Haier HWM60-10 User's Manual
Contents
1. Is there power failure Use it when the power is on Not wash Is the power plug loose Insert the power plug tightly The machine Does the water level arrive at the Affusion to the set water level does not act set water level Not spi Is the power plug loose Insert the power plug tightly OF SP Is thetop lid closed Close the top lid Are the laundries put orderly Put the laundries orderly There s abnormal sound Is the machine slanting Level the machine properly inside the machine Are the laundries slanting in Re order the laundries spinning The water faucet leaks Is the jointer screw of the water Fasten the jointer screw inlet hose is loose or twisted properly awry Common phenomena The spinning is intermittent when it starts Balance the laundries to avoid slanting e Push the Procedure selection button to e The program is setting the drain time Some time is select Spin but it doesn t work needed before it starts spinning There may be some water flowing out of It is the water remained in the factory inspection of the drain hose in the first use of the machine performance While water filling in wash and rinse the To prevent splash during water filling pulsator pauses rotation e Supplementary water filling 48 s after sensor tests cloth material Wash pauses e tne It is the special resume function In the case of power2. a Confirm if Clear the pocket Fasten the there s special Take out the buttons and requirement for coins sand zippers the laundries hairpins etc F Q ZO The quantity of the laundries shall not exceed the rated value The big laundries like the jeans shall be put in loosely Y When the pulsator is running the buttons of the laundries may cause noise For the sake of discretion please put the laundries with buttons into other laundries RS iS A Please check if the laundries are applicable for washing b Separate those not colorfast from other laundries C For laundries not water absorbing please put them into water with hands D For laundries with much soil please remove the soil first You can add detergent on the part with serious soil directly It is much easier to remove the soil by that mean E For laundries likely to get lint ball or with long fiber please first turn the inside out before putting them into the water f Do not put the laundries polluted with chemicals directly into the washing machine g For those small laundries laundries likely to be twisted or worn and woolen laundries please put them into mesh bag before washing Put in the laundries e The capacity of washing and spinning of the machine refer to the largest weight of the standard laundries under dry condition that can be washed or spinned in one time One time w
3. Figure 4 x Claws at the lt two sides z Rats ae Lower bread x Figure 2 7 Screw Nip the drain hose outlet Figure 4 and take off the drain hose hook Usage of the drain hose The drain hoseshall drain smoothly N 1 The height of the drain hose shall be 4 If extra drain hose is needed please less than 10cm or the drainage will not make separate purchase The inner be smooth and cost such long time that diameter of the extra hose shall not the machine may stop at mid way less than 30mm and the length shall 2 Do not trample or press the drain hose not exceed 1 5m 2 _30mm at mid If the extrahose is toolong cut it point To make smooth drainage cut the either atA orat B point front end of the hose slantingly G Co 2Q EZ Install the water inlet hose Confirm the water tap a Water tap suitable Water tap not suitable Outlet end surface It is requiredthat the frontend shall belonger than 10mm The outlet end surface of thetap shall be flat and smooth If not please file it to Seay leakage J Connection between the water inlet hose jointer and the water tap 1 Use the new water inlet hose provided with the machine to connect to the water b faucet Old hose sets should not be reused 2 Press the lower end of the lock lever and push down the slider Take off the water inlet hose jointer from the water inlet hose component See to Figure 1 3 Loosen t
4. When the power plug is inserted computer _ failure or the power plug is loose during washing the board indicator is switched on and the machine machine can save the running program and resume starts working the program after the power supply is recovered You do not need to set the program again Packing list a Name S Quantity e User s manual One piece Guarantee e One piece e Components ofthe water _o inlet hose One piece e Lint filter e One piece Bottom plate One piece Tapping screws Fr Five pieces d g Fulyl automatic washing machine e One set E
