Home

Haier HRF-305 User's Manual

1. A 11foot cover is put at the back of the foot and fasten its left side by wood screw 1 piece Fasten the other parts of the foot after the refrigerator door is installed 35 Installation Sequences Dismantling of the upper fixing plate Open the refrigerator door and draw out upward the 2 upper fixing plate cover of 6 the upper fixing plate 2 each in the upper and lower door _ they are stored separately Loose 2 hex screw fixing 2 upper fixing plate 2 each in the upper and lower door _ they are stored separately Raise and disassemble 2 upper fixing plate on the refrigerator cabinet door 2 each in the upper and lower door _ they are stored separately oF The upper fixing plate is used when you install refrigerator cabinet door for installation method please refer page 15 17 Upper Fixing Plate2 disassembled status refrigerator door Upper Fixing Plate 2 Assembled status 36 Installation Sequences 5 Connecting the upper fixing plate and refrigerator cabinet door Put the disassembled 2 upper fixing plate and cabinet door as shown in the diagram turn the hex screw a little Draw the cabinet door station meter on the 2 upper fixing plate to the internal base line of the upper side panel the internal base line of the upper side panel cabinet door station meter after aligning the height of upper side pan
2. Don t store gasoline and other flam high corrosive acid and alkali must mable materials near the fridge It may not be put in the fridge cause explosion or fire disaster After the fridge is powered don t try Don t hang on the fridge door to play to clean or touch any condenser under It may make the fridge falling down or cause freezer drawers injury It may freezer skin and cause injury Special attention shall be given to child z Safety Precautions Don t wash or rinse the fridge with water or put the fridge in a humid place If the insulation is not good it may cause elec tricity leakage When there is power failure or you clean the fridge and cut off its power you have to re connect the fridge at lest in 5 minutes Otherwise overloaded lt gt comes vulnerable to malfunctions Og there is dust dirt humidity or splashed water Otherwise it will effect the performance of the fridge or even become cause of injury shocking or fire disaster don t put the fridge in a place where Don t put burning candle dog end Nobody is allowed to disassemble re pair or modify the fridge except the professionals When you discard the fridge you have to dismantle the fridge doors If child play with these doors there is a po tential of accident Ale inside on top or near the fridge or fridge cabinet Safety Precautions It is not goo
3. depth of the refrigerator cabinet door the upper end adjusting method of the door Fix the upper hook of the refrigerator door referring refrigerator cabinet door installation method Use spanner to turn a height adjusting nut to adjust height X About 5mm In case it is difficult to adjust check the left and right clearance of the upper fixing plate and position Loose b the left and right adjusting nut a bit and move the left and right of the refrigerator cabinet door to adjust the left and right position Y about 5mm In case it is difficult to adjust check the left and right clearance of the upper fixing plate and position Loose c the depth adjusting nut a bit move the refrigerator cabinet door and adjust the depth and then tighten about 3mm In case it is difficult to adjust check the left and right clearance of the inner line of the refrigerator cabinet and position c Lower end adjusting method of the door Loose the screw a bit and adjust the depth Z and then tighten it Adjust the rest holes of the lower fixing plate with _ wood screw after adjusting the left and right of the refrigerator cabinet door depth adjustment Z gt furniture door Further fixing fixed screw fixed screw 39 Installation Sequences wind up work Insert 6 upper fixing plate cover into upper fixing plate 2 places refer to Figure A on Page 19 Insert 10 upper fixing cover into upper lower left right
4. the real temperature of the fridge fresh food compartment freezer is higher than the set temperature The alarm indicator J is on the display of temperature raise a1 of the fresh food compartment c of the freezer flash with alarming sound Press fresh food compartment temperature button A and cooling speed button C at the same time the alarm disappear When the temperature is reached the alarm display J stops flashing If the alarm display J still show after several hours contact the nearest after sale service hanch Functions and Temp Setting Method Functions and Temp Setting Method 12 Auto Diagnosis Display Function Sensors in the fridge can guarantee effective control of the fridge The digital display will show 15 Alarm Function Type F1 F2 F3 F4 when any sensor detect abnormal temperature The fridge will still When correct buttons are selected there will be buoyant reminding sound to tell you operate even with these abnormality display If you cannot solve the problem contact the that you make right choice nearest after sale service center F1 will show in the fresh food compartment temperature display a1 when the evaporator is 2 Power ON OFF faulty or its ambient temperature is above 42_ Press power button F 3s when power is on then all display will disappear and power The Quick refrigerating function can not be used at that time is off F2 will show in fresh food compartmen
