Haier HSU-07RK03/R2 User's Manual
Contents
1. 21 Maintenance For Smart Use of The Air Conditioner A WARNING Before maintenance be sure to turn off the system and the circuit breaker Remote Controller Indoor Body Wipe the air conditioner by using a soft and dry cloth For serious stains use a neutral Do not use water wipe the controller with a detergent diluted with water Wring the water dry cloth Do not use glass cleaner or chemical out of the cloth before wiping then wipe off cloth the detergent completely Do not use the following for cleaning m Ce Gasoline benzine thinner or cleanser may Hot water over 40 C 104 F may cause damage the coating of the unit discoloring or deformation Air Filter Cleaning 1 Open the inlet grille by pulling it upward 2 Remove the filter Push up the filter s center tab slightly until itis released from the stopper and remove the filter downward 3 Clean the filter Use a vacuum cleaner to remove dust or wash the filter with water After washing dry the filter completely in the shade 4 Attach the filter Attach the filter correctly so that the FRONT indication is facing to the front Make sure that the filter is completely fixed behind the stopper If the right and left filters are not attached correctly that may cause defects 5 Close the inlet grille 22 Maintenance Replacement2. Connect power supply cord to the outlet completely STRICT ENFORCEMENT Do not use power supply cord in a bundle PROHIBITION Do not start or stop the operation by disconnecting the power supply cord and so on PROHIBITION STRICT ENFORCEMENT QD STRICT ENFORCEMENT Take care not to damage the power supply cord Mz ES PROHIBITION Do not channel the air flow directly at people especially at infants or the aged on A CAUTION Do not use power supply cord extended or connected in halfway OQ PROHIBITION Do not insert objects into the air inlet or outlet c PROHIBITION Do not try to repair or reconstruct by yourself Do not use for the purpose of storage of food art work precise equipment breeding or cultivation GL O Hear PROHIBITION Do not install the unit near a fireplace or other heating apparatus a c 9 PROHIBITION Do not place animals or plants in the direct path of the air flow w O PROHIBITION Take fresh air occasionally especially when gas appliance is running at the same time STRICT ENFORCEMENT Check good condition of the installation stand O PROHIBITION Do not place any objects on or climb on the unit PROHIBITION Do not operate the switch with wet hand PROHIBITION Do not pour water onto the unit for cleaning Do not place flower vase or water contain
3. SLEEP SLEEP operation starts operation stops C In HEAT mode 3 In AUTO mode The unit operates in corresponding sleep mode adapted to the automatically selected operation mode 4 In FAN mode It has no SLEEP function TESS Note The sleeping hours lasts 8 hours and couldn t be adjusted When timing on function is set the sleeping function can t be set up After the sleeping function is set up if user resets timing on function the sleeping function will be cancelled the machine will be in the state of timing on If the sleeping function and timing on function are set up at the same time no matter which one is operated earlier the machine will be off automatically and the other function will also be cancelled 15 Operation Timer On Off Operation Set clock correctly before starting TIMER operation Remote Controller 1 After unit starts select your desired operation mode Operation mode will be displayed on LCD 2 Timer mode selection Press TIMER button to change TIMER mode Every time the button is pressed display changes as follows Remote controller EI zi DM m5 ANK 200 200 tap TIMER ON TIMER OFF TIMER ON OFF Then select your desired TIMER mode TIMER ON or a TIMER OFF pr or 93 will flash ane X 3 Time setting Press HOUR JA V button A Every time the button is pressed time setting increases 1min if kept depressed it will increase rapidly
4. Every time the button is pressed time setting decreases 1min if kept depressed it will decrease rapidlly It can be adjusted within 24 hours 4 Confirming your setting After setting correct time press SET button to confirm ENS or on the remote controller stops flashing Time displayed Unit starts or stops at x hour x min TIMER ON or TIMER OFF 5 Cancel TIMER mode Just press TIMER button several times until TIMER mode disappears Hints After replacing batteries or a power failure happens time setting should be reset Remote controller possesses memory function when use TIMER mode next time just press SET button after mode selecting if time setting is the same as previous one 16 Operation Timer On Off Operation Remote Controller mI L lc COD egg TEMP SO MODE HEATHARFLOW SLEEP HEALTH Set clock correctly before starting TIMER operation 1 After unit starts select your desired operation mode 2 Timer mode selection Press TIMER button to change TIMER mode Every time the button is pressed display changes as follows Remote controller gt EMI BLANK eno ieni le p TIMER ON TIMER OFF TIMER ON OFF Then select your desired TIMER mode TIMER ON OFF will flash 3 Time setting Press HOUR A V button Z Every time the button is pressed time setting increases 1min if kept depressed it will increase rapidly V Every time the