5. shall not use the machine Please keep the lint filter in good condition and install it to proper position If the lint filter is lost or damaged please contact the local after sales service department of our company Put down N Keep the machine away from direct sunlight and heat source like the heater To protect your laundries and wash ing machine please take out all of the coins buttons sand hairpin and other foreign materials before washing Q AO Please check if the water faucet is open and if the connection of the water inlet pipe is proper It is suggested to use foamless washing powder Installation and adjustment Please install and adjust the machine according to the requirement of the manual It is very important to your security and correct operating the machine Install the lint filter Install the bottom plate f After you open the package please lean the 1 Press downward to washing machine gently down on soft items assmble like the towel cloth blanket etc Install the 2 Pull upward to detach bottom plate to the bottom of the machine with the five screws by a cross screwdriver then pe ift the machine up gently See to the figure Back Pull down Putin Front Soft items Bottom plate Screw Adjust the installation position The largest allowed slope of the shank base of the machine is 2 The slanting or rough g
6. the washing machine will perform full automatically controlled fuzzy programto set waterlevel water flowand wash durationaccording to the cloth nature and weight f there is water inside the tub the machine cannot detect the laundries and will display middle level If wet laundries are put in it may display high level You must set suitable water level by yourself Xe e Even there s nowater in thetub the spinning will start after acertain period Do not usesoak process forwoolen laundries e Wash the laundries that are prone to lose colors separately from other laundries The pulsator will not rotate unless the water is filled to selected water level Selection method of the procedure programs Times of pushing the select button Selected program Applicable procedure Contents tthe nixie tube indicates the programs about to run 0 STANDARD Normal wash Wash bb Rinse cc Spin dd Large thick or heavily soiled Soak AA Wash bb i JEANS ia n ry Rinse CC Spin dd The laundry needn tspin to F x 2 GENTLE avoid wrinkles Wash bb Rinse cc Spin dd 3 QUICK WASH For load below 1 kg Wash bb Rinse cc Spin dd 4 WASH Repeat using thewashing Wash bb liquid When the laundries need only 5 SPIN spinning after manu Spin dd a washing first drainthen spin If you pushthe PROCEDURE SELECTION button for 6 times it willresume the original mode and
7. Inner tub Control panel film Pulsator Cabinet Base frame Names of the parts Top lidA Water valve Power line Back cover fixed foot 3 Adjustable foot Meaning and description of the symbols Warning sign Contents marked with that symbol are related to the eye of the product and the personal safety of the users Please operate in strict conformity to the contents otherwise it may cause damage of the machine or injure the personal safety of the user Forbidden sign Contents marked with that symbol are actions forbidden to perform Performing of those actions may result in damage of the machine or injure the personal safety of the user wes Safety precautions a Please plug the plug on special receptacle with rated voltage Be sure to use single phase three pins receptacle Ensure the earthing prong of the power receptacle is earthed reliably Use leakage protector if possible The power cord plug should be convenient to be pluged in or pluged out with hand while the washing machine runs normally Be sure to pull the plug out and close the water tap when the machine is idle when moving the machine or when cleaning the machine Do not use wet hand to insert or pull out the power plug wipe with dry cloth carefully a Do not damage the power cord bend extend twist bind or alter it by force Do not press or nip it with weight If th
8. User s manual Fully Automatic Washing Machine This manual is for HWM60 10 e Please read this manual carefully before using Retain it for future reference Contents Specifcations E AT abl scart eae ielen nem cad the 2na cover NAMES Gr NE DANS ansiiond visu ionind mavaleduneiriisiaiidemnienkanaeaiy 1 Safety precaution srini ia t a tem A a tea 2 Installation and adjustment sssssssesirssssssserrrrrsssssrrrrrrssssnnrrrrrssssnnrernrssssnnnrnrnnss 4 Preparation before washing ssssssseeiirsssssserrrrrssssssrrrrrsssssnrrrrrrssnnrrrrrrsssrnrens 8 Put in the laundries sssssssssseesieiseerssssssssssssseetetttntrrrrrrinnnnnnnnnnnnnnnttetnnnnnnnnnnnaa nt 9 Usage of the detergent sssssisiriesssssiiernrssssirininirseisininrisennnererniannaoonrnnissasornnia 9 Use the operation buttons sissssesessssesssssstettttrrirrrrrrssrsnnnnnnnnnnnntternrrrnrnnnnas 10 Close the toid sieunan nn a a N 13 FASK ASIII ienei cnnan a aea ioi 13 Disposal after washing sssssseeeeessssssserirrrssssserrrrrsssssnerrrrrssssnnrrrrrssssnnrrrrrsssnnres 14 Trouble shooting Answer tO QUESTION 15 Packing list Arae athe telat R 16 ke Specification Water level Water High About 48 L Medium About 37L quantity about Low About 30L Very low About 20L Water inlet pressure 0 03MPa 1MPa Rated washing spinning caraai 6 0kg 6 0kg Control panel Filter cover