5. and low temperature antibiosis function When it is in Quick Refrigerating setting status 1 4 level you can set freezer temperature intelligence quick freezing time etc Setting of Quick Freezing Press the cooling speed Button B the quick refrigerating indicator b2 is on temperature display of the freezer c show 00 and flash Every time you press cooling speed button B it will circle to display level 1 to level 4 it will go back to 00 after it reaches level 4 00 _ 01 _ 02 _ 03 _ 04 _ 00 Maximum level 4 wait 5s in the selected level to finish level setting it will resume to display present temperature of freezer after it is set press cooling speed button B it will show that it is in quick freezer b2 status and it can be re set If you don t want to use quick freezer set the quick freezer level to 0 Reference 00 Level Quick freezing function is off and resumes previous setting level 01 Level Quick Freezing Function start within 15 hours 02 Level Quick Freezing Function start within 30 hours 03 Level Quick Freezing Function start within 45 hours 04 Level Quick Freezing Function start within 60 hours When it is in Quick Freezing Setting status level 1 4 you can not set freezer temperature low tempera ture antibiosis function When it is in Quick Freezing Setting status level 1 4 you can still set fresh food compartment temperature intelligence quick ref
6. flash display is end Otherwise it may cause malfunction in the operation panel 10 3 Functions and Temp Setting Method day wig don Super Freezing LILI g LILI Fuzzy _ see PCA sue GLb dJ 2 E Setting of Quick Refrigerating Press the cooling speed Button B 3s the quick refrigerating indicator b1 is on temperature display of the fresh food compartment a1 show 00 and flash Every time you press cooling speed button B it will circle to display level 1 to level 4 it will go back to 00 after it reaches level 4 00 _ 01 _ 02 _ 03 _ 04 _ 00 _O Maximum level 4 wait 5s in the selected level to finish level setting it will resume to display present temperature of fresh food compartment after it is set press cooling speed button B it will show that it is in quick refrigerating b1 status and it can be re set If you don t want to use quick refrigerating set the quick refrigerating level to 0 Reference 00 Level the quick refrigerating function is off 01 Level the Quick Refrigerating function start within 1 5 hour 02 Level the Quick Refrigerating function start within 3 hours 03 Level the Quick Refrigerating function start within 4 5 hours 04 Level the Quick Refrigerating function start within 6 hours When it is in Quick Refrigerating setting status 1 4 level you can not set the temperature of the fresh food compartment
7. of the cabinet first connect the power before put the refrigerator cabinet into its place 3 For safeties put the power switch in off position and the switch of the whole room as well Draw the cord from the hole at the back of the refrigerator cabinet Put the refrigerator into the cabinet The clearance adjusting sheet shall stick tightly with side panel The front of the upper fixing plate shall align with the end surface of the side panel The left and right clearance between refrigerator and the cabinet shall be kept the same Adjust hex screw to adjust the refrigerator s height and adjust the uprightness and horizon Screwdriver can be found in the installation kit upper surface Plane Diagram Refrigerator Refrigerator cabinet End surface of clearance adjusting sheet Front line of side surface Upper fixing plate e side surfaces of hinge shall be fastened by screws _ The sid rf f hi hall be fastened b 2 pieces 1 screw is fastened on the first hinge and another one on the 4 hinge Fasten the other hole on hinges after installation of the refrigerator door 34 Installation Sequences The front of the refrigerator cabinet door shall be adjusted by square or steel rule and A and B shall be the same Upper surface Plane Diagram Square Position Adjustment et