5. Hints When making coolness wind orientation should adjust to the horizontal state in favor of air circulating in the room for cool air will agglomerate upside When making heat wind orientation should adjust to the slanting down state in favor of air circulating in the room for hot air will agglomerate downside Operation Sleep Operation Before going to bed you can simply press the a SLEEP button and unit will operate in SLEEP mode and bring youa sound sleep SLEEP operation starts SLEEP operation stops Use of SLEEP function henna After the unit starts set the operation status then press SLEEP button before which the clock must be adjusted and time being set Operation Mode 1 In COOL DRY mode 1 hours after SLEEP mode starts temp will become 1 C higher than temp setting After Temp setting Unit stop another 1 hours temp rises by 1 C further M In COOL DRY mode The unit will run for further 6 hours then stops te hi 2 In HEAT mode Temp is higher than temp setting so that room temperature won t be too low for your sleep Mire eoi El e fen ea setting After another 1 hours temp decrease by 2 C further After more Remote Controller another 3 hours temp rises by 1 C further The unit will run for further 3 hours then stops Temp is lower than temp setting so that room temperature won t be too high for your sleep Temp setting Unit stop 3hrs Rises 1 C
6. button is pressed time setting decreases 1min if kept depressed it will decrease rapidlly It can be adjusted within 24 hours 4 Time confirming for TIMER ON After setting correct time press TIMER button to confirm BIN on the remote controller stops flashing pa starts flashing Time displayed Unit starts or stops at x hour x min 5 Time setting for TIMER OFF Just press HOUR button follow the same procedure in Time setting for TIMER ON 6 Time confirming for TIMER OFF After time setting press SET button to confirm on the remote controller stops blinking Time displayed Unit stops at X hour X min To cancel TIMER mode Just press TIMER button several times until TIMER mode disappears According to the Time setting sequence of TIMER ON or TIMER OFF either Start Stop or Stop Start can be achieved 17 Operation Power Soft Operation EDET alli L Ic AMI SOZ MODE HEATHARROW SLEEP POWER Operation When you need rapid heating or cooling you can use this function Selecting of POWER operation Press POWER SOFT button Every time the button is pressed display changes as follows 7 BLANK POWER SOFT Stop the display at 7 In POWER operation status In HEAT or COOL mode fan speed automatically runs in HI mode for 15 min then returns to original status setting To cancel POWER operation Press POWER SOFT button twice POWER SOFT disapp
7. in the air and also to kill bacteria and speed up the dust sediment in the room and finally clean the air in the room When the fan in the indoor unit does not work the health lamp lights up but the anion generator does not release anion Operation Auto Operation Remote Controller RESET CODE LIGHT LOCK e e O 1 Unit start Link with electronic power Press ON OFF on the indoor unit or press ON OFF on the remote controller unit starts The liquid crystal will display the working state of last time Except Timer Sleep Power Soft and Health airflow 2 Select operation mode Press MODE button For each press operation mode changes as follows Remote controller AUTO COOL DRY FAN HEAT Then Select Auto operation 3 Select temp setting Press TEMP button AA Every time the button is pressed temp setting increases 1 C if kept depressed it will increase rapidly V Every time the button is pressed temp setting decreases 1 C if kept depressed it will decrease rapidly Select a desired temperature 4 Fan speed selection Press FAN button For each press fan speed changes as follows Remote controller al utili Air conditioner is running under displayed wind speed When FAN is set to AUTO the air conditioner automatically adjusts the fan speed according to room temperature 5 Unit stop Press ON OFF button the unit stops About Auto Operation Under the mode of a