9. ashing quantity shall be lower than the rated capacity The thickness size type of the cloth will inf luence the actual washing capacity It is sui table for one time washing to put in reasona ble amount of laundries and the laundries can be turned round in washing Do not select High water level for laundries small than 1 0kg so as toavoid splashing of water Towash thin laundries like the stocking silk etc please first put them into washing mesh bag which can be purchased separately before wash Usage of the detergent How touse the washing powder Direct dissolved in the machine 1 Fill waterto Low water level 2 Add the power Run for 30 seconds to dissolve it completely 3 Put in thelaundries Select suitable water level Howto sethewhit ner Le aa aca of the washing 1 Prepare warm water of 30 Cand a Fill water todecided level Dilute container the whitener with container Pour 2 Add the powderwhile stirring to it slowly into the washing tub fully dissolve it e Avoid using whitener on Put inthe proper quantities detergent laundries with color or pattern as according to the water level and the they are prone to lose color laundries quantities The whitener shall not touch the It is suggested not to use high laundries directly sudsing detergent Inlet box of the detergent Refer to the user s manual for Washing powderwith poor quality or the usage and quantity of the long
10. cle ends Disposal after washing After using please clean the lint and foreign materials of the lint filter etc in time Otherwise it may influence your using the machine Please first pull off the power plug from the receptacle before cleaning e When washing lint filter must be used e After using please clean it in time Lint filter 1 Pull upward to detach Clean Figure 1 2 Clean the lint Put it in water and clean while it is still wet LA See to Figure 1 3 Press downward to assemble Put up Figure 2 The filter screen of the water inlet If the cabinetis dirty wipe itwith wet cloth valve is likely to be blocked by e Do not flush it directly with water foreign materials andinfluence the water inlet Please clean it e Wipe it with neutral detergent Do not wipe it with thinner petrol alcohol etc 1 After washing close the water faucet If needed you can dismantle the water inlet hose 2 Do not store water in the washing machine for a long period Drain the water completely after each using 3 Be sure to pull off the power plug before maintenance 4 Hang up the power cord and drain hose 5 Wipe off the water drops on the surface of the machine and inside the tub Open the top lid for some time about 1 hour then close the top lid Trouble shooting Answer to question If there s breakdown please pull off the power plug before checking The following phenomena are not breakdown
11. e power cord or the power plug is bad or the power plug becomes flexible to avoid risk it is required to have it replaced by the technicians of our special shop or the after sale service department Keep the pin of the power plug clean if the power plug is polluted with dust please o Do not put the machine at damp place like the bathroom Never wash it with water Not put wet laundries on the control panel Do not use water hotter above 50 C In case the washing machine is installed on ground with carpet do not block the ventilation hole with carpet The ventilation holes at the bottom soft items 9 Do not wash water proof laundries like the raincoat bike covers etc to avoid abnormal vibrations in spinning the plugging into the receptacle is loose do not use the plug any more Do not let the machine share one receptacle with other electric appliances If the power plug is damaged or 9 Do not stretch hands into the working machine It is dangerous even if the rotation is slow Take special care of the children Do not let the children climb the washing machine Safety precautions Do not decompose repair or alter the machine by yourself Do not put any hot or heavy items such as the kettle with hot water on the washing machine Do not wash laundries with volatile materials such as thinner petrol etc The handicapped or children without care