8. performance of the fridge ES v i as Don t put the fridge in a extreme cold or warm place especially outside a room which may affect the performance of the fridge Usage Instruction Preparation 1 Take off foams and adhesive tapes fixing the fridge 2 Check the materials inside the fridge User Manual Pin Discharge Pin Wine shelf Egg Plate Ice Plate 1 1 1 1 1 3 Clean the fridge before usage Refer Page 23 4 To reassure the normal and stable operation of the fridge power the fridge only after 30 minutes of cleanness lt lt When use the fridge the first time after installation power the fridge also 30 minutes after installation X_ Record the fridge name and model in the Warranty for reference 7 Operation Check Power Connection After the plug is connected to power the fridge starts automatically Power the fridge after power off press power button 3s the green indicator is on the fridge start to operate Temperature Setting Refer to Page 12 Il Even if you don t set the temperature the fridge can operate When you want to re set temperature of the fresh food compartment Press Fresh Food Compartment Temp Setting A of the fresh food compartment 3s The temperature setting part of the fresh food compartment flashes Press Fresh Food Compartment Temp Setting A the temperature will change When the expected temperatu
9. 8 hinge hold sheet and change the position of hinge That is to insert 8 hinge hole sheet to the hinge fixing hole on the other side Figure G Assembly Method 42
10. Haier Built in Refrigerator HRF 305 Read the Safety Precautions and using methods carefully before using the refrigerator Keep this manual in a proper place so that you can refer to it at any time We may change the product profile and specification to improve its quality without informing cus tomers in advance Contents Safety Precautions Usage Notice Operation Check Main Sections Introduction Function amp Temp Setting Refrigerator Usage and Food Storage Cleaning Stoppage Problems and solutions Service Request and Issues that required to be confirmed Product Specifications Installation Diagram Warranty Installation Instruction 1 5 10 15 18 20 21 22 23 24 25 26 27 28 28 28 29 41 Safety Precautions You shall strictly behave according to the following precautions to prevent disasters and losses According to the expected disaster damage and emergency level we divided the precautions into 3 classes which are marked by the following 3 symbols N Symbol Explanation Any behaviour that is against these precautions may cause serious injury even death Note Any behaviour that is against these precautions may cause slight injury or product damage This symbol reminds for the issues and operations that may caus
11. d to put too much materials Don t put heating device near the or food on top of and inside the fridge fridge which may block the cooling air It may cause fire disaster or electric shocking circulation accident e Don t spray benzene lacquer thinner J After you clean the fridge close its and alcohol etc inside the fridge don t the cabinet doors Food stored in the rinse the fridge cabinet wood section fridge or other objects shall not hinder the close of the fridge daor After the fridge door is closed check In case there is abnormal smell sound or smoke etc contact our after sale ser its sealing vice branch Safety Precautions Don t put unstable or heavy materials or water container etc on the top of the fridge It may cause fire disaster electric shocking accident and the falling materials may also cause injury Bottled beer or soft drink shall not be put inside the freezer which may cause bottle break Usage Instruction This product adopts AC 220V voltage 3 The plug shall be connected to sole purpose 220V socket Installation Method This product is usually a built in type fridge put in fridge cabinet When you want to block up the fridge on a level floor you have to use solid and flameproof materials and you must not use foam used during the transportation of the fridge Don t put the fridge near a heat source or under direct sunshine which may affect the
12. e dangers A You shall read carefully about the parts that are with this symbol and do accordingly to u prevent accidents j Connecting the power cord using exclusive socket This fridge uses 220 240V 50Hz power supply Large voltage fluctuation may cause no start up Use qualified plug on this fridge and don t cut of the fridge and malfunction of temp adjusting the plug device and transformer as well An auto 750W plus stabilizer shall be installed in such case R Don t damage the cord In case the cord is damaged Don t use too much power when drawing the cord hold the plug tightly and draw it out carefully Don t put the refrigerator on the cord and try to avoid stepping on the cord When you move the fridge be careful don t dam age the cord Sel bas A x It is prohibited to use damaged cord which may cause shocking or short circuit and fire disaster When the cord is damaged find help in desig nated after sale service center Safety Precautions In case there is gas or flammable gas Don t put socket transformer or mi leakage crowave on top of the fridge and it is Close the valve not allowed to use any electrical appli Open windows and doors ances inside the fridge The spark when you draw or insert plug of fridge or other electric appliances may cause explosion and fire disaster Bi Oo le Wy cs Flammable explosive articles and