8. intended for use by young children or infirm persons without supervision 8 Young children should be supervised to ensure that they do not play with the applience 10 Please employ the proper power plug which fit into the power supply cord 11 The power plug and connecting cable must have acquired the local attestation Cautions Safety Instruction e Please read the following Safety Instructions carefully prior to use e The instructions are classified into two levels WARNING and CAUTION according to the seriousness of possible risks and damages as follows Compliance to the instructions are strictly required for safety use Installation AN WARNING Please call Sales Service Shop for the Installation Do not attempt to install the air conditioner by yourself because improper works may cause electric shock fire water leakage Installation in a inadequate place may cause accidents Do not install in the following place A CAUTION Connect the earth Do not install in the Do not get the unit Check proper place where there exposed to vapor installation of the is any possibility or oil steam drainage securely of inflammable gas leakage around the unit Q S Wed PROHIBITION PROHIBITION Cautions A WARNING When abnormality such as burnt small found immediately Use an exclusive power source with a circuit breaker stop the operation button and contact sales shop
9. FF on the remote controller unit starts The liquid crystal will display the working state of last time Except Timer Sleep Power Soft and Health airflow 2 Select operation mode Press MODE button For each press operation mode changes as follows Remote controller AUTO COOL DRY FAN HEAT Then Select DRY operation 3 Select temp setting Press TEMP button A Every time the button is pressed temp setting increases 1 C if kept depressed it will increase rapidly V Every time the button is pressed temp setting decreases 1 C if kept depressed it will decrease rapidly Select a desired temperature 4 Fan speed selection Press FAN button For each press fan speed changes as follows Remote controller p UI POP OPT BOPT RESET cope LIGHT LOCK e LOW MED HI AUTO Air conditioner is running under displayed wind speed In DRY mode when room temperature becomes 2 C higher than temp setting unit will run intermittently at LOW speed regardless of FAN setting COOL operation starts when room temp is higher than temp setting Spa On reaching temp setting 2 C unit will run in mild DRY mode Ultra low air flow 5 Unit stop Press ON OFF button the unit stops Temp setting 2 C Temp setting 11 Operation Fan Operation Remote Controller 1 Unit start Link with electronic power Press ON OFF button on the indoor u
10. SPLIT TYPE ROOM AIR CONDITIONER OPERATION MANUAL HSU 07RK03 R2 HSU 09RKO3 R2 HSU 12RK03 R2 e Please read this operation manual before using the air conditioner No 0010546296 Cautions Disposal of the old air conditioner Before disposing an old air conditioner that goes out of use please make sure it s inoperative and safe Unplug the air conditioner in order to avoid the risk of child entrapment It must be noticed that air conditioner system contains refrigerants which require specialized waste disposal The valuable materials contained in an air conditioner can be recycled Contact your local waste disposal center for proper disposal of an old air conditioner and contact your local authority or your dealer if you have any question Please ensure that the pipework of your air conditioner does not get damaged prior to being picked up by the relevant waste disposal center and contribute to environmental awareness by insisting on an appropriate anti pollution method of disposal Disposal of the packaging of your new air conditioner All the packaging materials employed in the package of your new air conditioner may be disposed without any danger to the environment The cardboard box may be broken or cut into smaller pieces and given to a waste paper disposal service The wrapping bag made of polyethylene and the polyethylene foam pads All these valuable materials may be taken to a waste collecting center and use