12. h cycle end The indicator flashes to indicate in reservation Remarks 1 After pressing POWER ON OFF to connect power supply if the washing machine lasts idle more than 5 min it would automatically shut off the supply Use the operation buttons b Operating procedure and explanations for the buttons PROGRAM STATUS PROCEDURE STATUS E FUZZY Ono REMAINING MINUTES 1 __ _STANDARD FA SOAK Oww z JEANS bh WASH Ow 2 B GENTLE ita RINSE O VERY Low 2 a QUICK WASH dd SPIN WASH SPIN START PROGRAM y a PAUSE WATER LEVEL Z DELAY TIME j L 1 Press the POWER ON OFF button to switch on the power supply e It has the special power resume function In the case of power failure or the power plug is loose during washing the machine can save cD ON OFF the running program and resume the program after the power supply is recovered You do not need to set the program again 2 Press the button of PROGRAM DELAY TIME to select a suitable full automatic program 1 PROGRAM DELAY TIME After switching on the Standard program will be the default If other full automatic program is desired youcan press the button PROGRAM DELAY TIME to getthe corresponding indicator on Refer to the Button of PROGRAM DELAY TIME paragraph on page 10 Page 10 ae Example Use the Quick program for slightly soiled articles When standard programis selected
13. he screw till the water tap can be accessed Put the jointer of the water inlet hose on the tap See to Figure 2 If the tap diameter is too large and the jointer can not be set on the water tap please loosen the four screws and take out the bushing in the jointer See to the figure3 Water inlet pipe jointer Slider Screwdriver SA VS 1 bushing _ Water inlet pipe Figure 1 4 Fasten the four screws evenly See to Figure 4 5 Take off the nameplate Twist the fastening nut as per the indication of the figure See to Figure 5 Remarks Before twisting the fastening nut the thread is4mm above the upper surface ofthe nut After twisting the fastening nut thethread is 2mm above the uppersurface of thenut See toFigure 6 Figure 2 Figure 3 About 4mm before twisting About below 2mm after twisting Figure 6 yy Connection between the water inlet hose and the washing machine 1 Do not takeoff the water absorption Nut of the water inlet hose cushion Please checkif the cushion a Ss is dropped ordamaged before each usage If ithappens please contact Y our after sale departmentimmediately S gt 2 Put the nutof the waterinlet hose on Z the valve jointer 3 Fasten the nut Swaying it gentlyto Water absorption cushion confirm if it s suitable Jointer of the water inlet valve Connection between the jointer of the water inlet hose and the water inlet hose 1 Push down theslider I
14. it will circulate like that If you selectthe QUICK WASH program you haveto set the full procedure of wash rinse andspin The procedure can notbe selected 3 Press the WATER LEVEL button to select suitable water level WATER LEVEL After switching on the power press the button WATER LEVEL to selecta water level according to the load Please refer to the button Water level on page 10 4 Push the PROGRAM DELAY TIME button S to select suitable reserve program e PROGRAM DELAY TIME After switching on the washing machinereserved wash programwill be automatically set inactive If youdesire a washcycle to endat a reservedtime you canpress the PROGRAM DELAY TIME button over 2seconds to seta delay time wash program Refer to The button of PROGRAM DELAY TIME on page 10 HEED El e When Delay time becomes active thenixie tube displays the time to the endof the delaytime wash cycle and the indicator turnson During delay time procedure push the a Delay time button to display the delay time mode Tochange the running program or cancelthe delay time you should cutoff the supplyand reselect HEL START PAUSE 5 Press the start pause button v4 Close the top lid Except water filling washing rinsing and draining if the top cover is opened the washing machine will stop running and alarm Finish washing The washing machinecuts off the power supply automatically when washcy
15. nsertthe LD water inlet hoseinto the jointer Jointer of the water 2 Hang the locklever to the jointer inlet hose Release the slidertill a click Locking lever 7 2 slider sound is heard Check the connection between the jointer of the water inlet hose and the water tap 1 Swaying the hose gently to confirmif it isfastened stable 2 After installation openthe tap tocheck if itleaks 3 Do not bendthe hose withoverstrain 4 Before each usage please check if the connection between the jointer of the waterinlet hose andthe water tap and theinstallation of the water inlet hoseare firm soas to prevent dropping fromimproper Installation position Takedown the water inlet hose 1 Close the watertap 2 Press the lockinglever Pushdown the slider Then pull off the water inlethose If the machine is used more than onceevery week thejointer of the water inlet hose canbe kept onthe tap toprevent damaging the fixing screw Preparation before washing Preparation before washing 1 Connect the water inlet hose and open the water tap 2 Confirm that the washing machine is earthed reliably Then insert the power plug into the receptacle Do not connect the earth ter minal to the gas pipe and tap water pipe 3 Put down the drain hose 4 Slanting or uneven ground may result in unstable working or abnormal noise Please aome the machine stand horizontally Pay attention to followings before washing the laundries
