Haier HK1270TVEME User's Manual
Contents
1. Possible cause The washing machine fails to operate Poor connection to power supply Power failure Door is not properly closed It will show E1 Machine has not been switched on Washing machine cannot be filled with water Water tap is not turned on It will show E5 Water pressure is less than 0 03Mpa The inlet hose is kinked Water supply failure The program dial is not properly set The door is not properly closed The inlet hose filter is blocked The machine is draining while is being filled The height of the drainage hose is below 80cm it should be within 80 100cm The drainage hose end is in water Drainage failure Drainage hose is blocked It will show E2 Drainage hose end is exceed 100cm above the floor level The filter is blocked Strong vibration during spin drying Not all packing bolts have been removed Washing machine is located on an uneven surface Machine load is over 7kg Not all foam packing has been removed from the motor Operation stops before completion of a wash cycle Water or electricity failure Washing machine is in soak cycle Operation stops for a period of time Washing machine is in soak cycle Washing machine gives an error message Excessive foam in the drum which is spilled to the distribution drawer The detergent is not a low foaming type or for manual wash Excessive use of detergent Installation Remove all2. be added This washing mashine is for househould use and designed for mechanically washable clothes When washing separate unwashable clothes with reference to clothes labels
3. programs do not add detergent to compartment 1 2 Do not overuse softener otherwise it will damage the artificial fibers Refer to the instructions during use 3 Selecting washing program To get the best washing effect an appropriate washing program should be selected according to the laundry type Note The above operations refer to conditions without power off memory Or the washing machine will continue operation from where the program was broken To clear memory press the Start Pause button Turn off the power for a few seconds and turn on again all the settings will be renewed Functions H Wash programming knob and start button By turning the knob clockwise or counterclockwise the required program can be selected press the start button to start a program press it again to pause l Speed button Press this button to set a required spinning speed which covers 0 rpm to 1200 rpm J Temperature button Press this button to set a required temperature The selectable temperature range is 0 90 Some programs have temperature limits Refer to the programming guide K Display Remaining time set temperature spinning speed other function information and error messages are displayed Refer to the Display Description L Detergent distribution drawer There are instructions on the handle of the distribution drawer Swing out the drawer three compartments can be seen Compartment 1 Pre washing detergent If pre wash is
4. the packing materials including the foam base to prevent vibration during use as shown in Fig 1 Upon opening of the package water drops may be seen on the plastic bag and the porthole This is normal phenomenon resulting from water test in the factory Operation manual Drainage holder Quality certificate HK1270TVEME Dismantle the packing bolts as shown in Fig 2 The packing bolts are designed for clamping anti vibration components inside of the washing machine during the transportation process Before use 1 Remove the back plate 2 Remove the three packing bolts on the back plate and take out the rubber hose 3 Replace the back plate 4 Fill the holes left by the packing bolts with plastic plugs Attention The packing bolts and rubber hose should be kept ina safe place for later use Adjusting the washing machine There are adjustable feet under the bottom of the washing machine Before use the washing machine should be adjusted as shown in Fig 3 so that it is level Maintenance 1 Turn of the water and electricity sup ply after every wash Open the door to prevent the formation of moisture and odors If the washing machine is left idle for a long period drain any remaining water in the machine and replace the drainage hose 2 Unplug the machine during cleaning and maintenance Use a soft cloth dampened with soapy Liquid to clean the machine case and rubber components Do not use cor
5. 0 90 C thick fabrics Cottam a White fabrics 0 90 C Coloured Fast color and medium soil 0 60 C fabrics Fast color Synthetic i and heavy oog soil fabrics faucet to ensure the water faucet and the water inlet hose are connected correctly and do not leak 4 Detergent selection 3 Laundry treatment Only special low foam detergent should Sort out clothes according to type and extent of dirt There are be used in automatic drum washing three types of clothes cotton synthetical and woolen silk fabrics mashine form blended or wool fabrics Separate white clothes from colored If whites and coloreds special deter gent should ne used dry are combimed for one load make sure the coloreds are colorfast clearning solvent should not be used such as trichhloroethy lene or alike caution load the required amount of detergent only fm a Clothing with frayed edges or yams should be put in a wash bag or special bag before washing repair damged clothing lose buttons or damaged zips and hooks before washing Bed sheets and table ware should be loosely loaded and not folded Medium soil Quick 29min cotton amp 0 40 C synthetics ne E 5 Wash Load Note 0 indicates that softener or bleacher can be added if needed Delicate fabrics Woolen fabrics indicates that detergent must be added paves X indicates that detergent must not be added eno 2kg indicates that if pre wash is selected detergent must