11. arry refrigerant by piercing or performating the air conditioner s tubes with sharp or pointed items crushing or twisting any tubes or scraping the coatings off the surfaces If the refrigerant spurts out and gets into eyes it may result in serious eye injuries Cautions Do not obstruct or cover the ventilation grille of the air conditioner Do not put fingers or any other things into the inlet outlet and swing louver Do not allow children to play with the air conditioner In no case should children be allowed to sit on the outdoor unit Specifications The refrigerating circuit is leak proof The machine is adaptive in following situation 1 Applicable ambient temperature range Maximum D BAW B 32 C 23 C Minimum D BIW B 18 C 14 C Coding Maximum D BWB 43 C 26 C Outdoor Minimum DB 18 C Maximum D B 27 C Minimum D B 15 C Maximum D B W B 24 C 18 C Minimum D BAWB 7 C 8 C Indoor Indoor Heating Outdoor 2 If the power supply cord is damaged it must be replaced by the manufacturer or its service agent or a similar qualified person 3 If the fuse of indoor unit on PC board is broken please change it with the type of T 3 15A 250V 4 The wiring method should be in line with the local wiring standard 5 After installation the power plug should be easily reached 6 The waste battery should be disposed properly 7 The appliance is not
12. d Functions E Clock Set Wer WATUERD xr When unit is started for the first time and after replacing batteries in remote HEALTH controller clock should be adjusted as follows Em 1 Press CLOCK button AM or PM flashes on C Do 2 Press A or Y to set correct time Each press will increase or decrease 1 min If the button is kept depressed time will change quickly RESET CODE LIGHT LOCK e e 3 After time setting is confirmed press SET AM or PM stop flashing while clock starts working E Remote controller s operation When in use put the signal transmission head directly to the receiver hole on the indoor unit The distance between the signal transmission head and the receiver hole should be within 7 m without any obstacle as well Don tthrow or knock the remoter controller When electronic started type fluorescent lamp or change over type fluorescent lamp or wireless telephone is installed in the room the receiver is apt to be disturbed in receiving the signals so the distance to the indoor unit should be shorter Bi Loading of the battery Load the batteries as illustrated right 2 R 03 7 batteries Remove the battery cover Slightly press area and push down the cover as illustrated Load the battery Be sure that the loading is in line with the pole request as illustrated on the bottom of the case Put on the cover again Confirmation indicator After
13. d again after adequate recycling Consult your local authorities for the name and address of the waste materials collecting centers and waste paper disposal services nearest to your house Safety Instructions and Warnings Before starting the air conditioner read the information given in the User s Guide carefully The User s Guide contains very important observations relating to the assembly operation and maintenance of the air conditioner The manufacturer does not accept responsibility for any damages that may arise due to non observation of the following instruction e Damaged air conditioners are not to be put into operation In case of doubt consult your supplier e Use of the air conditioner is to be carried out in strict compliance with the relative instructions set forth in the User s Guide e Installation shall be done by professional people don t install unit by yourself For the purpose of the safety the air conditioner must be properly grounded in accordance with specifications Always remember to unplug the air conditioner before openning inlet grill Never unplug your air conditioner by pulling on the power cord Always grip plug firmly and pull straight out from the outlet All electrical repairs must be carried out by qualified electricians Inadequate repairs may result in a major source of danger for the user of the air conditioner Do not damage any parts of the air conditioner that c
14. dly V Every time the button is pressed temp setting decreases 1 C if kept depressed it will decreases rapidly Select a desired temperature Fan speed selection Press FAN button For each press fan speed changes as follows Remote controller l TEST Wer NT LOW MED HI AUTO Air conditioner is running under displayed wind speed In HEAT mode warm air will blow out after a short period of the time due to cold draft prevention function When FAN is set to AUTO the air conditioner automatically adjusts the fan speed according to room temperature 5 Unit stop Press ON OFF button the unit stops 13 Operation Air Flow Direction Adjustment 1 Status display of air sending direction Vertical flap Pos 6 D Auto swing S 2 Up and down air flow direction For each press of swing button air flow direction on remote controller or on the control panel displays as follows according to different operation modes CCOL DRY FAN 9 WING button remote controller pos 1 gt pos2 gt pos 3 pos4 gt pos6 gt HEAT remote conreoller _ nos 5 gt pos4 gt pos 3 gt pos2 gt posi pos 6 AUTO remote li 1 pos 2 gt pos 3 pos 4 pos5 pos 6 The vertical flap will swing according to the above positions 3 Note When restart after remote turning off the remote controller will automatically memorize the previous set swing position
