Haier WQP12-AFM2 User's Manual
Contents
1. its service agent WQP12 AFM2 A ON OFF Light ON OFF Button C Low Salt Indicator Light U D Knob For Selecting Cycle Handle For Opening Door F Eco Button m Installation Positioning the Appliance Position the appliance in the desired location The back should rest against the wall behind it and the sides along the adjacent cabinets or wall The dishwasher is equipped with water supply and drain hoses that can be positioned to the right or the left to facilitate proper installation Levelling the Appliance Once the appliance is positioned adjust the feet screwing them in or out to adjust the dishwasher making it level In any case the appliance should not be inclined more than 2 If the appli ance is level it will help ensure proper performance Cold Water Connection Connect the cold water supply hose to a threaded 3 4 gas con nector and make sure that it is fastened tightly in place see fig 1 A Some models have an Acquablock water supply pipe see fig 1 B with filter in the threaded inlet If the water pipes are new or have not been used for an extended period of time let the water run to make sure that the water is clear and free of impurities If this precaution is not taken there is a risk that the water inlet can get blocked and damage the appliance Hot Water Connection The water supply to the appliance can also be connected to the house s hot water line centralised syste2. and leave the door of the appliance slightly ajar This will help the seals last longer and pre vent odors from forming within the appliance Moving the Appliance If the appliance must be moved try to keep it in the vertical position If absolutely necessary it can be positioned on its back Seals One of the factors that cause odors to form in the dishwasher is food that remains trapped in the seals Periodic cleaning with a sponge will prevent this from occurring Wash Cycle Table O Cycle Selection Description of Detergent Rinse Cycle Button Information Cycle Aid iS Pre wash with hot water Very dirty dishes pots and Extended wash at 65 pans not to be used with deli Rinse with cold water 30g cate items Rinse with hot water Heavy Duty Drying Pre wash with hot water Very dirty dishes pots and Extended wash at 55 pans not to be used with deli Rinse with cold water 30g Heavy Duty cate Items Rinse with hot water Drying 9 Extended wash at 65 Normally dirty dishes pots and Rinse with cold water Normal Wash pans Standard daily cycle Rinse with hot water 30 g Drying tt Extended wash at 55 s Normally dirty dishes pots and AE ji Plater Rinse with hot water 30g pans Standard daily cycle Normal Wash Drying IEC EN 50242 I For dishes that need to be Rinse with cold water K rinsed and dried only Rinse with hot water Drying Rinse R
3. turn the C cap in the anti clockwise direction and then pour in the rinse aid making sure not to overfill The amount of rinse aid used for each cycle can be regulated by turning the F dose adjustor located beneath the C cap with a screwdriver There are 6 different settings the normal dosage setting is 3 Important Proper dosage of the rinse aid improves drying f drops of water remain on the dishes or spotting occurs the dosage adjustor should be turned to a higher setting f the dishes have white streaks turn the dosage adjustor to a lower setting Loading the Dishwasher Before placing the dishes in the dishwasher remove the large food particle to prevent the filter from becoming clogged which results in reduced performance If the pots and pans have baked on food that is extremely hard to remove we recommend that they be allowed to soak before they are washed This will eliminate the need for extra wash cycle Pull out the rack to facilitate loading the dishwasher How to Use the Lower Rack We recommend that you place the items which are the most diffi cult to clean items on the lower rack pots lids serving dishes and bowls as shown in the figure to the right It is preferable to place serving dishes and lids on the sides of the racks in order to avoid blocking the rotation of the top spray arm Pots serving bowls etc must always be placed face down Deep pots should be slanted to allow the wa