16. round will result in unstable running or stoppage of the machine Please adjust it with following methods Adjust the adjustable foot 1 To twist the adjustable foot please first lift up the side of the foot slightly loosen the adjustable nut and twist the foot 2 Fasten the nut after adjustment A How to change the direction of the drain hose 1 Loosen the fastening screw of the 3 Extend the drain hose from the installation back cover to take off the back cover hole at the right side of the base frame Fix Be careful not to do it by force to the drain hose onto the base frame with the prevent breaking the claw of the back drain hose frame and fasten the screw Then cover as indicated in Figure 1 set the drain hose hook on the drain hose and hang the drain hose on the hanging hole of the cabinet As indicated in Figure 3 ae Figure 1 2 Take off the drain hose from the cabinet N Figure 3 Nip the drain hose outlet slightly 4 To install the back cover first hang the lower Dismantle the drain hosehook Loosen beard of the back cover on the cabinet then the fixing screw of the drain hose frame push the claws at the two side and the upper to dismantle the drain hose frame Pull end from bottom to top to resume the original the drain hose into the cabinet from the setting Be careful not to do left side of the base frame it by force Then fasten Drain nose fame the screw two points as indicated in
17. s sometimes Please confirm again before sending it to repair If there are real breakdowns please come to the special maintenance department or after sale service department of our company Do not repair it by yourself Buzzing upon reservation starts The top lidis not closed Close the top lid Nixie tube indicates E0 Put down the drain hose Open and close the top lid once Clean the foreign material Open and close the top lid once No or slow drain nixie tube Is the drain hose put down indicates E1 buzzing Is the drain hose blocked by foreign material nixie tube indicates Eg The top cover leaves open Close the top lid buzzing Safety switch actuates not spin Are the laundries put Re order the laundries Close the after self correction twice slantingly top lid Level the machine in right nixie tube displays E3 buzzin i ina position P 9 Is the machine slanting Open and close the top lid once No or slowwater filling The water tap is not open Open the water tap Push the nixie tube indicates E4 The water inlet valve is blocked Start Pause button buzzing e Clean the water inlet valve The water pressurels too push the Start Pause button low and thecurrent is Wait for the normal water pre too small ssure before use Poor or no waterfall flow f the nozzle is choked with Remove the foreign bodies foreign bodies
18. time storage maybe caked whitener Please pay attention tocleaning the For powder whitener please detergent box intime dissolve it before use Use the operation buttons a Description of the function of the buttons To indicate during sensing Press Power On Off button to connect To indicate remaining min During power supply program running After power isconnected pressing this To indicate remaining reserved button will cutoff the s ppiy time hrs during delay time period To indicate fault symbols for abnormal conditions see page 15 After the poweris switched on press it to start the machine During working pushit to pause working During pause pushthis button torestart and continue operation BE eee Beene ae i E E PROGRAM STATUS PROCEDURE STATUS 7 SS Beueze Onion REMAIN ING MINUTES i STANDARD ar SOAK O miw z JEANS bb WASH Oto M GENTLE m RINSE Overy ton m QUICK WASH s SPIN os WASH w SPIN ZS PROGRAM WATER LEVEL 7 DELAY TIME LJ 7 7 a 7 The user selects a suitable water level Press PROGRAM DELAY TIME button depending on the load you can select one or several programs of Standard Jeans Gentle Quick Wash Wash and Spin Press PROGRAM DELAY TIME button over 2 seconds you can select the program of reservation The nixie tube displays the delay hours to the was
Download Pdf Manuals
Related Search