15. ears SOFT Operation You can use this function when silence is needed for rest or reading Selecting of SOFT operation Press POWER SOFT button Every time the button is pressed display changes as follows A gt N BLANK POWER SOFT Stop the display at In SOFT operation mode fan speed automatically takes LOW To cancel SOFT operation Press POWER SOFT button once POWER SOFT disappears Hints During POWER operation in rapid HEAT or COOL mode the room will show inhomogeneous temperature distribution Long period SOFT operation will cause effect of not too cool or not too warm 18 Operation Health airflow Operation 1 Press ON OFF to starting The liquid crystal will display the working state of last time Except timer sleeping power soft and health airflow Setting the comfort work conditions 2 The setting of health airflow function 1 Press the button of health airflow appears on the display The nether inlet and outlet grills of the air conditioner are closed and the airflow is blown horizontally from the above inlet and outlet grills Avoid the strong airflow blows direct to the body 2 Press the button of health airflow again appears on the display The above inlet and outlet grills of the air conditioner are closed and the airflow is blown vertically from the nether inlet and outlet grills Avoid the strong airflow blows direct to the body 3 The cancel o
16. ed by the P casing expanding or shrinking because of temperature changes Should there be a big noise from air flow in unit operation air filter may be too dirty This is because the system circulates smells Smells are generated from the interior air such as the smell of furniture cigarettes Mist or steam are blown out i During COOL or DRY operation indoor unit may blow out mist This is due to the sudden cooling of indoor air Is power plug inserted Does not work at all Is there a power failure Is fuse blown out Multiple check Is the air filter dirty Normally it should be cleaned every 15 days Are there any obstacles before inlet and outlet Is temperature set correctly Are there some doors or windows left open Is there any direct sunlight through the window during the cooling operation Use curtain e Are there too much heat sources or too many people in the room during cooling operation Poor cooling 26
17. ers on the top of the unit PROHIBITION Parts and Functions mA h N ndoor uni OPERATE COOL DRY HEAT TIMER HEALTH Display board pex Rem RED GREEN YELLOW The conversion of pilot light s colors will be displayed as the figure under different operation models Display board el Air filter inside Anion generator inside Inlet grille Vertical flap Use remote controller to adjust up and down air flow Dor t adjust it manually Horizontal louver adjust left and right air flow L Power plug Outdoor unit oO E 3 z HSU 07RK03 R2 HSU 09RKO03 R2 HSU 12RK03 R2 1 OUTLET 3 CONNECTING PIPING AND ELECTRICAL WIRING 2 INLET 4 DRAIN HOSE 5 Parts and Functions ON ia ES Lu B PMID PMO 1 SWING button Used to select up or down air sending direction 2 HOUR button Used to set clock and timer setting 3 MODE button Used to select opreation mode AUTO COOL DRY FAN HEAT 4 HEALTH button Used to set healthy operation 5 CLOCK button Used to set correct time 6 TIMER button Used to select TIMER ON TIMER OFF TIMER ON OFF 7 RESET When the remote controller appears abnormal use a sharp pointed article to press this button to reset the remote controller normal 8 HEALTH display 9 SLEEP dis
18. f the health airflow function Press the button of health airflow again both the inlet and RESET cone USHT Lek outlet grills of the air conditioner are opened and the unit goes 08 on working under the condition before the setting of health airflow function After stopping the outlet grille will close automatically Notice Cannot pull direct the outlet grille by hand Otherwise the grille will run incorrectly If the grilleis not run correctly stop for a minute and then start adjusting by remote controller Note 1 After setting the health airflow function the position of inlet and outlet grills is fixed 2 In heating it is better to select the I mode 3 In cooling it is better to select the mode 4 In cooling and dry using the air conditioner for a long time under the high air humidity a phenomenon falling drips of water occurs at the outlet grille 5 Select the appropriate fan direction according to the actual conditions 19 Operation Emergency and Test Operation Emergency operation e Use this operation only when the remote controller is defective or lost When the emergency operation switch is pressed the Pi sound is heard once which means F the start of this operation e In this operation the system automatically selects the operation modes cooling or heating according to the room temperature When machine is running in emergency the set value of
