shock absorption channel steel Reinstall the back plate Fill the holes left by the packing bolts with plastic plugs Attention the packing bolts and rubber hose should be kept in a safe place for later use O Adjusting the position of the washing machine There are adjustable feet under the bottom of the washing machine Before use the washing machine should be adjusted as shown in Figure 3 so that it is balance Figure 3 Installation Connection of water inlet hose and washing machine Water inlet hose nut 5 1 Place the water inlet hose nut on the connector of the water inlet valve 1 2 Slightly sh
7. ease contact Shun Hing Electric Service Centre Ltd for power cable replacement The washing machine should be connected to an earth before use Supplementary earth cable should not be necessary if the socket is connected to the earth Control Panel Washing program select knob Turn the knob clockwise to set the desired wash program Refer to the Program Selection Caution Turn off the power and turn the program knob clockwise for setting desired wash program Washing temperature select knob Turn the knob clockwise to set the desired water inlet temperature Temperature between 30 C Max or 30 C 60 C can be selected Refer to the Program Selection Cold wash is selected when the knob is set at Drying select knob This knob is for selecting a drying program 0 120 minutes for cotton fabrics and coarse fibre fabrics 0 80 minutes for synthetic fabrics When a drying program finishes the washing machine stops drying and cools down Operational Functions Detergent drawer Compartment 1 Pre wash detergent Compartment 2 Standard wash detergent extra fast wash detergent Compartment 3 Softeners conditioners perfumes Compartment 4 Bleach This drawer is small and removable Note When bleaching place compartment 4 into compartment 1 remove this compartment when the pre washing program is chosen Power button Press this button washing machine will st
8. g 4 Please do not pull out or insert the plug with wet hands to avoid electric shocking Young children should be supervised to ensure that they do not play with the appliance or peer over the wash tub Do not touch the inside of door if it is opened during the drying process Safety and Precaution Please do not install the machine in damp exposed area or bathroom to avoid electric shocking catching fire faults and distortion accidents Keep away from heat sources and direct sunlight to prevent plastic and rubber components from aging Please ensure that the hose connection and the tap is opened before washing clothes The washing machine should be placed in a well ventilated area maintaing a space between walls or furniture During installation ensure that the electric cable is not trapped by the washing machine and avoid damage to the electric After switching the power off turn the program knob clockwise to set washing program Safety and Precaution Do not climb up or place any weight on the washer Before washing do up zippers buttons laces and repair damaged areas underwear or small articals should be placed in the laundry bag or a pillowslip The door is fitted with a self lock device and will not open until 2 3 minutes after the washing machine stops Do not force the door open Do not open the door when water level reaches the port hole Do not wash foam rubber or similar spong
9. ill not be over dried and difficult to iron 9 Refer to the following diagram for economical drying If the load is smaller than listed in the diagram reduce the time proportionally When the drying process finishes the program will end automatically Weight kg Cee Synthetic Clothes fabrics Range for drying time min Drying time min 75 85 90 100 Drying extent 0 120 120 130 50 60 For ironing 70 80 0 80 90 100 50 60 Dried without creases Maintenance 1 Turn off the water tap and electricity supply after every wash Open the door to prevent the formation of moisture and odours If the washing machine is left idle for a long period drain any remaining water in the machine and replace the drainage hose Unplug the machine during cleaning and maintenance Use a soft cloth dampened with soapy liquid to clean the machine case and rubber components Do not use corrosive or abrasive chemicals or solvents Clean the detergent compartment regularly Raise the compartment slightly to remove as shown in Figure A and replace after cleaning Clean the filter Cleaning methods once a month 1 Push out the outer cover Fig 1 2 Screw out filter by turning counterclockwise Fig 2 3 Flash clean with running water 4 Replace the filter by turning clockwise and remount the cover Fig 3 Caution The filter must be in place or it may lead to leakage 5 To prevent blockages t