6. T 14 am Q _ iq _ ab Q Haier Automatic Drum Washing Machine HK1270TVEME Table of Contents Before using the appliance Name of parts inside front cover Matters needing attention 1 3 Installation Function Program description table Preparation Washing Procedure Maintenance Troubleshooting Guide Technical Specifications Wiring Circuit Name of Parts nN Detergent ma n zN Top Program selector E ON OFF button Handle Function selector Door Porthole Bottom plaque Power supply cable Earth terminal Drain hose clip Back plate screw 3 Packing bolt 3 Drain hose Back plate Caution and Warning symbols For you safely any instructions in this manual with this Warning sign must be followed strictly For your safety and to prevent damage to the washing machine any instructions in this manual with this Stop sign must be followed strictly This diagram may be slightly different from the layout of the washing machine you have just purchased due to techincal improvements Matters Needing Attention Safety 1 A separate earthed socket is required for the 2 Hold the plug and not the electric cable when power supply The washing machine must be unplugging the washing machine positioned so that the plug is accessible If the supply cord is damaged it must be replaced by the manufacturer its service agent or similarly qualified pers
7. not selected do not add detergent Compartment 2 Detergent for all washing programs Detergent must be added whether pre wash is selected or not Compartment 3 Softening agent conditioning agent perfume etc B C combination for keyboard lock After a program is started press the delay tbutton and the Prewash button at the same time for 3 seconds the keyboard will be locked and SAFE ON will appear on the screen Press the two buttons again for 3 seconds the keyboard will be unlocked and SAFE OFF will be displayed This function is used to protect the washing machine from being disturbed during operation such as accidental press of buttons or turning of knobs by children as this may affect or suspend the operation of a program Note If this function is activated during a washing cycle be sure to inactivate it at the end of the cycle when the End sign is displayed Caution If the keyboard lock is not activated press the Start Pause button and then cut off the power the suspended program will be canceled after power is resumed Now turn the program knob to reselect Program Description Table Preparation Mode Selection Recommended Selectable Program Time Detergent 1 Power supply 2 Water supply Temperature At Max Plug in the power supply 230V 50HZ Turn on the tap ensure that the water in clear Button Position Program Temperature Caution Before staring the washing machine turn on the water Intense Heavy and
8. ons in order to avoid a hazard Z to ing agent do not use flammable spray in close during the heating process Avoid contact with the vicinity to the washing machine do not remove door during the heating process For safety keep or insert the plug in the presence of flammable children away from the washing machine Wiring Circuit HK1270TVEME N L Pee Power Switch H ST 7 i gt s15 Display PCB toi e T3 i J12 3 gt ST 0246 312 4 ey Dig J12 11 do le ST7 Door Lock gt metre PD Ge J12 12 jaa epN Mace E ANT i 53 J12 EE m Thermostat r deM1B1 Power Drive PCB Hie 112 10 Pressure Switch Heating Element 15 Matters Needing Attention 8 The washing machine should not be installed 9 The carpet must not obstruct the ventilation openings in the base of the washing machine outdoors or in a damp place In the event of water leakage or splashes allow the machine to dry naturally During Use Before use check the joints of the filling hose the tap and the drainage hose for possible problems from water pressure fluctuations If joints are loose or there is leakage turn off the tap and repair Do not use the washing machine until the hoses are properly fixed A cS 2 cable is not trapped by the washing machine and avoid damage to the electric cable 2 Keep the door slightly open when the washing machine is not in use to prevent formation of odors do n
9. ot compatible Refer to a washing machine technician or a Haier designated service point for power cable replacement The washing machine should be connected to the earth before use Supplementary earth cable should not be necessary if the socket is connected to the earth Supplementary earth cable should be installed on the upper back of the washing machine and connected to an earth if the power supply socket has no earth connection Caution the supplementary earth cable should not be connected to water or heating pipes Operational Functions Te Spoed Haier morowwe oyr EGG 4 Oo s Super Wash Load Select ON OFF OO O A DIGITAL 7KG peel ee me n OQ D A lroning free button Press this button the laundry will be fluffed up at the end of the spinning cycle to reduce wrinkles B Delay button Press the Delay button before the program is started if necessary Press of the Delay button one time the delay time will increase one hour the regulating range is from the current setting to 24 hours After the delay time is changed press the Start button to activate the delay function Note The delay time must be longer than the program time otherwise the washing machine will start the wash program directly C Pre wash button Press this button the washing machine will automatically start a prewash cycle during execution of a washing program D E
10. ot cover the washing machine with plastic cover so that inside dampness cannot be kept in Matters Needing Attention Technical Specifications 3 Do not place heavy heating source or wet articles 4 Do not hot wash foam rubber or sponge like on the top of the washing machine materials Power supply Power Max Water pressure MPa Washing power W Spinning power W 5 Before washing do up zippers buttons and clothes 6 Do not open the detergent distribution drawer Max wash load kg straps and put small articles such as socks laces during the wash cycle HK1270TVEME 230V 50Hz 0 03 lt P lt 1 7 or bras into a washing bag or a pillow Spinning speed MAX rimin 4200 Wash program Heating power W Steel wires in bras will pop p out during washing never 7 Weight kg wash bras containing steel 3 wires ce Anti Electric Shock l i f Anti Water Class 7 The door is fitted with a self lock device and will not 8 After each wash program turn off the tap to prevent open until 2 3 minutes after the washing machine leakage and unplug the washing machine and stops Do not force the door open Do not open the wipe clean the lower part of the porthole door if water level can reach the porthole 9 1800 14 13 Troubleshooting The following circumstances do not constitute problems Do not contact the maintenance service until the problem has been confirmed Problem