19. ff the power supply cord 3 Cleaning the body 4 Take out the batteries from the wireless remote controller 24 Maintenance Before Setting in High Season a 1 Cleaning the standard air filter Operation without filter may cause troubles Be sure to attach both right and left filters prior to the operation Each of them are of different shapes 2 Connecting the earthing cable AA Caution e Incomplete earthing may cause an electric shock EARTHING A Caution e After brush away dust at the plug insert the plug of the power supply cord into the outlet completely In case of using exclusive circuit breaker switch on the circuit breaker NO WET HAND J 25 Trouble shooting Before asking for service check the following first The system does not restart e When unit is stopped it won t restart immediately immediately until 3 minutes have elapsed vA to protect the system When the electric plug is pulled out and reinserted the protection circuit will work for 3 minutes to protect the air conditioner During unit operation or at stop a swishing or gurgling noise may be heard At first 2 3 minutes after unit start this noise is more noticeable This noise is generated by refrigerant flowing in the system Normal During unit operation a cracking noise may dulce be heard This noise is generat
20. nit or press ON OFF on the remote controller unit starts The liquid crystal will display the working state of last time Except Timer Sleep Power Soft and Health airflow 2 Select operation mode Press MODE button For each press operation mode changes as follows Remote controller AUTO COOL DRY FAN HEAT Then Select FAN operation 3 Fan speed selection Press FAN button For each press fan speed changes as follows Remote controller 18 0c adl LOW MED HI 4 Unit stop Press ON OFF button the unit stops About FAN operation In FAN operation mode the unit will not operate in COOL or HEAT mode but only in FAN mode AUTO is not available in FAN mode And temp setting is disabled In FAN mode SLEEP operation is not available 12 Operation Heat Operation Remote Controller RESET CODE LIGHT LOCK ee O 1 Unit start Link with electronic power Press ON OFF button on the indoor unit or press ON OFF on the remote controller unit starts The liquid crystal will display the working state of last time Except Timer Sleep Power Soft and Health airflow Select operation mode Press MODE button For each press operation mode changes as follows Remote R Vork e AUTO COOL DRY FAN HEAT Then Select HEAT operation Select temp setting Press TEMP button AN Every time the button is pressed temp setting increases 1 C if kept depressed it will increases rapi
21. of Air purifying Filter 1 Open the Inlet Grille p Open the inlet grille by pushing each ends of the inlet grille upward use thumbs to push up 2 Detach the standard air filter Slide the knob slightly upward to release the filter then withdraw it 3 Detach old Air Purifying Filter Detach old Air Purifying Filter 3 Attach new Air Purifying Filter Put air purifying filter appliancesinto the right and left fliter frames as white side face to LIO the front ae 3j 4 Attach the standard air filter Necessary installation 5 Close the Inlet Grille Close the Grille surely NOTE The air purifying filter of multi lights touching intermediary and the electrostatic air purifying filter accessories with machine will be used based on real situation The air purifying filter of multi lights touching intermediary will be solarized in fixed time In normal family it will be solarized every 6 months The solarization time will last no less than 8 hours under the state of abundant sun 23 Maintenance To Keep Your Air conditioner in Good Condition after Season 1 Operate in cooling mode for 2 3 hours To prevent breeding mold or bad smell be sure to operate at the designated temperature of 30 C cooling mode and High speed fan mode for 2 3 hours 2 Put o