13. e light cover to direction and draw it out from the square Draw the cover to direction holding 2 ends and take down the cover Turn counter clockwise to take off the damaged light and turn on new one clockwise Light cover installation put cover back and insert anti drop pin 16 Fresh Food Compartment Usage and Food Storage Cool hot food naturally before put them into the fridge If you put hot food into the fridge they will affect nearby food and increase power consumption Eliminate humidity in food before store them in the fridge Seal food before storage It can prevent water evaporation odor tainting and keep freshness Food shall be classified and stored Classify food and put food that you will eat soon in front and food that you will not eat soon at the back to store food for a longer time Don t put too much food in the fridge Don t jam the fridge with food good cooling air ventilation can make sure a good refrigerating result Don t put food against inner wall Don t store food against inner wall If food touches the wall after food is frozen it will stick together with the inner wall 17 Fresh Food Compartment Usage and Food Storage Store vegetables against their growing direction y f 2 wie Cut leaves of radish species Some nourishment N x 117 may be lost Put egg into egg holder Defrost frozen food in the fresh food compartment Cooling air steamed by
14. el separate the upper fixing plate and the cabinet Refer to page 14 Put the refrigerator cabinet door backside up flatly on a clean floor and put 2 upper fixing plate as shown tightly against the upper end line of furniture adjust the position and align the central lines of upper fixing plate and cabinet door and fix with wood screws 10 places each Cabinet door p EA i Ke ce Position Y station l i f l l gd l l l l backside of refrig rator cabinet door backside of refrigelator cabinet door Refrigeratof cabinet door Upper central line Refrigeratoh cabinet door Lower central line Draw out the station meter from the upper fixing plate 37 Installation Sequences 6 Installation method of the refrigerator cabinet door Open the refrigerator door hang the refrigerator cabinet door on the height adjusting bolt in the upper side of the refrigerator and fix with hex nut it shall not be too tight and it shall be movable 2 in the left and right Close the door and the screw shall not be tightened and adjust the left and right clearance of the upper end bolt Height adjusting bolt Check the uprightness and level turn slightly 16 fixing screw of the lower fixing plate and 14 wood screw 4 places 14 wood plate fixing screw 16 fixing screw of the lower fixing plate 38 Installation Sequences 7 adjustment method of the height left and right
15. ess freezer temperature button C to adjust minute it will change 1 minute every time you press once Wait 5s to change to the set time The time can be set when it is in ambient temperature display status or present temperature display status the setting scope of hour is 00 23 and the minute is 00 59 10 Setting of Timer Press cooling speed button B and intelligence button D at the same time the default timer setting 00 00 is shown Press once the fresh food compartment temperature button A it will change 1 hour Press once the freezer temperature button C it will change 1 minute Wait 5s the time will automatically change to the set time and timer display N will show The ambient temperature and present time cannot show until the end of set time of the timer When the timer goes to 00 00 the timer display N disappear and the alarm continue 20s and the present time and ambient temperature display will resume If you want to close the 20s alarm press cooling speed button B and intelligence button D at the same time You also have to press cooling speed button B and intelligence button D at the same time to close timer function or to re set And the timer display N disappear and the function is cancelled the setting scope of hour is 00 23 and the minute is 00 59 11 Setting of Abnormal Temperature Alarm n case that the door of the fridge is not close well or large quantity of food is put in the fridge
16. ezer capacity limitation Freezing effect becomes worse when you put too much food inside the freezer Don t store food over freezer limitation 19 Freezer Usage amp Food Storage Cool hot food naturally before put them into the fridge If you put hot food into the fridge they will affect nearby food and increase power consumption Put food in small bag each bag shall be less than 2 5kg Freeze food after packing Write date on surface of the frozen food It is not suggested that you freeze again the defrost food the freshness will be affected 20 Clean Cleaning work Clean the fridge periodically otherwise stored food may have bad smell Shut off the fridge for safety K Soak soft cloth in hot water or detergent and then clean the fridge kI When you use neutral detergent you must use clean cloth to wipe Don t use grinding powder hard brush gasoline bleacher boiled water acid materials otherwise Note the fridge surface and components may be damaged Don t rinse while clean the fridge it will affect anti shocking fi function Wipe buttons light with soft cloth Juice and liquid on door gasket may shorten its life span you have to clean it when there is juice or liquid on door gasket 21 Clean Auto Defrost of Fresh Food Compartment The fresh food compartment can do auto defrost The ice is melted into water and discharged Discharge pin A Don t block hole