11. r inlet valve Water drainage hose The height of the terminal of the water drainage hose should be between 80cm 100cm the water drainage hose must be securely placed on the clip on the back of the washing machine Use the water drainage support supplied as an accessory for proper installation of the water drainage hose Fix the water drainage hose support with waterproof string Do not use an excessively long water drainage hose and contract the authorized technician if the water drain age hose needs to be extended The water drainage hose should not be extended more than250cm longer extension will result in concur 100cm 80cm rent water inflow and outflow The diameter of the extension hose should be the same as the original hose caution water drainage hose must not be immersed in water the origi nal and extension hoses should be tightly connected The appliance is to be connected to the water mains using new hose sets and that old hose sets should not be reused Connection of power supply 7 Check the following items before connection to the power supply The socket conforms to the maximum power load The maximum current load of the socket and power supply cable should not be less than 15A power supply voltage conforms to the required value The power supply socket and the plug of the washing machine should be compatible if they are n
12. rosive or abrasive chemicals or solvents 3 Clean the detergent compartment regularly For the detergent compartment similar to figure a raise the compartment slightly to remove and replace after cleaning Fig a 4 Clean the filter Cleaning methods once a month 1 Push out the outer cover Fig 1 2 Screw out filter by turning counterclockwise Fig 2 3 Flash clean with running water 4 Replace the filter by turning clockwise and remount the cover Caution The filter must be in place or it may lead to leakage 6 If the machine is to be moved a distance location replace the vibration mounting locks wien were removed during installation as snown elow 5 To prevent block ages to the water supply or the ingress of contaminants clean the water inlet and inlet water filter regularly 7 If the washing machine is left idle for a long period turn off the water and electricity supply and open the door slightly to prevent the forma tion of moisture and odors Remove the back cover plugs Remove the rubber Insert the bolts Tighten the bolts with the Replace the rear spanner provided panel Installation Connection of water inlet hose and washing machine 7 water inlet hose nut Me 2 slightly shake the water inlet hose nut to see if Z it is tightly and properly fixed connector of water inlet valve 1 Place the water inlet hose nut on the connector of the wate
13. ving energy During operation 1 Collect clothes for one full wash load 2 Do not overload the washing machine 3 Pre wash heavily soiled clothes 4 Reduce the amount of detergent or choose standard or delicate wash programs for slightly soiled clothes 5 Choose a proper washing temperature Only exceed 60 C for heavily soiled clothes 6 Do not use more detergent than required 7 Softening agent makes clothes feel softer and easier to iron 1 10 Washing Procedure 1 Loading Open the door put in the laundry piece by piece Close the door tightly Notes 1 When first using the washing machine let it run unloaded for one program Load Reference Jeans Overalls pie cotton appr pall e pajamas appr e Blended D ii i z to prevent the laundry from being tainted by clot oil or dirty water from the washing machine 2 Do not overload the washing machine O SD appr 8009 f Shirts appr 300g ERN ar ats Dy eis appr my blended fabrics appr 70g Socks blended amp fabrics appr 50g Single bed sheets cotton appr 800g appr 3600 Jackets feotton appr 800g 2 Adding detergent Slide out the detergent drawer and put the required detergent and softening agent into the corresponding boxes Push back the drawer gently Caution 1 For pre washing program detergent should be added to both compartments 1 and 2 Compartment 2 allows only solid detergents For other
14. xtra rinsing button Press this button the washing machine will run an additional rinsing cycle to further clean your clothes E Super wash button Press this button the display will be on when choosing super wash button The S JPEA and NO SPEA will display circularly The sign of super wash will be off when the super wash system finished F Washing load button SSS 0 4 6kg will appear on the screen for manual selection before water is filled After the load is set the water content will be automatically adjusted G Power button Press this button to switch on the washing machine press it again to switch the machine off To cancle a wash program during a wash cycle please switch the machine off Hints for Saving Energy 4 Setting washing temperature Press the temperature button until _ _ C is displayed if heating is not needed otherwise select an appropriate temperature as required refer to the Guide to Operational Program Selection 5 Function selecting button Select functions as required refer to the Operational Functions section 6 Washing Press the Start Pause button the indicator at the upper left corner of the button will blink and the washing machine starts operation 7 Finish The washing machine will stop operation automatically when a wash cycle ends The End sign will appear Open the door and take out the laundry Then turn off the tap and unplug the power cable Hints for sa
Download Pdf Manuals
Related Search