22. play 10 SWING UP DOWN display 11 LOCK display 12 FAN SPEED display Per mer mer LOW MED HI AUTO 13 TIMER ON display 14 TEMP button Used to select your desired temperature 15 Operation mode display Operation mode AUTO COOL DRY HEAT FAN Remote controller amp 7 3 xt 16 CODE display 17 POWER SOFT display 18 Left right air flow display 19 TEMP display Remote controller to display the TEMP setting 20 TIMER OFF display 21 CLOCK display 22 FAN button Used to select fan speed LOW MED HI AUTO 23 ON OFF button Used for unit start and stop 24 SLEEP button Used to select sleep mode 25 HEALTH AIRFLOW button Used to set the healthy airflow mode 26 SET button Used to confirm timer and clock settings 27 POWER SOFT button 28 LOCK Used to lock buttons and LCD display If pressed the other buttons will be disabled and the lock condition display appears Press it once again lock will be canceled and lock condition display disappears 29 LIGHT button Colorful display bar of the controlling indoor machine is on and extinguished 30 CODE Used to select CODE A or B with a press A or B will be displayed on LCD Please select A without special explanation NOTE 1 The following functions and related displays are not available 8 69 and G9 2 Cooling only unit do not have functions and displays related with heating 6 Parts an
23. pressing power ON OFF if no display reload the batteries Note Full display or unclear display during operation indicates the batteries have been used up Please change batteries Used two new same typed batteries when loading Ifthe remote controller can t run normally during operation please remove the batteries and reload several minutes later Hint Remove the batteries in case unit won t be in usage for a long period If there are any display after taking out just need to press reset key Operation Health Operation Remote Controller 1 Unit start Link with electronic power Press ON OFF on the indoor unit or press ON OFF on the remote controller unit starts The liquid crystal will display the working state of last time Except Timer Sleep Power Soft and Health airflow Then set up the comfortable working state 2 Select operation mode Press HEALTH button For each press 777 is displayed The pilot light of healthy process on the display board is on hence healthy process begins When indoor wind machine is running it has healthy process function It s available under any mode eo Unit stop Press HEALTH button the healthy function stops The pilot light of healthy process on the display board is extinguished BRIEF INTRODUCTION TO HEALTH OPERATION The anion generator in the air conditioner can generate a lot of anion to effectively balance the quantity of position and anion
24. temperature and wind speed couldn t be altered meanwhile it can t operate for dehumidifying or under timing mode Test operation Test operation switch is the same as emergency switch Use this switch in the test operation when the room temperature is below 16 C do not use it in the normal operation Continue to press the test operation switch for more than 5 seconds After you hear the Pi sound twice release your finger from the switch the cooling operation starts with the air flow speed Hi Removal of the restriction of emergency or test operation e Press the emergency operation switch once more or manipulate through the remote controller the Pi sound the emergency or test operation is terminated When the remote controller is manipulated it gets the system back to the normal operation mode 20 Maintenance For Smart Use of The Air Conditioner Setting of proper room Do not block the air inlet temperature or outlet tek S Close doors and windows Use the timer effectively during operation EEE DECOR wt During cooling operation prevent the penetration of direct sunlight with curtain or blind If the unit is not to be used for a long time turn off the power supply main switch
25. uto operation air conditioner will automatically select Cool or Heat operation according to room temperature Operation Cool Operation Remote Controller MODE HEATHARFLOW SLEEP 2g coco RESET CODE LIGHT LOCK O 1 Unit start Link with electronic power Press ON OFF on the indoor unit or press ON OFF on the remote controller unit starts The liquid crystal will display the working state of last time Except Timer Sleep Power Soft and Health airflow Select operation mode Press MODE button For each press operation mode changes as follows Remote controller AUTO COOL DRY FAN HEAT Then Select COOL operation Select temp setting Press TEMP button A Every time the button is pressed temp setting increases 1 C if kept depressed it will increase rapidly V Every time the button is pressed temp setting decreases 1 C if kept depressed it will decrease rapidly Select a desired temperature Fan speed selection Press FAN button For each press fan speed changes as follows Remote controller Air conditioner is running under displayed wind speed When FAN is set to AUTO the air conditioner automatically adjusts the fan speed according to room temperature Unit stop Press ON OFF button the unit stops 10 Operation EE Dry Operation 1 Unit start Link with electronic power Remote Controller Press ON OFF button on the indoor unit or press ON O
Download Pdf Manuals
Related Search