4. use too much detergent the result will not be cleaner dishes but rather a greater nega tive impact on the environment It is important to try and run the dishwasher when it is fully loaded to save on energy In order to prevent odors from form ing and food from caking onto the dishes you can run the hold cycle There is no utility in rinsing dishes cookware and untensils Choose the right wash cycle the choice of cycle depends on the type of dishware cookware and utensils being washed and how dirty they are before placing them in the dishwasher How to Keep Your Dishwasher in Shape After Every Wash After every wash turn off the water supply to the appliance and leave the door slightly ajar so that moisture and odors are not trapped inside Remove the Plug Before cleaning or performing maintenance always remove the plug from the socket Do not run risks No Solvents or Abrasive Cleaning Products To clean the exterior and rubber parts of the dishwasher do not use solvents or abrasive cleaning products Rather use only a cloth and warm soap water To remove spots or stains from the surface of the interior use a cloth dampened with water and a little white vinegar or a clean ing products made specifically for dishwasher When You Go on Holiday When you go on holiday it is recommended that you run a wash cycle with the dishwasher empty and then remove the plug from the socket turn off the water supply
5. Economic fast cycle to be used Short wash at 55C ee to on not very dirty dishes right Cold rinse i g Rapid Wash after they are used No drying cycle LALAN rit li Soak Pre wash of dishes pots and pans while waiting for the load to be completed after the subse quent meal Short cold wash to prevent food resi due from drying on the dishes Detergent and Rinse Aid Detergent Detergent specifically intended for use with dishwashers must be used The dispenser must be refilled before the start of each wash cycle following the instructions provided in the Wash Cycle Table The detergent dispenser is located on the inside panel of the door Loading the detergent To open the A cover on the dispenser press the B button The detergent for the wash cycle should be poured into the C compartment After the detergent has been placed in the dispenser close the cover and press down until it clicks in place Notice To facilitate closing the cover remove any excess detergent on the edges of the dispenser Rinse Aid This product makes dishes sparkle and helps them to dry with out spotting The dispenser is located on the inside panel of the door and should be filled after every 80 wash cycles Loading the Rinse Aid Regardless of the type detergent dispenser installed on your appliance you must proceed as indicator below when loading the rinse aid To open the dispenser
6. Installation Diagram wiring box ut power switch 30e 1 2 rejector s gPower indicator door switch Is A o 1 7 water level switch salt mis VAF 3 se spy lamp temperature controller drain g pum l 3 PSP ar G k 1a ECO washing softener DENN dispenser Yev 1inlet valve fd washing so eve X pump J softener timer alge pump 32 J TAQs 1 overflow switch temperature limiter heater temperature limiter Haier Domestic Dishwasher WQP12 AFM2 Haier Code 0120501715 Safety Is a Good Habit to Get Into NOTICE Carefully read the instructions contained in this manual as they provide important information which is essential to safe and proper installation use and maintenance of the appliance C This appliance complies with the following EEC directives 73 23 EEC of 19 02 73 Low Voltage and subsequent modifications 89 336 EEC of 03 05 89 Electromagnetic Compatibility and subsequent modifications Carefully dispose of the packing material After removing the packing check to make sure that the appli ance Is not damaged If in doubt contact a qualified professional The dishwasher must only be used by adults for the washing of household dishes and cooking utensils Fundamental rules to follow when using the appliance Never touch the dishwasher when bare foot or with wet hands or feet We discourage the use of extensi
7. button and the ON OFF light will turn on At this point the wash cycle will begin Important In general it is not advisable to open the door while the machine is working Care must be taken if the door is opened during the hot phase or immediately after a programm has finished as steam may escape Cancelling or modifying a wash cycle setting Press the ON OFF button and the ON Light will turn off Rotate the knob in the clockwise direction to the desired cycle setting see the section entitled Starting a wash cycle Then turn the dishwasher back on using the ON OFF button Wash Cycle adjustment Buttons C Button This button see close up View Control Panel letter F is used for normal dirty dishes pots and pans It is standard daily cycle At the end of the wash cycle When the knob stops turning and is aligned with a STOP mark see figure the cycle has finished Turn off the appliance using the ON OFF button turn off the water supply and open the door of the dishwasher Wait a few minutes before unloading the dishwasher to avoid handling the dishes and utensils while they are still hot and more susceptible to breakage They will also dry better