17. frozen food can decrease the fresh food compartment temperature and reduce power consumption Muskmelon banana etc have metabolism even if in refrigerating status so you don t have to put them in the fridge In winter the room temperature may drop to 0 10 C and the fresh food compartment temperature will drop correspondingly Vegetable and fruit at the bottom will be frozen Note so put them on top 18 Freezer Usage amp Food Storage Freezer is used to store food for a long time Temperature in the freezer is low and it can keep food for a long time but you have to take care about food available period You can find freshness period and available period of different food in the following Category freshness period longest storage period A month month chicken beef mutton shrimp 4 9 bun dumpling chop ice 4 6 cake bread sliced meat butter 2 6 crab seafood viscera ice cream 1 3 J Refer to food available period for details and the freshness may be also different The above mentioned storage time is when food is stored in common freezing status 14 24 Freshness decreases by time It is suggested that food is consumed within the freshness period Making Ice Put water into the ice tray Take out the ice tray with a bit strength but don t knock the ice tray Wait a while and twist the ice tray a bit and ice will drop Don t store food over the fre
18. g start up or stop similar with that of automobile When the fridge operates the first time the temperature of the When there is dew out side the fridge The fridge is put in humid place or during summer especially rain season it is humid and hot there will be dew on surface of the cold fridge wipe them with dry cloth fridge and compressor may increase and the operation time is lengthened 25 Problems and Solutions The installation position affect vibrating sound and its power Sound can be There is heat radiation at the back of the fridge and the temperature there is high which is normal The power consumption in the product specification i When temperature and humidity are high 32 and 70 frost will appear measured after it is in operation for 24 hours in specific temperature according to national in the fridge lower the temperature setting standards The gurgling sound when When the ambient temperature refrigerant flows in the is lower than 8 the fresh food compartment can stop operation Adjust the fresh food compartment temperature to 7 and it can evaporator is like water flow save energy 26 reduced when the fridge is good leveled Service Request and Issues that require to be confirmed as Phenomenon _ Issues that require to Measures be confirmed The fridge Is it power failure Check whether other appliances work doesn t work Is the plug in
19. her parts give the compressor instruction and this function will minimize the compressor s load and the compressor start to work 8 minutes after the fridge resumes work 14 15 Fresh Food Compartment Usage and Food Storage Store the short term stored or frequent food is the fresh food compartment The temperature in the fresh food compartment is 2 7 the eA fresh food compartment keeps food fresh shorter than the Loney freezer does Ey Storage Space of Different Foods The temperatures inside the fresh food compartment are different E store food in proper place section is with the lowest temperature Flavor food tin I W bread tin milk and tofu cooked meat sausage fruits vegetable and salad etc egg oil tin flavor and dairy products 0 soft drink and bottled food food needs to be frozen Shelves and Bins are Adjustable You can adjust the height of shelves and bins of the fresh food compartment You shall be careful when you adjust height which cause injury or damage because of falling down or collision Light and its Change Light Specification 220 240V 15W using of light over 25W is prohibited When you change light Pull out the power to stop power supply Press the anti drop pin of th
20. his is the installation sequence of right open cabinet HRF 305 2 Preparations before freezer Cabinet nstallation A P cl djusting sheet is alread ted to hinge 4 pi Move the hinge from right to left for the left open cabinet and install accordingly Clearance adjusting sheet is already connected to hinge 4 pieces They have to be take off when T18 cabinet is used When you install T15 furniture they don t need to be taken off If you want to open from the left swap the t upper and the lower parts 1 Basic Dimensions When you change to left open door install the hinge in the left Refrigerator cabinet Width outside Width inside The hinge positions shall be swapped Confirm the right angle of every refrigerator cabinet L Upper R Upper Confirm the refrigerator cabinet air inlet and outlet LiLower R Lower refrigerator cabinet door Upper Width Height Confirm the fixing plate in lower part of component is installed well Refrigerator cabinet door Lower WidthOHeight iene Draw the cord from the hold at the back of the fomgerter p IPutthe refrigerator into the l cabinet 32 33 Installation Sequences 3 Put the refrigerator into the cabinet 1 Put the refrigerator into cabinet don t squeeze the cord Damaged power cord may cause fire disaster 2 Connect the power If the socket is at the back