10. lorfast not be used such as Remove all objects from pockets that may cause trichhloroethylene or alike caution damage to the machine such as keys and coins load the appropriate amount of detergent only Clothing with frayed edges or yarns should be put in a wash bag or special bag before washing Repaire damaged clothing lose buttons or damaged zips and hooks before washing Bed sheets and table ware should be loosely loaded and not folded This washing machine is for household use and de signed for mechanically washable clothes When washing separate unwashable clothes with reference to clothes labels 5 Wash Load Laundry Type Non fade cottons Delicat fabrics Woolen fabrics Blending fabrics Washing methods 1 Laundry loading Open the door put in the laundry piece by Load Reference piece and then tightly close the door Jeans 800g cotton appr 950g Notes Pajamas 1 When first using the washing machine 1 a appr 2009 let it run unloaded for one program Shirts appr 300g 2 Do not overload the washing machine 2 Tshirt Underwear cotton appr 3009 appr 70g Socks Overalls Jackets blended fabrics cotton appr _ appr 50g Woolen blankets _ Single bed sheets appr 3000g cotton appr 800g 2 Adding detergent Slide out the detergent drawer and put the required detergent and softener into the corresponding compartments Push back the drawer gently
11. o the water supply or the ingress of contaminants clean the water inlet and inlet water filter regularly 6 If the machine needs to transport to a distant location replace the vibration mounting locks which were removed during installation as shown below a S D gt gt 7 ye Remove the back cover Replace the rubber plugs Insert the bolts Tighten the bolts with a spanner 7 If the washing machine is left idle for a long period turn off the water and electricity supply and open the door slightly to prevent the formation of moisture and odours Trouble shooting The following circumstances do not constitute problems Do not contact the main tenance service until the problem has been confirmed Poor connection to power supply The washing machine fails to Power failure operate Door is not properly closed Machine has not been switched on Water tap is not turned on Water pressure is less than 0 05Mpa The washing machine does The inlet hose is kinked not fill with water Water supply failure The program knob is not properly set The door is not properly closed Check that the height of the water hose is between 80cm and 100cm otherwise the problem will happen when below 80cm Check that the drain hose is not syphoning Drainage hose is bent Drainage hose is blocked Drainage hose end is more than 100cm above the floor level Strong vibration during spin Check that all packing bol
12. olours 40 x O O c O Rinse 5 x x O O O O Soften 6 Softeners x x O x Spin 7 x x x x End dry e Wash program ends and the washing machine stops operation Normal wash A Heavy soiled white laundry 60 x O x D Quick wash B White and fast colours soiled 50 x x O x S O Super Quick C Delicate colours 40 x O x 2 D Rinse D x x O x ari S Soften E Softeners x x O x J Spin F x x x x End dry J Wash program ends and the washing machine stops operation Normal wash I Wollens 40 x O x i x x x o Rinse LI O O g Soften III Softeners x x O x Q Drain IV x x x x Spin y x x x x End Delicate wash program ends and the washing machine stops operation Preparation 1 Power supply 2 Water supply Plug in the power supply Turn on the tap to ensure that the water is clear 220 240V 50Hz Caution Before staring the washing machine turn on the water faucet to ensure that the water faucet and the water inlet hose are connected correctly and do not leak 4 Detergent selection Laundry treament Only special low foam detergent Sort out clothes according to type and extent of dirt should be used in automatic front There are three types of clothes cotton synthetical loading drum washing machine and woolen silk fabrics form blended or wool fabrics Separate white clothes from colored If whites and special detergent should be coloreds are combined for one load make sure used Dry cleaning solvent should the coloreds are co
13. sh electrovalve EVP Prewash electrovalve P1 TH55 55C limiter P2 FD FE Economic wash 12 ON OFF Line Neutral Line LED Door LED MR Thermal Lock Heating motor Heating element Drying element l1 L N S L S0 MV RR RA 0020500531
14. ts have been removed drying The washing machine is located on an uneven surface Operation stops before M P p Water or electricity failure completion of the wash cycle Water heating is taking place Temporary stoppage during Note When the inlet water temperature is less than the ambient wash cycle temperature the washing machine will automatically heat the water to an ambient temperature even if the temperature controller is set to position x m The detergent is not a low foam type Excessive foam in the drum j Excessive detergent has been used Poor connection to the power source Door is not closed properly Program has not been correctly set The dryer knob is not set at the x position The water supply and drainage do not stop Drainage failure Failure of the drying process Check to see if the end of the water drainage hose is submerged in water Incomplete drying The filter is blocked The machine is overloaded Dryer time is set at less than 20 minutes Water tap is not turned on Specifications ETTA 5 oman ED E ing Circui Ir No SPIN PCB 1 B3 B2 B4B8B7 14 Speed button 2nd level pressure cut off switch ist level pressure cut off switch TH36 36 C limiter Delicate drying cycle limiter Strong drying cycle limiter I3 EVL Normal wa
Download Pdf Manuals
Related Search