8. m heating system as long as it does not exceed a temperature of 60 C In this case the wash cycle time will be shortened by about 15 minutes and the wash efficiency slightly reduced The connection must be made to the hot water line following the same procedures as those for the connection to the cold water line 10 Drain Hose Connection Insert the drain hose into a drain pipe with a minimum diameter of 4cm or let it run into the sink making sure to avoid bending or crimping it Use the special plastic support that comes with the appliance see fig C The free end of the hose must be at a height between 40 and 100 cm and must not be immersed in water MAX 100 MIN 40 fig C Attention The special plastic hose support must be solidly fastened to the wall to prevent the drain hose trom moving and allowing water to soll outside the drain Electrical Connection After making sure that the voltage and frequency values for the current in the home correspond to those on the rating plate located on the stainless steel inner door of the appliance and that the electrical system is sized for the maximum voltage on the rating plate insert the plug into an electrical socket which is earthed properly the earthing of the appliance is a safety requirement mandated by law If the electrical socket to which the appliance must be connected is not appropriate for the plug replace the plug rather than using adaptors or
9. ollows Remove the lower rack and then unscrew and remove the cap from the salt container If you are filling the container for the first time fill it with water Place the end of the funnel Supplied into the hole and intro duce about 2 kg of salt It is normal for a small amount of water to come out of the container Carefully screw the cap back on The salt container should be filled after about every 30 wash cycles To prevent the formation of rust load the salt just before begin ning a wash cycle Adjusting Salt Consumption The dishwasher is equipped with a system to adjust the level of salt consumption in function of the hardness of the water being used in order to optimize and customize the level of salt con sumption while keeping it to a minimum To adjust salt consumption level follow these instructions Unscrew the cap on the salt container On the container there is an arrow see figure to the side If necessary turn the arrow in the anti clockwise direction from the setting to the setting based on the hardness of the water being used It is highly recommended that the table be consulted when making adjustments Water Hardness Salt mmol l pee ol consumption ere position Grams cycle cycles 2kg oro osz 18 44 1 8 4 4 45 89 4 5 8 9 9 Clarke degrees dH 0 10 gt 89 gt 8 Energy Saving Tips Use the right amount of detergent if you
10. on cords and multiple sockets During installation the power supply cord must not be exces sively or dangerously bent or flattened Close up View Control Panel If the appliance is not operating properly or maintenance must be performed disconnect the appliance from the power supply Keep detergents out of the reach of children who must also be kept away from the dishwasher when it is open This appliance cannot be installed outdoors not even if the area in which it is installed is covered by a roof it is also very dangerous to leave it exposed to the rain and elements Do not touch the heating element during or after a wash cycle Do not lean or sit on the door when it is open as this could overturn the dishwasher If the appliance malfunctions turn off water supply to the appli ance and disconnect the plug from the wall socket Then con sult the section entitled Troubleshooting If you can not solve the problem contact a service centre Only specialised personnel are authorised to make repairs Appliances which are no longer being used must be made inoperable by cutting the power supply cord and removing the door lock The appliance must be positioned so that the plug is accessible The carpet must not obstruct the opening when the appliance in Stalling on the ground with carpet If the supply cord is damaged it must be replaced by a special cord or assembly available from the manufacturer or
11. ter to flow out The silverware basket can be doubled see fig A so that only one section may be used when the silverware load is light This also makes space for additional pots and pans on the lower rack Silverware should be placed in the silverware basket with the handles at the bottom if the rack has side baskets the spoons should be located individually into the appropriate slots Espe cially long utensils should be placed in the horizontal position at the front of the upper rack How to Use the Upper Rack The upper rack is designed to hold more delicate and lighter dishware such as glasses coffee and tea cups and saucers as well as plates small bowls and shallow pans as long as they are not too dirty Position the dishes and cookware so that they do not get moved by the spray of water The upper rack can be adjusted for height See fig B Lower Rack Upper Rack Starting the Appliance Starting a wash cycle Make sure that the plug for the appliance is inserted into the wall socket Make sure that the water supply is turned on to full pressure Load the dishwasher see the section entitled Loading the Dishwasher Pour in the detergent see the section entitled Salt Detergent and Rinse Aid Turn the knob located on the right of the control panel in the clockwise direction until the number or symbol for the cycle sec tion entitled Wash Cycle Table Press the ON OFF