21. ng Display F Power c Freezer Temp Display G Ambient Temp and Time Display d Intelligence Function Dis H Ambient Temp Change Display play Time Display Present time Set time e1 Low Temp Antibiosis In J Time setting function display dicator e2 Low Temp Antibiosis Dis lt play J Temp Setting 1 2 Note Fresh Food Compartment Temp Setting Press fresh food compartment temp setting button A the display of present set temp of the fresh food compartment a1 begin to flash The temp will increase by 1_ every time you press fresh food compart ment temp setting button the fresh food compartment temp setting scope 2_ 7_ Wait 5s to finish the temperature setting after you find the expected temperature The flashing fresh food compartment setting temperature disappear and the present temperature of the fresh food compartment will show Freezer Temperature Setting Press freezer temperature setting button A the display of present set temp of the freezer c begin to flash The temp will increase by 1_ every time you press fresh food compartment temp setting button the freezer temp setting scope 14_ 24 Wait 5s to finish the temperature setting after you find the expected temperature The flashing freezer setting temperature disappear and the present temperature of the freezer will show Set the temp of fresh food compartment and freezer compartment after other setting is finished and
22. ot food in the fridge is the stored food congested The stored food shall not affect the close of thedoor Cool the hot food before store it There shall be clearance between stored food 27 Products Specifications Model HRF 305 Climate Type ST N SN Anti shocking protection Classification l Total Capacity 273l Fresh food compartment Freezer capacity 1991 741 Rated Voltage 220V Rated Frequency 60Hz Rated Motor Power 120W Refrigerant R600a 55g Cooling Capacity 10kg 24h Weight 70kg LengthXDepthXHeight mm 540X544 X 1773 Power cord connection mode Y p Circuit Diagram A Plug B Switch C Light E Fan F Electric Solen G Sensor1 Sensor3 J Sensor4 K Over voltage Stop Device M PTC N Capacitor 28 D Mother Board H Sensor2 L Compressor Note HRF 305 npe ma a ie Ses During transportation and installation do not squeeze power cord Damaged power cord may cause fire disaster Do not dismantle the refrigerator except it is indicated in the manual Otherwise there may be electrical shock fire hazards After installation do not throw this instruction and keep it properly together with the refrigerator manual After you connect the power cord during and afte
23. r installation you have to confirm the refrigerator can function well It is better that the installation work is carried out by 2 or more personnel or hazard may happen 29 Combination Refrigerator HRF 305 Combination Refrigerator HRF 305 Exploded View Components list 1 sheet to adjust clearance 2 Upper fixing board 3 Lower fixing plate 4 side gasket rubber 4 piece connected 3 categories 2 pieces connected 4 pieces connected 2 pieces 5 upper pad Steel 6 upper fixing board cover 7 hinge cover 8 Hinge hole sheet i I l 1 Connected 2 Connected 4 Connected 6 Connected i 1 l 9 operating board left 10 upper fixing board cover and right cover L amp R 11 foot cover 12 upper gasket bolt cover hh u me N 4 ii ae 15 i ae Hinge opposite side hinge side 2 categories 1 each 4 2 2 Connected 13 furniture door Hinge 14 wood screw 15 Hinge fixing screw 16 lower fixing board Hole trims horizontal screw UP 2 20 um 3 8 pom Epo 5 2 11 2 it is used when connecting door with 3x12 cabinet as per furniture hinge hole x 4x16 5x16 5 32 8 4 There are two type of sheet thickness T15 and T18 of the kitchen furniture cabinet 30 31 Installation Sequences Installation Sequences T
24. re appears stop pressing the button and wait The temp setting display stop flashing instead it shows the present temperature of the fresh food com partment Details for setting of freezer temperature and others refer to Page 12 16 Food Storage After the fridge is powered don t put food immediately into the fridge Put food in the fridge after the tempera ture in the fridge drops substantially It will take a while for the temperature in the fridge to reach the set value after you A change the temperature setting Note The time to reach setting temperature is related to ambient temperature and the quantity of stored food 8 Major Sections Introduction Operation Panel Light FAN Shelves of fresh food compartment Crisper Freezer Temperature Setting 14 24 Dairy Bin Bottle amp Tin Bin Functions and Temp Setting Method After the fridge is powered power button indicator and function indicator will on al GHI A Fresh Food Temp set the temperature of fresh food a1 Fresh Food Compartment compartment fresh food compartment ON OFF button Temp Display B Cooling Speed button to adjust the cooling speed of the a2 Refrigerating Function fresh food compartment and the freezer Display C Freezer Temp Set the freezer temperature b1 Quick Refrigerating Dis D Intelligence play E Low Temp Antibiosis b2 Quick Freezi