12. the like as they could cause overheating and burns Cleaning and Special Maintenance Filter Assembly For the best performance and results the filter assembly must be cleaned The filter efficiently removes food particles from the wash water allowing it to be recirculated during the cycle For this reason it is a good idea to remove the larger food particles trapped in the filter after each wash cycle by rinsing the A semi circular filter and cup under running water To remove the filter assembly pull on the cup handle in the upward direction The entire filter as sembly made up of the A semicircular filter and the B fine filter should be cleaned at least once a month To clean the filter and the fine filter use a cleaning brush Then reassemble the filter parts as shown in the figures below and reinsert the entire assembly in the dishwasher positioning in its seat and pressing downward The dishwasher must never be used without the filters Improper replacement of the filters may reduce level of the appliance and damage dishes and utensils Troubleshooting It may occur that the dishwasher does not function or does not function properly Before calling for assistance let us see what can be done first have you forgotten to press one of the buttons or to perform an essential operation The Dishwasher Does Not Start Have you checked whether the plug is pushed into the socket correctly the power is on in the ho
13. the salt container is closed properly the rinse aid dosage is correct If despite all these checks the dishwasher still does not function and or the problem persists contact the nearest authorised ser vice centre and provide them with the following information the nature of the problem the model type number Mod And the serial number S N which are indicated on the plate located on the side of the inner part of the door Never call on unauthorised technicians and refuse to allow parts to be installed that are not original spare parts Close up View Interior A Upper Rack B Rack Height Adjustor C Top Spray Arm D Lower Rack Technical characteristics Width Depth Height Capacity Mains water pressure Power voltage Total absorber power imo OU gt Bottom Spray Arm Washing Filter Detergent and Rinse Aid Dispenser IO Tn m Salt Container Cap 60 cm 60 cm 85 cm 12 standard place settings 0 03 0 6 MPa 220V 50Hz 1950W S a t ceccee Salt The hardness of the water varies from place to place If hard water is used in the dishwasher deposits will form on the dishes utensils The appliance is equipped with a special softener that uses a salt specifically designed to eliminate lime and minerals from the water Loading the Salt into the Softener Always use Salt intended for use with dishwashers The salt container is located beneath the lower rack and should be filled as f
14. use the door is closed properly the ON OFF switch is on ON the water supply is turned on The Dishwasher Does Not Load Water Have you checked whether the water is turned on and the hose is connected properly the water supply to the house on and has sufficient pressure the water supply hose is crimped or bent the filter for the water supply hose is clogged The Dishes Are Not Clean Have you checked whether the water is turned on and the hose is connected properly Cleaning the Spray Arms It may happen that food particle become encrusted on the sprayer arms and block the hole Check the sprayer arms periodically and clean them when needed See Close up view interior letters C E Cleaning the Water Inlet Filter Periodically clean the water inlet filter see figure 1 A located on the outlet of the water supply tap After turning off the water tap unscrew the end of the water sup ply hose remove the filter and clean it carefully under running water Then return the filter to its place and tighten the water supply hose back into position the water supply to the house on and has sufficient pressure the water supply hose is crimped or bent the filter for the water supply hose is clogged The Dishwasher Does Not Drain Have you checked whether the drain hose is crimped or bent Lime Deposits or a White Film Form on the Dishes Have you checked whether the lid to
Download Pdf Manuals
Related Search