25. ridge Note Wait at lest 5 minutes after power is resumed 23 Stoppage When you are out for a while or on holiday For short period take out food that is easy to degenerate and adjust to proper temperature For long period draw out the power plug and take all food out clean the fridge and open the doors Even if you don t use the fridge for a long time and you can still use the low temperature antibiosis function Refer to Page 14 During Transportation Take out all stored food After shut off power draw out power plug Fix the plug properly Fix shelves boxes bins etc with tape Close the doors and seal them with tape The inclination during transportation shall be within 45c0 other wise the cooling system will be affected A Don t lie down the fridge in any case Note I llc 24 Problems and Solutions when you hear clatter rattle sound The compressor continues to work for a long time It is sound when some part of the fridge begin to When large quantity of food is stored or the ambient operate or refrigerant flows which is not faulty temperature is high the operation time of the compressor becomes longer When the fridge operates the first time the sound is maybe a bit larger to lower the temperature After the temperature drops to some extent the sound will become smaller When you hear sound like delerler deke onom it is from compressor an durin
26. rigerating time etc 11 Functions and Temp Setting Method i B a GHI c i D a F Fridge Temp Fregzer Temp Stand by Function O Super Erepzing a E la la Fu y ALARM SURER 5 Setting of Intelligence Function Press Intelligence Button D the indicator d is on and the intelligence function starts to work When you want to cancel the intelligence function press the Intelligence Button D 3s the intelligence indicator d is off and the function is cancelled When Intelligence is selected you can not select functions like quick freezing quick refrigerating fresh food compartment temperature freezer temperature low temperature antibiosis etc 6 Setting of Low Temperature Antibiosis Function Bad smell in the fridge is mainly because of the reproduction of bacteria and this function can reduce bad smell in the fresh food compartment and freezer The low temperature antibiosis function can only be set after some functions like the intelligence quick refrigerating quick freezing fresh food compartment temperature etc are cancelled Press the low temperature antibiosis button E the low temperature antibiosis indicator e2 is on the fresh food compart ment temperature is automatically set to 15_ while that for freezer is 18_ A After the low temperature function is set timer function is in stand by Note 7 Switch of Fresh Food Compartment When fresh food compartmen
27. s on crisper if it is blocked open it with discharge pin Note Freezer Auto Defrost After long time usage water is accumulated on the evaporator and make it easy to frost You have to scrape the frost with little plastic scoop You have to seal well the stored food to prevent water leakage and frost Shut off power first before defrosting Put a bowl of hot water on evaporator to accelerate the process Wipe the melted water with clean cloth gaskets around doors are easy to be contaminated clean them often Electrical tool or sharp instrument are prohibited to be used to defrost It is better to Note Use recommended tools 22 Stoppage When there is power failure Food can be stored several hours without problem even if there is power failure in summer Don t put any food inside the fridge after power failure and don t open door often as well When you get power failure notice in advance prepare some ice cube and put them inside the fridge in the upper part of it The fresh food compartment temperature will ascend when there is power failure Note of breakdown which will affect the freshness of food Stoppage If you want to stop using the fridge for a while clean the fridge with methods mentioned thereinbefore After long time no usage and there is no cold air in the fridge maybe there is bad smell of food when you open doors Don t shut off power randomly which may affect the life span of the f
28. serted well Is the power supply 220V Insert the plug well If it is 110V connect raising power transformer The cooling is not enough Did you put hot food into the fridge Is there too much stored food in the fridge Is the distance between the fridge and other entity too near Is the ambient temperature below 5 or above 43 Hot food has to be cooled before it is put into the Leave proper clearance between foods Leave space between the fridge and its nearby entities Refer to installation method put the fridge in place where ambient temperature is 5 43 Large Noise or Abnormal noise Is the floor under the fridge firm and flat Noise is relatively large on stone or wood floor are there any entity at the back of the fridge Put the fridge on firm and flat floor Take away entity at the back of the fridge Bad smell in the fridge Is strong smell food sealed well Are containers close well Store the strong smell food in sealed container or bag Close the containers well Dew inside the fridge did you put hot food in the fridge Is the door open for a long time Did you open doors too often Is the container that stores high water content food close well Cool the hot food first before store in the fridge Wipe with dry cloth Reduce open door times Put food in container with cover or sealed well There is frost Is the door close well Did you put h
29. sides 4 places refer to Figure B on Page 19 Fix 5 upper gasket sheet with 14 wood screw and insert 12 bolt cover EEE a put 2 4 side gaskets into the left and right clearance between the refrigerator and the cabinet and stick them well Refer to Figure D on Page 19 Stick the magnetic part of gasket to the side panel of refrigerator When change the hinge position remember to insert 8 hinge hole sheet 6 places refer to Figure E on Page 20 Insert 7 hinge cover 4 places refer to Figure F on Page 20 install ventilation grill at the mop plate section of the refrigerator cabinet It is provided separately Refer to Figure G on Page 20 Fix the ventilation grill on the plug in in the mop plate Draw back the cover and fix the unfixed right side section of the refrigerator foot Refer to Figure H on Page 20 Use 15 hinge fixing screw to fix the hinge fixing hole refer to Figure on Page 20 Connect the power cord and confirm that it can function well Figure C Figure D Figure A Figure F Figure B l Figure I Figure E Figure G Figure H 40 Installation Sequences Figure A Assembly Method door Upper door door Lower door Figure C Assembly Method Figure D Assembly Method Refrigerator Cabinet 41 Installation Sequences Figure E Assembly Method When it is left open door take off
30. t is on press fresh food compartment temperature button A 3s the fresh food compartment is off the fresh food compartment indicator al is off When the fresh food compartment is off other set status as quick freezing intelligence timer ambient tem perature etc will continue to display When the fresh food compartment is off press the fresh food compartment temperature button A 3s the fresh food compartment is on again so is the fresh food compartment temperature indicator 8 Refrigerating Function Display When the refrigerating function is on the refrigerating function indicator a2 flashes When the refrigerating function is sleep status the refrigerating function indicator a2 is off 12 Functions and Temp Setting Method 9 Ambient Temperature Display and Setting of Present Time The ambient temperature and present time can be set and shown in display G Press fresh food compartment temperature button A and cooling speed button B at the same time ambient temperature display H and time display I will continuously show one after another Press ambient temperature H _Press time 1 _Press ambient temperature H _O Setting of present time press freezer temperature button C and intelligence button D at the same time to set time The default is 00 00 press fresh food compartment temperature button A to adjust hour it will change 1 hour every time you press once pr
31. t temperature display a1 when the sensor in the When power is off press power button F 3s all display will show and power is on fresh food compartment is faulty Then intelligence quick freezing quick refrigerating low temperature antibiosis cannot be used at that time F3 will show in freezer temperature display when the sensor in freezer is in fault Then the intelligence low temperature antibiosis cannot be used and related freezer alarms are also out of function F4 will show in ambient temperature and time display when the ambient temperature sensor is faulty the ambient temperature indicator H start to flash 13 Then the intelligence quick freezing quick refrigerating ambient temperature cannot be used Power failure memory function The fridge will keep its original set status when the fridge resumes work after power failure It can not only remember the set status before power failure but also the process of quick refrig 14 erating and quick freezing and re set automatically Precautions of moving the fridge Note When you move the fridge first press the power button to shut the fridge Draw the power plug when the power button is still on may damage the fridge Compressor Auto Safe Operation Frequent power on off and resuming work after power failure may cause damage and break down of the fridge The compressor auto safe operation function can make sure the compres sor is not overloaded Even ot

Haier HRF-305 User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents